DORMAN 740-724 Front Passenger Side Power Window Regulator Instruction Manual

DORMAN 740-724 Front Passenger Side Power Window Regulator

Product Information

Specifications

• Product Name: Window Regulator
• Part Number: 740-724
• Tools Required: Trim panel removal tool, screwdriver, safety glasses

Product Usage Instructions

Removal Instructions

1. Using a trim panel removal tool, remove the screw covers that retain the interior door trim panel.
2. Using a trim panel removal tool, remove the screw cover for the door handle pull assembly and remove the door handle pull assembly retaining screw.
3. Disconnect the window switch assembly.
   • NOTE: Switch may vary in appearance depending upon your vehicle’s options.
4. Using either a pick or a small flat-blade screwdriver, remove the screw cover. Remove the interior door trim panel retaining screw using a Phillips head screwdriver.
5. Using a trim panel removal tool, place it between the door and the interior door trim panel. Using firm, even pressure, release the interior door trim panel from the door.
6. To remove the interior door trim panel, pull the interior door trim panel toward you and lift it in an upward motion.
7. Using a Phillips head screwdriver, remove the interior door trim panel support bracket.
8. Remove the water vapor barrier.

Frequently Asked Questions (FAQ)

Q: Do I need to wear safety glasses during the installation/removal process?

A: Yes, it is highly recommended to wear safety glasses to protect your eyes during the process.

Q: Can I install the window regulator without a service manual?

A: It is recommended to refer to the appropriate shop manual for your vehicle for specific service procedures. If you lack the skill or manual, seek help from a qualified technician.

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

REMOVAL/INSTALL OF WINDOW REGULATOR (740-724) Nissan Altima 1993–97

General Tech Tips:

• Use painter’s tape rather than duct tape to secure the window. It will not damage paint or leave a sticky residue.
• A plastic pry tool is useful. It will not easily damage delicate trim like a screwdriver or metal pry bar.
• The replacement regulator should have a liberal amount of grease on the slide area. If there is not much grease present, white lithium grease works well to lubricate the slide area.
• Aftermarket window tinting can cause the window to travel slower and put additional strain on the window regulator assembly.
• Window run channels should be cleaned and lubricated before the installation of a new window regulator assembly. Silicone spray works well.

Tools required

• Tools required for removal and installation of a window regulator and motor assembly:
• Silicone spray lubricant
• Trim panel removal tool
• Pick
• Saddle cup assembly, tape, or wedge to hold a window in place
• Flat-blade screwdriver or plastic pry tool
• 10mm socket or driver
• Phillips screwdriver
• Grease pencil or marker

PLEASE WEAR SAFETY GLASSES!

• ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part.
• If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician.
• Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

Removal Instructions

1. STEP 1: Using a trim panel removal tool, remove the screw covers that retain the interior door trim panel.
2. STEP 2: Using a trim panel removal tool, remove the screw cover for the door handle pull assembly and remove the door handle pull assembly retaining screw.
3. STEP 3: Disconnect the window switch assembly. NOTE: Switch may vary in appearance depending upon your vehicle’s options.
4. STEP 4: Using either a pick or a small flat-blade screwdriver, remove the screw cover. Remove the interior door trim panel retaining screw using a Phillips head screwdriver.
5. STEP 5: Using a trim panel removal tool, place between the door and the interior door trim panel. Using fi rm, even pressure, release the interior door trim panel from the door.
6. STEP 6 : To remove the interior door trim panel, pull the interior door trim panel toward you and lift it in an upward motion.
7. STEP 7: Using a Phillips head screwdriver, remove the interior door trim panel support bracket.
8. STEP 8: Remove the water vapor barrier.
9. STEP 9: Temporarily install the window switch to lower the window glass, exposing the window glass to the window regulator and attaching screws.
10. STEP 10: Once the window glass has been disconnected from the window regulator, manually slide the window glass into the closed position and hold it in place with either a saddle cup assembly, painter’s tape, or a wedge.
11. STEP 11: Disconnect the window lift motor connector.
12. STEP 12: Push the window lift motor connector through the access hole in the door.
13. STEP 13: Using your ratchet with a 10 mm socket, remove the three screws that attach to the window regulator assembly.
14. STEP 14: Using your ratchet with a 10 mm socket, remove the remaining window regulator attaching hardware.
15. STEP 15: Remove the window regulator assembly through the main access hole.
16. STEP 16: Remove the three window lift motor attaching screws.

Installation Instructions

1. STEP 1: Attach the three window lift motor attaching screws.
   • STEP 1a: Place the window regulator through the main access hole. Once the window regulator assembly is placed into position, loosely mount the window regulator assembly with its attaching hardware.
2. STEP 2: Slide the window lift motor connector through the access hole.
3. STEP 3: Connect the window lift motor connector.
4. STEP 4: Using your ratchet with a 10 mm socket, tighten down the window regulator attaching hardware.
5. STEP 5: Manually slide the window glass onto the window regulator.
   • NOTE: It may be necessary to temporarily connect the power master switch assembly to align the window glass to the window regulator.
6. STEP 6: At this point, verify that the window regulator is operating properly. Once this has been verified, disconnect the power master switch assembly.
7. STEP 7: Install the water vapor barrier.
8. STEP 8: Attach the interior door trim panel reinforcement bar.
9. STEP 9: Install the interior door trim panel.
   • NOTE: When installing the interior door trim panel, pull the door trim panel in a downward motion.
   • Be sure to align the door trim panel on the lip of the door and align the interior door trim panel retaining hardware with its corresponding holes.
   • Once everything is aligned, press the interior door trim panel into position.
10. STEP 10: Connect the power window switch connector.
11. STEP 11: Attach the power window switch assembly onto the interior door trim panel.
    • NOTE: Your vehicle switch may vary in appearance depending upon which options you vehicle came with.
12. STEP 12: Attach the interior door trim panel attaching screws.
13. STEP 13: Attach the door handle pull attaching screw. Install the screw cover assembly.
14. STEP 14: Verify that all of the interior door trim panel attaching hardware is secure and that the window regulator is operating properly.

• We appreciate your opinions regarding this product!
• Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product.
• 1-800-523-2492

Disclaimer:

• Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations.
• Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions.
• Failure to do so may result in property damage or personal injury.
• Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration).
• Be sure that your work is performed under such standards and that you do not disable any motor vehicle safety features.
• ©2012 Dorman Products, Inc.
• No reproductions in whole or in part without prior written approval.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>