BOMANN EBK 7940 Built In Hob Instruction Manual

BOMANN EBK 7940 Built In Hob

INSTRUCTION MANUAL

Introduction

Thank you for choosing our product. We hope you will enjoy using the appliance.

Symbols in these instructions for use

Important information for your safety is specially marked. It is essential to comply with these instruc-tions to avoid accidents and prevent damage:

WARNING:
This warns you of dangers to your health and indi-cates possible injury risks.

CAUTION:
This refers to possible hazards to the machine or other objects.

NOTE: This highlights tips and information.

General notes

Read the operating instructions very carefully before putting the appliance into operation and keep the instructions including the warranty and the receipt. If you give this appliance to other people, also pass on the operating instructions.

NOTE:

• Due to constant product modifications, your appli-ance may differ slightly from these operating in-structions; Functions and methods of use remain unchanged.
• The illustrations in these operating instructions are for illustrative purposes only and may differ from the original appliance.
• The appliance is designed exclusively for private use and for the envisaged purpose. This appli-ance is not fit for commercial use.
• The appliance is only to be used as described in the user manual. Do not use the appliance for any other purpose. Any other use is not intended and can result in damages or personal injuries.
• Operate the appliance only properly installed.
• Do not use it outdoors. Keep it away from sources of heat, direct sunlight and humidity.
• Do not operate the appliance without supervision.
• When not in use, for cleaning, user maintenance works or with disruption, switch off the appliance and disconnect the plug (pull the plug itself, not the lead) or turn off the fuse.
• The appliance and if possible the mains lead have to be checked regularly for signs of damage. If damage is found the appliance must not be used.
• For safety reasons, alterations or modifications of the appliance are prohibited.
• To ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

WARNING:
Do not allow small children to play with the foil. There is a danger of suffocation!

Special safety information for this unit

WARNING: Danger from electrical current! Contact with live leads or components can be fatal!

• The connection of the appliance must satisfy the relevant standards and regulations and may only be performed by an authorized specialist.
• The hob may not be used if the glass surface has cracks or is broken.
• The use of high-pressure cleaners or steam cleaners is prohibited. In-gress of liquids can lead to electric shock. Put the appliance never un-der water.

WARNING: Hot surface! Risk of burning!

• During operation the appliance and its accessible parts become hot. Special care must be taken to avoid touching heating elements. Chil-dren younger than 8 years must be kept away from the appliance.
• Let the appliance cool down before cleaning or maintenance.

WARNING: Risk of fire!

• Unattended cooking on cooking hobs with fats or oil can be dangerous and can be cause fires. NEVER attempt to extinguish a fire with water but turn the unit off and then cover the flames e.g. with a lid or a plate.
• CAUTION: The cooking process must be observed. A short cooking operation is to be observed continuously.
• Never store objects on the cooking surface.
• Use only hob guards designed by the manfucturer of the cooking apl-liance or indicated by the manfucaturer or the appliance in the instruc-tions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.
• The appliance is not intended for operation with an external timer or external remote-control system.
• Make sure that with installing adequate air circulations ensured and the ventilation slots are not blocked.
• Do not store any cleaning agents or flammable materials in the appli-ance or in the immediate vicinity.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and under-stand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children, unless they are older than 8 years and are supervised.
• Do not use harsh abrasive cleaners or sharp metal objects for cleaning the glass surface. The glass can be scratched or destroved.
• Do not try to repair the appliance on your own. Always contact an au-thorized technician. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons to avoid a hazard.

Transport and packaging

Transport the appliance

Secure the appliance sufficiently and protect it against weather during transport.

Unpacking the appliance

• Remove the appliance from its packaging.

• Remove all packaging material, such as foils, filler and cardboard packaging.
  Dispose of packaging materials that are no longer required in accordance with the locally applicable regulations.

• To prevent hazards, check the appliance for any transport damage.

• In case of damage, do not put the appliance into operation. Contact your distributor.

NOTE:

Production residue or dust may have collected on the appliance. We recommend cleaning the appliance according to chapter “Cleaning and maintenance”.

