Dorman 740-822 Front Passenger Side Power Window Regulator Instructions
- June 1, 2024
- DORMAN
Table of Contents
Dorman 740-822 Front Passenger Side Power Window Regulator
Product Information
Specifications
- Product Code: 740-822
- Product Type: Window Regulator
- Tools Required: Trim panel removal tool, Phillips head screwdriver, small flat-blade screwdriver, 8 mm socket
- Additional Requirement: Silicone spray for assembly
Product Usage Instructions
Removal Instructions
- STEP 1: Using a trim panel removal tool, remove the rear view mirror bezel.
- STEP 2: Remove the Phillips head screw attaching the interior door handle bezel assembly to the door.
- STEP 3: Disconnect the power door lock switch.
- STEP 4: Using a pic or small flat-blade screwdriver remove the interior door trim panel attaching screw cover.
- STEP 5: Using an 8 mm socket remove the door trim panel attaching screws.
- STEP 6: Using a trim panel removal tool, remove the interior door trim panel. NOTE: You may want to use a plastic trim panel tool to prevent scratching the painted surface.
- STEP 7: With the interior door trim panel removed from the door, disconnect the master power switch assembly. NOTE: The switch connectors may vary.
Frequently Asked Questions (FAQ)
-
Q: What tools are required for the installation of the window regulator?
A: The tools required for installation include a trim panel removal tool, Phillips head screwdriver, small flat-blade screwdriver, and an 8 mm socket. -
Q: Can I install the window regulator without a service manual?
A: It is recommended to refer to the appropriate shop manual for your vehicle to obtain specific service procedures for installing the window regulator. If you lack the skill or experience, it is advised to seek the services of a qualified technician.
INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualifi ed technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.
REMOVAL/INSTALL OF WINDOW REGULATOR (740-822) Chevrolet Malibu 1997–2003, Chevrolet Malibu Classic 2004–05, Oldsmobile Cutlass 1997–99
General Tech Tips
- Use painter’s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue.
- A plastic pry tool is useful. It will not easily damage delicate trim like a screwdriver or metal pry bar.
- The replacement regulator should have a liberal amount of grease on slide area. If there is not much grease present, white lithium grease works well to lubricate the slide area.
- Aftermarket window tinting can cause the window to travel slower and put additional strain on the window regulator assembly.
- Window run channels should be cleaned and lubricated before installation of a new window regulator assembly. Silicone spray works well.
Tools required for removal and installation of window regulator and motor assembly:
- Silicone spray lubricant
- Trim panel removal tool
- Pick
- Saddle cup assembly, tape or wedge to hold window in place
- Flat-blade screwdriver or plastic pry tool
- 10 mm socket or driver
- Phillips screwdriver
- Grease pencil or marker
- 8 mm socket
PLEASE WEAR SAFETY GLASSES!
ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualifi ed technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.
Removal Instructions
- STEP 1 : Using a trim panel removal tool, remove the rear view mirror bezel.
- STEP 2 : Remove the Phillips head screw attaching the interior door handle bezel assembly to the door.
- STEP 3 : Disconnect the power door lock switch.
- STEP 4 : Using a pic or small fl at-blade screwdriver remove the interior door trim panel attaching screw cover.
- STEP 5 : Using an 8 mm socket remove the door trim panel attaching screws.
- STEP 6 : Using a trim panel removal tool, remove the interior door trim panel. NOTE: You may want to use a plastic trim panel tool to prevent scratching the painted surface.
- STEP 7 : With the interior door trim panel removed from the door, disconnect the master power switch assembly. NOTE: The switch connectors may vary.
- STEP 8 : Remove the interior door trim panel.
- STEP 9 : Remove the four (4) door speaker attaching screws.
- STEP 9 : Remove the four (4) door speaker attaching screws.
- STEP 11 : Once the door speaker has been removed, remove the water vapor barrier.
- STEP 12 : Disconnect the interior door handle latch rods from the interior door handle.
- STEP 13 : Remove the Phillips head screw that holds the interior door handle assembly onto the door.
- STEP 14: Temporarily connect the power window switch to lower the door glass to expose the two (2) door glass attaching bolts.
- STEP 14a : Once the door glass is disconnected from the window regulator, slide the door glass into the up position and hold in place with either a saddle cup assembly, tape, or wedge.
- STEP 14b : Disconnect the window lift motor.
- STEP 15 : Remove the window regulator assembly attaching screws.
- STEP 16 : With the window regulator assembly removed, remove the three (3) window lift motor attaching screws. NOTE: BE VERY CAREFUL WHEN REMOVING THE WINDOW LIFT MOTOR. THE PRE TENSIONER SPRING IS UNDER PRESSURE AND CAN INFLICT BODILY INJURY IF EXTREME CAUTION IS NOT USED.
Installation Instructions
- STEP 1 : Install the window regulator onto the plastic panel assembly.
- STEP 2 : Attach the three (3) window lift motor attaching screws to the window lift motor.
- STEP 3 : Install the window regulator assembly onto the door.
- STEP 3a : Connect the window lift motor.
- STEP 3b : Attach the window regulator assembly attaching screws.
- STEP 4 : Temporarily install the master power switch assembly to raise or lower the window regulator for the door glass attaching points.
- STEP 4a : Lower the door glass into position and attach to the window regulator.
- STEP 5 : Install the interior door handle.
- STEP 5a : Connect the interior door handle latch rods.
- STEP 6 : Attach the water vapor barrier.
- STEP 7 : Install the door speaker
- STEP 7a : Connect the door speaker.
- STEP 8 : Connect the master power switch assembly.
- STEP 9: Align the interior door trim panel retainers with their corresponding holes and push the interior door trim panel into place.
- STEP 10: Attach the interior door trim panel retaining screws.
- STEP 11 : Install the interior door trim panel attaching screw cover.
- STEP 12 : Connect the power door lock switch.
- STEP 12a : Install the interior door handle bezel assembly.
- STEP 13 : Install the rear view mirror bezel assembly.
- STEP 14 : Verify that the window regulator is operating properly and that all of the interior door trim panels retainers are installed.
We appreciate your opinions regarding this product!
Please call our Technical Assistant with any challenges or suggestions
regarding the installation or operation of this product.
1-800-523-2492
Disclaimer
Even though every attempt is made to ensure this information is complete and
accurate, it is impossible to account for all possible circumstances or
situations. Please consult with a qualified auto technician before attempting
to perform any work you are not qualified to do. Automobiles can be hazardous
to work on; be sure to take all necessary safety precautions. Failure to do so
may result in property damage or personal injury. Certain motor vehicle
standards and performance requirements may apply to your motor vehicle (such
as Federal Motor Vehicle Safety Standards by the National Highway Traffic
Safety Administration). Be sure that your work is performed in accordance with
such standards and that you do not disable any motor vehicle safety feature.
©2011 Dorman Products, Inc.
No reproductions in whole or in part without prior written approval.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>