ZALMAN Z7 NEO ATX MID Tower User Manual
- June 4, 2024
- ZALMAN
Table of Contents
- Precautions
- Features
- I/O Ports
- | Part| #| Part| #| Part| #| Part
- Dismantling the side panels
- Dismantling the front panel
- Mounting the motherboard
- Mounting the power supply
- Mounting the PCI-E (VGA) Card
- Mounting 3.5” and 2.5” SSD / HDD
- Mounting 3.5” and 2.5” SSD / HDD
- Assembly of the upper fans
- Mounting the front radiator
- Fan Features
- I/O connectors
- RGB LED Controller
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZALMAN Z7 NEO ATX MID Tower User Manual
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Features
Model | Z7 NEO |
---|---|
Case Form Factor | ATX Mid-Tower |
Dimensions | 420 x 213 x 460(H)mm |
Weight | 7.2kg |
Case Materials | Plastic, Steel, Tempered Glass |
Motherboard Support | ATX / mATX / Mini-ITX |
Maximum VGA Length | 355mm |
Maximum CPU Cooler Height | 165mm |
Maximum PSU Length | 180mm |
PCI Expansion Slots | 7 |
Drive Bays | 2 x Combo (3.5” or 2.5″), 2 x 2.5” |
Fan Support | Top |
Front | 3 x 120mm |
Rear | 1 x 120mm |
Pre-Installed Fan(s) | Front |
Rear | 1 x 120mm (with RGB LED Effect) |
Radiator Support | Top |
Front | 120mm / 240mm / 360mm |
I/O Ports | 1 x USB 3.0, 2 x USB 2.0, 1 x Headphone Jack, 1 x Microphone Jack, |
LED Control Button, Reset Button, Power Button
Caution (Radiator Support)
※ Limited fitment to memory equipped with heatsinks.
※ Some motherboards with tall heat sink will cause interference on the
installation of the 280mm radiator.
I/O Ports
| Part| #| Part| #| Part| #| Part
---|---|---|---|---|---|---|---
a| USB 3.0 Port| b| USB 2.0 Ports| c| Headphone Jack|
d| Microphone Jack
e| HDD / Power LED| f| LED Control Button| g| Reset Button|
h| Power Button
Dismantling the side panels
-
Tempered Glass
-
Steel Panel
Dismantling the front panel
Mounting the motherboard
-
ATX
-
mATX
-
Mini-ITX
Mounting the power supply
Mounting the PCI-E (VGA) Card
Mounting 3.5” and 2.5” SSD / HDD
HDD
SSD
Mounting 3.5” and 2.5” SSD / HDD
Assembly of the upper fans
Mounting the front radiator
Caution
※ Limited fitment to memory equipped with heatsinks.
※ Some motherboards with tall heat sink will cause interference on the
installation of the 280mm radiator
Fan Features
RPM : 1200± 10%
Input : 12V 0.6A
I/O connectors
RGB LED Controller
RGB LED Controller Position SW IR LE01 LE02
-
A. Fan 1~8 / 6Pin
- Connector to RGB LED fans (Four pre-installed)
- RGB LED Fans I/O port 8ea
-
B. LED Control Button / 2Pin
- Connector to LED control button
- RGB LED Lighting effects & 7 Colors
-
C. DC Power / 4Pin
- Connector to PSU
- Input : 12V
-
D. Motherboard Sync / 4Pin
- Connector to motherboard
- Requires motherboard that supports RGB sync
※ Caution
Please be sure to check the arrow of the female cable, it indicates where 12V
needs to be connected when you are connecting it to motherboard.