DORMAN 924-730 Ignition Lock Cylinder Instruction Manual

DORMAN 924-730 Ignition Lock Cylinder

INSTRUCTION MANUAL

ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

REMOVAL/INSTALL OF IGNITION LOCK CYLINDER

(924-730) Ford 1996–90, Lincoln 1998–93, Mercury 1995–90

PLEASE WEAR SAFETY GLASSES!

Removal Instructions

STEP 1: Disconnect battery
STEP 2: Rotate lock cylinder to the run position.

STEP 3: Push a small screwdriver or small drift punch in hole in trim shroud under lock cylinder. Push retaining pin in while pulling on lock cylinder to remove from column.

Disclaimer:

Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature.

©2018 Dorman Products, Inc.
No reproductions in whole or in part without prior written approval.

924-730 INSTALL/REMOVAL INSTRUCTIONS: IGNITION LOCK CYLINDER

ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

Installation Instructions

STEP 1: Install lock cylinder by rotating the new lock to the run position and pressing down on retaining pin.

STEP 2: Insert lock into column. Ensure that cylinder is fully seated and aligned in interlocking washer before turning key to the off position. This will enable the lock retaining pin to extend into cylinder housing.
STEP 3: Rotate new lock cylinder using key to ensure proper operation in all positions.
STEP 4: Reconnect battery.

We appreciate your opinions regarding this product!

Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product.
1-800-523-2492

Disclaimer:

Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature.

©2018 Dorman Products, Inc.
No reproductions in whole or in part without prior written approval.

Specifications:

• Model: 924-730
• Product: Ignition Lock Cylinder

Product Usage Instructions

Removal Instructions

1. Disconnect the battery.
2. Rotate the lock cylinder to the run position.
3. Push a small screwdriver or small drift punch into the hole in the trim shroud under the lock cylinder. Push the retaining pin in while pulling on the lock cylinder to remove it from the column.

Installation Instructions

1. Install the lock cylinder by rotating the new lock to the run position and pressing down on the retaining pin.
2. Insert the lock into the column. Ensure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the off position, allowing the lock retaining pin to extend into the cylinder housing.
3. Rotate the new lock cylinder using the key to ensure proper operation in all positions.
4. Reconnect the battery.

FAQ

Q: What should I do if I encounter difficulties during installation?

A: Please contact our Technical Assistant at 1-800-523-2492 for any challenges or suggestions regarding the installation or operation of this product.

Q: Can I install this product without a service manual?

A: It is recommended to refer to the appropriate shop manual for your vehicle for specific service procedures. If you lack the skill, it is advised to seek the services of a qualified technician for installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>