AUTOSOLO Universal Wheel Clamp and Magnetic Adapter User Guide
- June 1, 2024
- AUTOSOLO
Table of Contents
AUTOMOTIVE TURN TABLES
USER GUIDE
support@autosolotools.com
autosolotools.com
Universal Wheel Clamp and Magnetic Adapter
The user manual for the Wheel Alignment Turn Plates aims to provide clear
instructions for easy setup and safe operation of the turn plates.
Please read the instructions carefully before using the Turn Plates for wheel
alignment.
PRODUCT OVERVIEW
1.1 Introduction
Turn Plates are a reliable and essential tool for assessing and adjusting
front-end wheel alignment on compact cars and lightweight trucks.
Designed to provide accurate readings, these plates help identify whether
alignment adjustments are necessary. With a user-friendly setup and
compatibility with various vehicle models, the turn plates are a must-have for
technicians and enthusiasts seeking precise alignment measurements for optimal
vehicle performance.
1.2 Purpose
The Turn Plates are designed to indicate whether the front-end wheel alignment
of a compact car or lightweight truck requires adjustment. Proper alignment is
crucial for optimal vehicle performance, tire wear, and fuel efficiency.
1.3 Qualified Technician Recommendation
If the Turn Plates indicate a need for front-end wheel alignment adjustment,
it is highly recommended to have a qualified technician perform the service.
Qualified technicians possess the knowledge and expertise to accurately adjust
the alignment, ensuring precise results and preventing any potential damage to
the vehicle.
1.4 Package Contents
When unpacking the product, please verify that all the following parts are
included. If any parts are missing or broken, do not proceed with assembly or
usage. Instead, contact AutoSolo using the contact details provided on the
back cover of this manual for assistance.
The package includes:
2x Turn Plates: These plates are specifically designed for accurate wheel
alignment measurements.
2x Thrust Blocks: The thrust blocks assist in stabilizing the vehicle during
the alignment process.
2x Transition Bridges: These bridges provide a smooth transition for driving
the vehicle onto the turn plates.
1x User Manual: This comprehensive manual provides detailed instructions for
proper setup, operation, maintenance, and warranty information.
GENERAL SAFETY INSTRUCTIONS
2.1 Work Area Safety
- Keep the work area clean and dry to avoid accidents.
- Children should not handle this product.
- Store idle equipment in a dry location to prevent rust and keep it out of reach of children.
2.2 Avoid Impairment
- Do not use this product while under the influence of alcohol or drugs.
- Be aware of any impairments caused by prescription medications. If in doubt, do not use the equipment.
2.3 Eye Protection and Proper Attire
- Wear ANSI approved safety impact eye glasses.
- Use non-skid footwear or safety shoes.
- Avoid loose clothing or jewelry that can become caught in moving parts.
- Protect long hair by wearing a covering.
- Roll up long sleeves above the elbows.
2.4 Compliance with Industrial Standards
- Industrial applications must follow OSHA requirements.
2.5 Balance and Alertness
- Maintain proper footing and balance to prevent accidents.
- Stay alert and focused while using the equipment.
2.6 Inspection and Maintenance
- Before using the product, carefully inspect it for any damage or worn parts.
- Replace or repair damaged parts immediately.
- Regularly service and maintain the equipment for safety.
2.7 Proper Use
- Use the product only for its intended purpose.
- Do not use a small tool or equipment for tasks that require a larger industrial tool.
- Follow the vehicle manufacturer’s manual or consult a qualified technician for specific alignment tolerances.
2.8 Working Under Vehicles
- Never work underneath a vehicle without using additional safety support devices, such as jack stands, to secure the vehicle.
OPERATING INSTRUCTIONS
3.1 Specific Product Warnings and Precautions
3.1.1 Weight Capacity and Dynamic Loading
- Do not exceed the weight capacity of the turn plates, which is 3,000 lbs. or 1.5 Tons per pair.
- Be cautious of dynamic loading caused by sudden weight drops, as it may briefly exceed the load capacity. Handle weights carefully to prevent any accidents.
3.1.2 Proper Surface and Positioning
-
Position the turn plates on a dry, flat, and level surface capable of supporting the weight of both the turn plates and the vehicle.
-
Ensure that you have a level surface available before starting the setup.
Uneven surfaces can affect the accuracy of alignment readings. -
Avoid uneven or slippery surfaces that may cause the turn plates to tip or slide during operation.
3.2 Before Starting
3.2.1 Alignment Plate and Weight Distribution
For optimal performance, it is recommended to use an alignment plate, such as
the ASWG008, under each wheel to distribute the weight evenly.
3.2.2 Tire Pressure
Ensure that the tire pressure is set according to the vehicle specifications
to achieve accurate alignment results.
3.2.3 Wheel Positioning and Locking
Before lowering the vehicle onto the turn plates, make sure the wheels are
facing straight forward and locked. This prevents the wheels from rolling off
the turn plates during the alignment process. For older cars, a brake pedal
stop can be used for this purpose.
3.3 Set-up
3.3.1 Place the Turn Plates
Position the turn plates on the ground, ensuring they are aligned parallel to
each other and perpendicular to the vehicle’s direction of travel.
The scale plates
should face towards the front of the vehicle.
3.3.2 Lock the Turn Plates
Engage the locking mechanism on each turn plate to secure them in place.
This prevents any movement during the alignment process.
3.4 Lowering the Car
3.4.1 Wheel Positioning and Locking
Before lowering the vehicle, ensure that the wheels are still facing straight
forward and locked to prevent them from rolling off the turn plates. For older
cars, a brake pedal stop can be used for this purpose.
3.4.2 Wheel and Plate Alignment
Ensure all wheels and alignment plates are aligned with each other and facing
forward.