Appliance Equipment

Appliance overview

1. Control panel
2. Ø200 mm / 1800 W
3. Ø165 mm / 1200 W
4. Ø200 mm / 1800 W
5. Ø165 mm / 1200 W

Delivery scope

Installation material: 5x retaining clip, 5x fixing screw, 1x sealing tape

Installation

The hob is designed for installation in standard kitchen units.
Before installation, make a note of the serial number, which you will find on the rating label (hob base).

WARNING:

The installation and the connection to the main power may only be performed by an authorized specialist.

Risk of cutting injuries!

Beware of cutting edges on the appliance.

Recommendation, wear protective gloves when installing / transporting the appliance to avoid injury from possible sharp edges.

CAUTION:

• The worktop, the cabinet, veneers, plastic coat-ings, used adhesives etc. must be sufficient heat-resistant (min. 100°C).
• Do not mount the hob above cooling equipment, dishwashers and tumble dryers.

Safety distances

CAUTION:

Make sure that adequate air circulations ensured, and the ventilation slots are not blocked. Follow ap-propriate safety distances!

• The appliance must be installed so that heat can be dissipated. The ventilation openings must not be blocked (see illustration).
• The distance between the hob and the cooker hood must be at least as large as specified in the installation instructions for the hood. If the hood manufacturer’s instructions are missing or if highly flammable materials (e.g. wall cupboard) are in-stalled above the appliance, keep to the safety distance shown.
• A minimum distance must be left below the cut-out. No heat-sensitive objects (base unit, drawer, etc.) may be located in this area. Any existing side panels or drawers must be sawn out or re-moved accordingly.

Preparing the worktop for installation

CAUTION:
Before sawing, tape the outer edge of the cut-out with wide tape to avoid marks from the jigsaw on the worktop.

• The hob can be installed on a worktop with a thickness of between min. 30 mm and max. 40 mm, it must be horizontal and sealed on the wall side against overflowing liquids or moisture.
• The hob must be surrounded by at least 50 mm of worktop and run parallel to the front edge of the worktop.
• The cut surfaces (cut-out edges) must be sealed with special lacquer, silicone rubber or casting resin to prevent swelling due to moisture.
• The worktop in the area of the cut-out must be thoroughly clean and dry!

Worktop cut-out

Prepare the cut-out of the worktop according to the dimensional drawing.

Dimensions in mm

Installing the hob

CAUTION:

First place the front of the hob on a padded surface to prevent damage.

Step 1: Apply sealing tape

Before installing the hob, attach the enclosed, self-adhesive sealing tape (5) to the underside of the hob frame.

• Do not use silicone! Attach the seal to the under-side of the hob frame, leaving a gap of approx.’3 mm from the edge of the glass.
• Apply the seal around the entire circumference and cut off any excess material. Bring the two ends of the seal together so that they fit snugly.

Step 2: Fasten the retaining clips

Secure the hob with a total of 5 retaining clips to pre-vent it from slipping.

• Fasten the clips (1) to the holes (2) provided on the hob using the screws (3).

Step 3: Inserting the hob

Make sure that the distances to the cut-out are the same on all four sides and that the seal rests on the worktop.

• Place the hob in the prepared cut-out with the connection cable in front and the control panel facing forwards and press it firmly into place.
• Check that the hob is positioned properly and hor-izontally. If there is nothing more to correct, you can tighten the retaining clips from below to fix the hob in place.

Electrical connection

Information for the authorized expert!

WARNING:

• The installation to the mains supply must conform to the local standards and regulations.
• Connecting the appliance to a domestic power socket or using multiple sockets or extension ca-bles is not permitted.
• Improper connection may cause to an electric shock!
• Before connecting, ensure that the power supply corresponds with the information on the rating la-bel (hob bottom) and the wiring diagram.
• The appliance is suitable for three-phase and AC current.
• Select a suitable cord as mains cable, considering the connection type and rated power of the unit.
• Fix the mains cable in the tension relief.
• The electrical installation of the appliance should be equipped with an emergency switch, which switches off the whole appliance from the mains supply in an emergency. The distance between the contacts of the emergency switch must be at least 3 mm.
• Arrange the mains cable in such a way that it does not get in contact with any hot components of the appliance. Do not lead it over sharp edges or corners.

