Zowill DK07 6 In 1 Smart Door Lock for Front Door Fingerprint Door Lock Installation Guide

Zowill DK07 6 In 1 Smart Door Lock for Front Door Fingerprint Door Lock

Product Information

The device is compliant with part 15 of the FCC Rules and contains licence- exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). The device should be installed and operated with a minimum distance of 20cm between the radiator and the user’s body. The device should not cause harmful interference or operate undesirably even if it receives interference.

Product Usage Instructions

1. Do not make any changes or modifications to the device that are not explicitly approved by the manufacturer, as this may void your authority to operate the equipment.
2. Install and operate the device with a minimum distance of 20cm between the radiator and your body to comply with FCC and Canada radiation exposure limits for an uncontrolled environment.
3. Ensure that the device does not cause any harmful interference or operate undesirably even if it receives interference.

Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures In this manual are for illustration purpose only. Actual products may vary due to product upgrades.

TOOL REQUIRED
Do not use an electric screwdriver during installation.

INSTALLATION OVERVIEW

Parts List

If any parts are lost or damaged, please contact Customer Support.

ASSEMBLY

STEP 1
Prepare the door and check dimensions

• A. Measure to confirm that the hole in the door is 1-1/2″ or 2-1/8″ (38mm or 54mm)
  Measure to confirm that the hole in the door edge is 1″ (25mm).

• B. Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)

• C. Measure to confirm that the door is 1-3/8″ to 2″ (35 mm or 50mm) thick.

• D. Make sure the hole in the door frame is drilled a minimum of 1″ (25mm) deep, to leave enough space for the deadbolt to extend into the door frame when the door is locked.

Notes: Make sure the door frame is aligned with the door.
There are no obstructions stuck in the door frame.

STEP 2
Install the latch and strike

• A. Determine backset and adjust the latch
  Hold the latch in front of the door hole,with the latch face flush against the door edge. Is the slotted hole centered in the door hole?
  YES
  No adjustment is required.
  Proceed to next step. NO
  Slotted hole is NOT centered.
  Rotate and pull the latch as shown to extend latch.

• B. Install the latch
  

• C. Use a screwdriver to test if deadbolt works smoothly.

• D. Install strike on the door frame.
  IMPORTANT:
  Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.

STEP 3
install exterior assembly

IMPORTANT:
Before installation, make sure the latch is fully retracted (in the unlocked position)

• A. Measure the diameter of the hole in the door.
• B. With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the tailpiece through the slot in the latch.
• C. Secure the mounting plate with the supplied screws. Do not overtighten screws.

STEP 4
Install interior assembly

• A. Push the battery cover out in the direction as illustrated.
  IMPORTANT:
  Do not load batteries until lock is completely installed.

• B. Determine the door is right-handed or left-handed.
  Notes: If the direction of the slide switch is set incorrectly, it can be reset in DDLock App.

• C. Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.

• D. Attach Interior Assembly to Mounting Plate and tighten 3 Screws.

• E. Insert 4 AA Alkaline batteries and put on the battery cover.

PROGRAMMING INSTRUCTIONS

At a Glance

How to Use

UNLOCK the door from outside

LOCK the door from outside

1. Auto Lock Mode
   In Auto Lock mode,the bolt will extend out automatically in 5 seconds after unlocking.

2. Manual Mode
   Press # on keypad for 2 seconds.

UNLOCK the door from inside

Rotate the thumb turn to Unlock position.

LOCK the door from inside

• Auto Lock Mode
  In Auto Lock mode,the device will be locked automatically.

• Manual Mode
  Rotate the thumb turn to Lock Position.

Definitions

• Master Code
  Required for programming and feature settings. The default master code needs to be changed before programming.
  Property owner & manager should keep this information confidential.

• Auto Lock
  Automatically locks the deadbolt 5 seconds after unlocking. This feature is off by default. You can customize the Auto Lock time delay between 1 and 900 seconds.

• Key Unlock
  Key Unlock is always available when the batteries are completely dead or valid User Codes are forgotten.

• Low Battery Indicator
  If you hear 3 beeps along with 3 red light flashing after pressing any key to lock or unlock the door, that’s an alert for replacing batteries. Please replace with 4 brand new AA alkaline batteries and do not mix used and new batteries. All settings are stored in the lock while the batteries are removed and replaced.

• Wrong Entry Limit
  After 5 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 2 minutes.

Programming Basic

• Silent Mode
  The beep sounds when pressing keypad can be muted. But you will still hear low battery and system alerts.

• Unlock with Fake code
  User can prevent pin code exposure from strangers by entering random digits before or after pin code. The total password length is within 16 digits.

Quick Set Up

IMPORTANT:
The default Master Code is 1 2 3 4 5 6.
It is required that you change it to a code of your own before programming.

Notes:

1. Beeps only sound when the Silent Mode is disabled.
2. If the indicators flash red light, it means your setting failed.
3. After adding code/fingerprint/card successfully, you can choose to continue adding or automatically exit the adding program after the screen fades out.

