DORMAN 924-714 Ignition Lock Housing Instruction Manual

DORMAN 924-714 Ignition Lock Housing

Product Specifications

• Product Name: 924-714 Ignition Lock Housing
• Manufacturer: Dorman Products, Inc.
• Model Number: 924-714

Product Usage Instructions

Passlock Relearn Without Tool:

1. STEP 1: Turn the key to the ON position with the engine off.
2. STEP 2: Attempt to start the engine, then release the key to ON. The vehicle will not start.
3. STEP 3: Observe the SECURITY light. After approximately 10 minutes, the light will turn OFF.
4. STEP 4: Turn OFF the ignition and wait five seconds.
5. STEP 5: Repeat Steps 1 to 4 two more times for a total of 3 cycles/30 minutes. The vehicle will automatically learn the Passlock Sensor Data Code the next time the ignition switch is turned from OFF to ON.
6. STEP 6: Turn the vehicle off and then verify the vehicle is able to start.
7. STEP 7: DTCs will clear themselves after 100 ignition cycles.

Need Help?

If you require assistance, please contact our Technical Support team at 866-933-2911">1-866-933-2911 . Dorman Products, Inc. Corporate Office and Customer Service: 800-523-2492">1-800-523-2492

Frequently Asked Questions

• Q: What should I do if the SECURITY light does not turn off after approximately 10 minutes?
  • A: If the SECURITY light does not turn off as expected, please ensure that you have followed each step correctly. If the issue persists, contact our Technical Support team for further assistance.
• Q: Can I perform the Passlock relearn procedure with the key removed from the ignition?
  • A: No, it is important not to remove the key from the ignition during the Passlock relearn procedure. Doing so will require restarting the process from the beginning.

Product Overview

After installation is complete, the Passlock sensor must be reprogrammed.

There are two methods to perform the programming procedure:

• A 10-minute procedure which requires a Tech2 tool or scanner and a Techline terminal, which will guide you through the procedure.
• A 30-minute procedure which does not require the use of any tools.

Installation Instruction

IMPORTANT: Do not remove the key from the ignition during this procedure. If the key is removed, the procedure will have to be performed from the beginning.

• STEP 1:
  • Turn the key to the ON position with the engine off.
• STEP 2:
  • Attempt to start the engine, then release the key to ON. The vehicle will not start.
• STEP 3:
  • Observe the SECURITY light. After approximately 10 minutes, the light will turn OFF.
• STEP 4:
  • Turn OFF the ignition and wait five seconds.
• STEP 5:
  • Repeat Steps 1 to 4 two more times for a total of 3 cycles/30 minutes. The vehicle will automatically learn the Passlock Sensor Data Code the next time the ignition switch is turned from OFF to ON
• STEP 6:
  • Turn the vehicle off and then verify the vehicle is able to start.
• STEP 7:
  • DTCs will clear themselves after 100 ignition cycles.

BEFORE YOU BEGIN

• Always wear proper safety equipment when performing repairs.
• Ensure at your point of purchase that this part fits your exact vehicle configuration.
• Reference the appropriate service manual for your vehicle. If you do not have a service manual and do not have the training or experience to perform the necessary procedures correctly, seek the services of a qualified technician.

Contact

NEED HELP?

Please call our Technical Support team for assistance from our team of certified automotive experts. 1-866-933-2911

Dorman Products, Inc. Corporate Office and Customer Service: 1-800-523-2492. Disclaimer: It is impossible in these instructions to account for all possible circumstances or situations that you may experience when attempting to install this product. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>