Connection plan

CAUTION:
The protective conductor MUST be connected to ter-minal PE

NOTE:

Connection point 3 and 5 are blind connections!

380-420V 2N~ 50-60Hz

H05 VV-F4G 2.5mm²
H05 GG-F4G 2.5mm²
H07 RN-F4G 2.5mm²

Startup / Operation

Before initial use

Cean the hob thoroughly. Use a cloth with warm wa-ter and a little special cleaner for glass ceramic hobs. Be sure to follow the instructions in the “Cleaning and maintenance” section.

Selecting appropriate cookware

CAUTION:
The cooking surface and the base of the cookware must always be clean and dry.

Wrong!

Correct! To save time and energy!

The cookware base is fully resting, and the lid closes properly.

Correct operation of the sensor buttons

The appliance is operated via touch buttons at the control panel.

• The buttons react to the slightest touch. You do not need to apply any pressure.
• The appliance reacts best when touching the but-tons with the fingertips and with dry hands.
• Once a touch has been registered, a brief beep will sound.
• Ensure that the control panel is always clean and dry. Objects or a small liquid film can impair oper-ation.

Operating overview

Function buttons

safety child lock
M7| Button to activate the timer function
M8| Reduce the power level and time setting
M9| Keep pressing the button for approx. 3 sec-onds to switch the appliance on/off

Digital displays

1. Display of power level, residual heat, etc.
2. Display of power level, residual heat, etc.
3. Display of power level, residual heat, etc.
4. Display of power level, residual heat, etc.
5. Display of timer setting, child lock, etc.

Power level settings

The settings below are guidelines only. The exact setting depends on various factors, such as your cookware and the amount you are cooking. Basically, the settings are empirical values → use, observe, ad-just, learn!

butter, and foods that burn quickly – gentle simmer-ing – slow warming
3 – 4|   – reheating – rapid simmering – cooking rice
5 – 6|   – pancakes
7 – 8|   – sautéing – cooking pasta
9|   – stir-frying – searing – bringing soup to the boil – boiling water

Switching a cooking zone on/off

After connection to the power supply, a signal tone sounds and all displays light up briefly.

• Place suitable cookware on the respectively cook-ing zone.

• Switch the appliance on using button (M9). All displays show [–].

• Select the cooking zone to be used with the re-spective button (M1) – (M4), the corresponding display flashes.

• Set a power level from 1 to 9 using buttons (M5) and/or (M8). – If you do not select a power level within one minute, the hob switches off automatically.
  – You can change the power level at any time during cooking.

• To switch off a cooking zone, select the cooking zone again and set the power level back to 0.

Residual heat indicator

WARNING: Risk of burns!

Do not touch the cooking zones while the residual heat indicator lights up.
After switching off the cooking zone, the residual heat of the corresponding zone is indicated with [H]. This warns against touching the zone.

Automatic boiling

This function automatically switches from high power for boiling/heating to the previously selected lower power for further cooking.

• Set the power level for the desired zone to 9 and press the button (M5), the corresponding zone display shows [A] and [9] alternately.
• Within the next 30 seconds, select the lower power level required for you to continue cooking.

The table below shows the cooking time (min) for each power level (PL):

NOTE:

When changing the power level, the elapsed time is automatically included in the corresponding cooking time for the new power level.

Safety child lock

The appliance is equipped with a locking function to prevent unintentional operation.

• Keep pressing the button (M6) for approx. 3 sec-onds to activate (deactivate) the safety child lock.

The timer display indicates activation with [Lo]. All buttons, except the power button are locked for operation.

When the timer function is active, the timer display alternately shows the remaining time and [Lo].

Timer function

General information

• You can use the timer to automatically end the cooking process on one or more zones after a preset time.
• The timer can be set between 1 and 99 minutes. As long as the minute display flashes in the timer display, the setting can be overwritten.
• A red dot next to the power level indicates that a timer has been set for this zone.
• The power level can be corrected at any time without changing the time setting.
• The timer function is cancelled when the appli-ance is switched off.

