AUTOSOLO 415849 Wheel Alignment Toe Plates User Guide
- June 1, 2024
- AUTOSOLO
Table of Contents
AUTOSOLO 415849 Wheel Alignment Toe Plates User Guide
The Wheel Alignment Toe Plates user manual will guide you through the proper setup and usage of the product. Please read the instructions carefully before using the Toe Plates for wheel alignment.
PRODUCT OVERVIEW
Introduction
The Toe Plates are designed to measure the toe angle of the wheels, which is
the angle when viewed from the top.
Professional Service
For wheel alignment adjustments, it is recommended to seek the assistance of a
qualified technician.
Package Contents
When unpacking the product, please verify that all the following parts are
included. If any parts are missing or broken, do not proceed with assembly or
usage. Instead, contact AutoSolo using the contact details provided on the
back cover of this manual for assistance.
The package includes:
• 2x Toe Plate • 2x Measuring Tape • User Manual • 1x Storage Bag
GENERAL SAFETY INSTRUCTIONS
Work Area Safety
- Keep the work area clean and dry to avoid accidents.
- Children should not handle this product.
- Store idle equipment in a dry location to prevent rust and keep it out of reach of children.
Avoid Impairment
- Do not use this product while under the influence of alcohol or drugs.
- Be aware of any impairments caused by prescription medications. If in doubt, do not use the equipment.
GENERAL SAFETY INSTRUCTIONS
Eye Protection and Proper Attire
- Wear ANSI approved safety impact eye glasses.
- Use non-skid footwear or safety shoes.
- Avoid loose clothing or jewelry that can become caught in moving parts.
- Protect long hair by wearing a covering.
- Roll up long sleeves above the elbows.
Compliance with Industrial Standards
- Industrial applications must follow OSHA requirements.
Balance and Alertness
- Maintain proper footing and balance to prevent accidents.
- Stay alert and focused while using the equipment.
Inspection and Maintenance
- Before using the product, carefully inspect it for any damage or worn parts.
- Replace or repair damaged parts immediately.
- Regularly service and maintain the equipment for safety.
Proper Use
- se the product only for its intended purpose.
- Do not use a small tool or equipment for tasks that require a larger industrial tool.
- Follow the vehicle manufacturer’s manual or consult a qualified technician for specific alignment tolerances.
Working Under Vehicles
- Never work underneath a vehicle without using additional safety support devices, such as jack stands, to secure the vehicle.
OPERATING INSTRUCTIONS
Specific Product Warnings and Precautions
Positioning the Toe Plates
Place the Toe Plates on a dry, flat, and level surface. Avoid using the Toe
Plates on uneven surfaces or surfaces covered with ice, grease, oil, or any
other substances that may cause tipping or sliding.
Safety Precautions
a) Turn off the engine, engage the parking brake, and block the rear
tires before using the Toe Plates. Do not attempt to use the Toe Plates while
the engine is running.
b) Carefully exit the vehicle and block the rear tires with wheel chocks
or blocks of wood to prevent the vehicle from rolling during service.
Vehicle-Specific Alignment Tolerance
Consult the vehicle manufacturer’s manual or a qualified technician to
determine the acceptable degree of tolerance for front-end wheel alignment
specific to the make and model of the vehicle being tested.
Safety Support Devices
Never work underneath a vehicle without using additional safety support
devices such as jack stands to ensure proper support and prevent accidents.
The Toe Plates are not designed to be used with jack stands.
OPERATING INSTRUCTIONS
Toe Alignment Measuring
Understanding “Toe”
Toe refers to the angle of the wheels when viewed from the top (refer to
Figure A). When the wheels on the same axle point inwards, it is called
“Toe in”. When the wheels on the same axle point outwards, it is
called “Toe out”.
Preparation
Ensure that the vehicle’s steering wheel is centered. If the vehicle has hub
caps, remove them before proceeding.
Align Plates
Place both toe plates against the wheels, ensuring that the largest surface
area of the plates is in contact with the wheels.
Add Measuring Tapes
Extend the measuring tape underneath the vehicle for approximately 6-7 feet.
Move to the opposite side of the car where the tip of the measuring tape is
and attach it to the toe plate using any available slots. Ensure that both
plates are properly seated in its entirety against the rim of the wheel.
Measure Toe
Return to the original side where the body of the measuring tape is located.
Unlock the tape measures and insert them into the slots. Do NOT lock the tape
measures; leaving them unlocked will provide the necessary tension. Gently let
them hang and take note of the measurements
Calculate Toe
Subtract the front-vehicle tape measurement from the rear-vehicle tape
measurement to obtain the total toe of the axle. A larger measurement on the
front side indicates toe out, while a larger measurement on the rear side
indicates toe in. Use the conversion chart to convert distance to degrees.