Factory Default Settings

How to Reset?
Press and hold the Reset button on the interior assembly by using the reset tool, stop holding until you hear a short beep and see 1 green light flash.

IMPORTANT
The reset button function must be turned on in the DDLock App before reseting.

DDLOCK USE GUIDE

HOW TO REGISTER

STEP 1
Download “DDLock” App in Google Play or App Store.

STEP 1
Tap on register to get started !

STEP 2
Fill out this and then tap “Get Code”
You will be sent a verification code to verify your account!
Once you receive it,tap on “Register”

Notes:
The DDLock app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeowner), make sure this step is performed by the homeowner.

Pairing Your Lock

Admin Passcode Management

After pairing the lock with DDLock, the admin passcode will be changed to a random 7 digit number, you can check the new admin passcode by following the picture guide below. And you can change it to your own administrator password.

Lock Page Overview

Unlock/Lock
Unlock/Lock using phone’s bluetooth
Passcode
Generate 6 different types of passcodes
eKey Page
View and modify current eKeys
Records Page
View entry times, attempts and methods

Settings Page
View and modify settings
Authorized Admin Page
Create and edit admins
Cards
Set up your cards here
Fingerprints Page
Set up fingerprints

Notes: Some of these icons may not appear if the Gateway is not connected to the lock.

APP Unlock/ Lock

To unlock the lock, tap this icon once.
To lock the lock, press and hold on this icon.

Passcode

STEP 1
To access the passcode menu, tap on ” Passcode” icon.
This will take you to the passcode page.

STEP 2
Tap on “Generate Passcode”.

STEP 3
Enter a name for this Passcode.

IC Card

STEP 1
Tap on “Cards”_

STEP 2
Tap on “Add card”.

STEP 3
Choose the validity period of the lock.
Once the lock says
“Please swipe your card”, place the card against 5 on the keypad.
If you hear a long beep, the card can be used to unlock your lock.

Fingerprints

To add a fingerprint follow these instructions:

STEP 1
Tap on Fingerprints.

STEP 2
Tap on “Add Fingerprints”.

STEP 3
Select Fingerprint type depending on when you would like it to be valid_ Follow instructions on app. You will be asked to place your finger on the sensor 4 times.

eKeys

STEP 1
eKeys work by sharing app access of your lock with another DDLock account. eKey recipients will be able to use their phone to unlock/lock the lock.

STEP 2
Tap on “Send eKey'”

STEP 3
Enter recipient’s username. It will be the phone number or email address during registration.
eKeys do not require wifi or bluetooth to be sent or revoked.

Authorized Admin

Authorized Admins are similar to eKeys; however, an authorized admin can do the following:

STEP 1

1. Unlock/lock via the app.
2. Generate, Edit, Delete passcodes, IC cards, & fingerprints.
3. Adjust settings like passage mode, auto-lock timer, & turn on/off the lock sound_

STEP 2
Tap on “Authorized Admin” Set Timed Admin or Permanent Admin.

Passage Mode & Auto-Lock

STEP 1
Auto-lock will automatically lock the lock when it has be opened after 5 seconds by default. This can be adjusted with Passage Mode and Auto-lock timer. Outlined below is how to adjust these settings related to auto-lock.

STEP 2
Select Passage Mode.

STEP 3
Passage Mode disables auto-lock during a set schedule.

Lock Settings

Here are some settings you should familiarize yourself with.

• Under Basic you can view and change information such as Lock Name.
• Gateway shows signal strength if Gateway is connected.
• With ‘Remote Unloc€on and a Gateway connected, you can remotely unlock/lock your lock.
• Lock Sound adjusts the locks sound level.
• Import from another IocKallows for the transfer of passcodes and cards from one lock to another.
• Delete will remove the lock from your account and clear any settings one the lock. You must be near the lock do this.

Troubleshooting

Q: Why the lock won’t accept any inputs after I entered a code or fingerprint incorrectly for so many times?
A: The lock will shut down for 2 minutes after 5 unsuccessful attempts at entering an invalid code or fingerprint.
You can unlock the lock once in the App or wait 2 minutes to continue.

Q: How do I lock manually from outside?
A: Press and hold # to lock the lock from outside.

Q: The batteries are completely dead before I replace new batteries.
A: When the batteries are completely dead, the physical keys are available to unlock.

Q: How do I share access of the lock to my family members?
A: Go to DDLock App, in eKeys or Authorized Admin, it can share access of the (ock to your family.

Q: Why the thumb turn won’t turn to lock/unlock?
A: The door direction might be set wrong during the installation, please follow the Installation guide or video to re-install the lock.

Q: When I tap on Lock in App, the deadbolt unlocked and retracted; When I tap on Unlock in App, the deadbolt locked and extended.
A: The door direction has been set wrong. It can be changed in Settin!)s Door opening direction in DDLock App.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES‐3
(B)/NMB‐3(B).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

Information & Safety Warnings 

• Protect your User Codes and Master Code.
• Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
• The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.

The Video of Installation and Programming Guide

Website: www.zowill.com
Service: support@zowill.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>