Using the timer to switch off one cooking zone

• Select the cooking zone that is already in opera-tion and for which you want to set the timer.
• Press the button (M7) for the timer. The timer dis-play lights up [00].
  Set the time using buttons (M5) and/or (M8).

The timer display shows the remaining time.

Using the timer to switch off several cooking zones

• Do the timer setting for several cooking zones as described under “Using the timer to switch off one cooking zone”.

The timer display shows the remaining time of the cooking zone for which the shortest maturity was se-lected. The cooking zone can be recognized by the flashing dot next to the power level.

When the operation period of this cooking zone is elapsed, the display shows the remaining time of the cooking zone for which the next shortest maturity was selected.

NOTE:
You can display the remaining cooking time of an-other cooking zone at any time. To do this, select the corresponding cooking zone.

Once the set time has elapsed, the cooking mode switches off automatically, a signal tone sounds and the timer display shows [00].

Cancelling the timer setting prematurely

• Select the required cooking zone for which you want to cancel the timer.
• Press the button (M7) for the timer. The timer dis-play flashes.
• Reset the timer setting to 0.

Overflow protection

If liquids run over one or more buttons on the control panel for more than 10 seconds during operation, the heating process is automatically interrupted, and the appliance switches to the off state.

• Caution! Allow the appliance to cool down before wiping up the liquid.
• Restart the operation.

Overheating protection

A temperature sensor monitors the interior of the ap-pliance. In the event of overheating, the heating pro-cess s is automatically interrupted to prevent dam-age.

Safety switch-off

The automatic switch-off is a protective function for your appliance. If a cooking zone is in operation for a long time and you do not make any entries on the control panel, the safety switch-off is activated.
The standard switch-off times (hrs) for the different power levels (PL) can be found in the table below:

Switching off the appliance

• Once the cooking process is complete, switch off the appliance using the button (M9).

Energy saving tips

Information to reduce the environmental effect of cooking (acc. VO (EU) No. 66/2014 appendix I, No. 2)

• Use pans and pots with flat floors. Uneven floors increase the energy consumption. The diameter of the pot and pan floors should be according to the size of the cooking zone, or bigger.
• Pans and pots, which are too small on the cook-ing zone leads to energy losses. Note: Dishes producer partly indicate the upper pot diameter. It is usually larger than the diameter of the pot floor.
• Use a small pot for small quantities. A large pot, which is only slightly filled, required a lot of en-ergy.
• Use as little water as possible. This saves energy. Vegetables retain their vitamins.
• Always close pots with a suitable lid. When cook-ing without lid you need four times more energy. When using glass lids, more energy can be saved because you can see into the pot without open the lid.
• Use a quick cooker to clearly reduce the cooking time and save energy.
• After boiling or frying, switch off the used cooking zones to a smaller power level.
• Use the residual heat of the pan, the pot and the food. Switch off the cooking zones 5-10 minutes before cooking time.

Cleaning and maintenance

WARNING:

• Always switch off the appliance completely before cleaning and maintenance work and disconnect it from the power supply if necessary.
• Allow the unit to cool down before cleaning.
• Do not use steam cleaners for cleaning the appli-ance; moisture could enter electrical components. Risk of electric shock! Hot steam could damage the plastic parts.
• Never use flammable substances, such as thin-ner, kerosene, gasoline or acids for cleaning.
• The unit must be dry before restarting operation.

CAUTION:

• Do not use a wire brush or other sharp, abrasive items.
• Do not use harsh abrasive cleaners or sharp metal objects for cleaning the glass surface. The surfaces can be scratched or destroyed.
• Always consider the application and safety notes of the detergent.

Cleaning the hob

• Remove food residues while the hob is still warm with a damp cloth or paper towel.
• Wash the hob with a soft sponge and a little water and dry thoroughly with a soft cloth.

Cleaning agent for glass ceramic surfaces

For burnt-on residues, help yourself to products from the specialist departments of stores.

ing sponge for glass ceramic
Pools and lime depo-sits| Apply warm vine-gar and wipe off with a dry cloth or use special clean-ing agent.| Special clean-ing agent for glass ceramic
Sugar, melted alu-minum, or plastic| Remove by using a glass ceramic scraper.| Special clean-ing agent and scraper for glass ceramic

Troubleshooting

Before you contact an authorized specialist

In the event of some malfunctions, the hob automati-cally goes into protection mode and the corresponding error code is displayed.