Example:
Front-vehicle measurement: 64.875″
Rear-vehicle measurement: 65″
Total toe: IN .3°
Alignment Assessment:
For most vehicles, a .1-.3 degree toe in is ideal. The specific tolerance
limits for toe-in/out angles should be obtained from the vehicle
manufacturer’s specifications or consulting a qualified technician familiar
with your vehicle. it is strongly recommended to have the front end wheel
alignment serviced by a qualified technician. They will have the expertise and
tools required to make the necessary adjustments.
Please note that for precise alignment specifications and tolerance differences specific to the vehicle make and model being tested, it is advisable to consult the vehicle manufacturer’s manual and/or a qualified technician. They can provide the most accurate information regarding alignment tolerances for your specific vehicle
INSPECTION, MAINTENANCE & CLEANING
To ensure the optimal performance and longevity of your Toe Plates, please
follow these inspection, maintenance, and cleaning instructions:
Regular Inspection: Before each use, thoroughly inspect the Toe Plates
for any signs of damage or wear that may affect their safe operation. Pay
attention to the following:
- Cracks or fractures on the plates
- Dents or deformations that may affect their accuracy
- Any loose or missing parts If any issues are detected, immediately discontinue the use of the Toe Plates and contact a qualified technician for inspection and servicing. DO NOT use damaged equipment.
Maintenance : To maintain the functionality and accuracy of the Toe Plates, we recommend the following maintenance practices:
- Store the Toe Plates in a dry and clean environment, protected from extreme temperatures and humidity.
- Avoid subjecting the Toe Plates to excessive force, impacts, or rough handling.
- Do not modify or alter the Toe Plates in any way, as it may affect their performance and accuracy.
- Lubricate any moving parts or mechanisms as recommended by the manufacturer, if applicable.
Cleaning: To keep the Toe Plates in optimal condition, follow these cleaning guidelines:
- Keep the Toe Plates free from oil, grease, or other contaminants. These substances can affect the accuracy of the measurements.
- Use a mild detergent and a damp cloth to clean the Toe Plates. Gently wipe the surfaces to remove any dirt or debris.
- DO NOT use flammable or combustible solvents for cleaning purposes, as they can damage the Toe Plates or pose a safety hazard.
- Allow the Toe Plates to dry completely before storing them to prevent the accumulation of moisture.
By following these inspection, maintenance, and cleaning instructions, you can ensure that your Toe Plates remain in good working condition and provide accurate wheel alignment measurements
WARRANTY
Limited 1-Year Replacement Warranty
AutoSolo warrants that the Wheel Alignment Toe Plates will be free from
manufacturing defects for a period of one year from the date of its original
retail purchase.
Coverage Period
This warranty is valid for one year from the date of its original retail
purchase. It is non-transferable, and the coverage terminates if the product
is sold or transferred to another party.
Manufacturer’s Responsibility
If the product is found to have a manufacturing defect within the warranty
period, when used as directed, the manufacturer will, at its sole discretion,
either repair the defective product by requesting the customer to return it or
replace the product. The replacement product will be covered for the remaining
period of the original warranty.
Exclusions
This limited warranty does not cover problems or damages arising from:
(a) Abuse, misuse, neglect, or accident.
(b) Alteration of the product or any component thereof.
(c) Shipping.
(d) Improper installation, operation, or maintenance.
(e) Use of parts from another manufacturer.
(f) Problems or damages due to natural disasters, force majeure events,
or acts of God.
Void Warranty
The warranty is void if the serial number or date of purchase is illegible or
if the warranty claim is not made in a timely manner.
Limitation of Liability
Except as expressly provided herein, there are no other warranties, expressed
or implied, including but not limited to warranties of merchantability or
fitness for a particular purpose. To the extent permissible by applicable law,
the manufacturer shall not be liable under any legal theory for indirect,
incidental, special, consequential, or similar damages, including lost
profits, damage to person or property, loss of use, or inconvenience. Your
sole remedy shall be limited to the repair or replacement of the product at
the manufacturer’s discretion.
Making a Warranty Claim
To be eligible for service under this warranty, please follow these
steps:
- Within 30 days of discovering a manufacturing defect covered by the warranty, contact us at support@autosolotools.com.
- Upload a proof of purchase receipt along with the warranty request.
- Note that returns received 30 days or more after the claim file has been opened may be refused and returned at your expense.
- For further assistance regarding warranty claims, please refer to the contact details provided on the back cover of this manual.
Visit our website: autosolotools.com For
technical questions
please email or call us at:
support@autosolotools.com
415.849.0275
©AutoSolo® 2023 All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of AutoSolo® 2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>