3.4.3 Proper Lowering Procedure
Lower the car onto the turn plates carefully. Avoid driving onto the turn
plates directly.
3.4.4 Guiding the Vehicle onto the Turn Plates
If driving onto the plates is necessary, enlist the help of another person to
act as a visual guide when driving the vehicle onto the turn plates.
3.4.5 Driving Speed and Vehicle Positioning
Drive onto the turn plates at the slowest speed possible. Stop the vehicle
when the front tires are centered with the scale pin
3.4.6 Suspension Settling
After lowering the vehicle onto the plates, settle the suspension by working
the wheels back and forth and pushing down on the car’s front end a few times.
3.4.7 Engine Shutdown and Rear Tire Blocking
Turn off the engine and engage the parking brake. Place the thrust blocks onb
each turn plate, aligning them with the vehicle’s tire tread. These blocks
will help stabilize the vehicle during the alignment process.
3.4.8 Transition Bridge
If necessary, place the transition bridge in front of the turn plates. This
bridge assists in smoothly guiding the vehicle’s tires onto the turn plates.
3.5 Alignment Procedure
-
Begin by removing the two locking pins from each Turn Table to ensure freedom of movement.
-
Turn the steering wheel of the vehicle as far to the right as possible.
While holding the steering wheel in this position, have another person take an accurate reading from the scale plate of each turn table. Make sure to measure the readings in degree increments. -
Compare the readings taken from both turn plates.
-
Next, turn the steering wheel of the vehicle as far to the left as possible.
Again, have another person take accurate readings from the scale plate of each turn table in degree increments. -
Compare the readings obtained from the scale plates with the recommended alignment specifications provided by the vehicle manufacturer or a qualified technician.
-
Assess the alignment based on the differences between the actual and desired values.
3.5.1 Alignment Assessment
- For most vehicles, if the comparison readings from the Scale Plate differ by only 0 to 5 degrees, it indicates that no front wheel alignment adjustment is necessary. In such cases, the alignment is within an acceptable range.
- However, if the comparison readings differ by more than 5 degrees, it is strongly recommended to have the front end wheel alignment serviced by a qualified technician. They will have the expertise and tools required to make the necessary adjustments.
- Please note that for precise alignment specifications and tolerance differences specific to the vehicle make and model being tested, it is advisable to consult the vehicle manufacturer’s manual and/or a qualified technician. They can provide the most accurate information regarding alignment tolerances for your specific vehicle.
3.6 Safely Removing the Vehicle
To remove the vehicle from the turn plates, lock the turn plates and reverse
the vehicle slowly. Ensure that the tires are aligned with the transition
bridge (if used) for a smooth exit.
3.6.1 Turn Plate Lock Release
Before storing the turn plates, engage the locking mechanism on each plate to
allow for easy removal and storage.
CLEANING, INSPECTION & LUBRICATION
Cleaning: After each use, clean the turn plates using a mild detergent
and water. Avoid using abrasive cleaners that may damage the surface of the
plates.
Inspection: Regularly inspect the turn plates for any signs of damage or
wear. Pay attention to the pins, scale plates, and locking mechanisms. If any
components are damaged or not functioning properly, discontinue use and
replace the damaged parts before proceeding with further alignments.
Lubrication: Apply a light coat of lubricant to the moving parts of the
turn plates periodically to ensure smooth operation. Use a lubricant
recommended by the manufacturer for best results.
WARRANTY
Limited 1-Year Replacement Warranty
AutoSolo warrants that the Wheel Alignment Turn Plates will be free from
manufacturing defects for a period of one year from the date of its original
retail purchase.
Coverage Period
This warranty is valid for one year from the date of its original retail
purchase. It is non-transferable, and the coverage terminates if the product
is sold or transferred to another party.
Manufacturer’s Responsibility
If the product is found to have a manufacturing defect within the warranty
period, when used as directed, the manufacturer will, at its sole discretion,
either repair the defective product by requesting the customer to return it or
replace the product. The replacement product will be covered for the remaining
period of the original warranty.
Exclusions
This limited warranty does not cover problems or damages arising from:
(a) Abuse, misuse, neglect, or accident.
(b) Alteration of the product or any component thereof.
(c) Shipping.
(d) Improper installation, operation, or maintenance.
(e) Use of parts from another manufacturer.
(f) Problems or damages due to natural disasters, force majeure events, or
acts of God.
Void Warranty
The warranty is void if the serial number or date of purchase is illegible or
if the warranty claim is not made in a timely manner.
Limitation of Liability
Except as expressly provided herein, there are no other warranties, expressed
or implied, including but not limited to warranties of merchantability or
fitness for a particular purpose. To the extent permissible by applicable law,
the manufacturer shall not be liable under any legal theory for indirect,
incidental, special, consequential, or similar damages, including lost
profits, damage to person or property, loss of use, or inconvenience. Your
sole remedy shall be limited to the repair or replacement of the product at
the manufacturer’s discretion.
4.2 Making a Warranty Claim
To be eligible for service under this warranty, please follow these steps:
- Within 30 days of discovering a manufacturing defect covered by the warranty, contact us at support@autosolotools.com.
- Upload a proof of purchase receipt along with the warranty request.
- Note that returns received 30 days or more after the claim file has been opened may be refused and returned at your expense.
- For further assistance regarding warranty claims, please refer to the contact details provided on the back cover of this manual.
Visit our website: autosolotools.com
For technical questions please email or call us at:
support@autosolotools.com
415.849.0275
©AutoSolo ® 2023
All rights reserved.
No portion of this manual or any artwork
contained herein may be reproduced in any shape or form
without the express written consent of AutoSolo® 2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>