Problem / possible cause / action

Appliance does not work
Check the power supply / main fuse.

Control panel does not react or only very difficult
” – Child safety lock is activated.
– Clean and dry the operating surface.”

Cracking noises during operation
May be caused by the cookware construction (lay-ers of different metals).

Ventilation noise after switching off
No failure, the fan continues to run for some time for overheating protection.

• Error code E1: Display board is not receiving the signal from the power sup-ply board.
• Error code E2: Power supply board is not re-ceiving the signal from the dis-play board.
• Error code E3:  Relay failure

Disconnect the power supply briefly. If the fault occurs again, con-tact a specialist!

NOTE:

If a problem persists after following the steps above, contact your distributor or an authorized technician.

Technical data

Electrical connection……………………………………..
Connection voltage: …………380-420V 2N~ 50-60Hz
Connection power: ……………………………..6000 W
Fuse protection: ……………………..….………2 x 16 A

Dimension / Weight……………….…….………………..
Hob (HxWxD): ……………………5.0 x 58.0 x 51.0 cm
Worktop cut-out (WxD): …………………56.0 x 49.0 cm
Net weight: ….……………………………approx. 7.7 kg

The right to make technical and design modifications during continuous product development remains re-served.
This appliance has been tested according to all rele-vant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Meaning of the “Dustbin” symbol

This symbol indicates that this product must not be disposed of with household waste in accordance with the Waste Electrical and Electronic Equipment Di- rective (2012/19/EU) and national legislation.
Improper handling of waste electrical and electronic equipment can have negative effects on the environ-ment and human health due to potentially hazardous substances that are often contained in waste electri-cal and electronic equipment.

Consumers are legally obliged to dispose of electrical and electronic appliances separately from unsorted municipal waste at the end of their service life. By disposing of this product properly, you are also con- tributing to the effective utilization of natural re-sources.
Information on collection points for old appliances can be obtained from your local authority, the public waste disposal authority, an authorized body for the disposal of old electrical and electronic appliances or your waste collection service.

This product must be returned to a designated collec-tion point. This can be done, for example, by return-ing it when purchasing a similar product or by hand-ing it in at an authorized collection point for the recy-cling of old electrical and electronic equipment. The return of old appliances is free of charge. Your dealer and contractual partner is also obliged to take back the old appliance free of charge.

Before disposing of the product, remove all batteries and rechargeable batteries as well as all lamps that can be removed without destroying them.

Please note that you are responsible for deleting per-sonal data from the product to be disposed of.

WARNING:
Remove or destroy any existing latches and bolt locks when you take the appliance out of operation or dispose of it.

Information to professional users for disassembly (acc. VO (EU) No. 66/2014 appendix I, No. 2)

Information for non-destructive disassembly for maintenance purposes

• A further disassembly for maintenance purposes by the user is not provided. Do not disassemble the unit.
• For repair and replacement of defective parts, please contact our customer service.
• Accumulators are not included.

Information for disassembly in terms of recycling, re-covery and disposal at the end of the life of the appli-ance

• The disassembly of appliances with a gas con-nection should only be carried out by a licensed gas and water installer.
• The disassembly of appliances with electrical con-nections should be carried out by a licensed elec-trician.
• For the recycling and recovery of resources give the appliance to:
  – a communal collection point waste disposal authority,
  – a dedicated disposal company, offering a re-turn system,
  – a resident electric trader, who voluntary with-draws electrical appliances.

EU Product data sheet

Product information for domestic electric hobs according to EU 66/2014

Applied measurement and calculation method according to EN 60350-2

Specifications:

• Model: HAUSHALTS-KOCHFELD EBK 7940

• Type: Household Hob

• Installation Material: 5x Fastening Clamp, 5x Fastening Screw, 1x Sealing Tape

Frequently Asked Questions (FAQ)

Q: What should I do if the hob displays an error code?

A: In case of malfunctions, the hob may enter a protection mode showing an error code. Refer to the user manual for troubleshooting steps or contact customer service.

References

• Bomann Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>