DORMAN 599-212 Climate Control Module Instruction Manual

DORMAN 599-212 Climate Control Module

Product Specifications :

• Model Number: 599-212
• Function: Heated mirror/defrost button LED recalibration module
• Compatibility: Vehicles with heated mirror/defrost systems
• Installation: Requires connection to vehicle’s electrical system

Product Usage Instructions

Installation:

1. If installing for the first time:
2. Connect the module to the vehicle’s electrical system.
3. Follow the steps below for initial calibration.
4. If recalibration is necessary (e.g., after replacing an actuator):
5. Press and hold the AC and heated mirror/defrost buttons simultaneously until both LEDs illuminate (at least 15 seconds).
6. Release both buttons; the heated mirror/defrost button LED will start flashing.
7. Wait for the LED to stop flashing (about 1 minute) to complete recalibration.

Frequently Asked Questions (FAQ):

• Q: How do I know if the recalibration procedure was successful?
  A: The heated mirror/defrost button LED will stop flashing, indicating successful completion. Allow up to 1 minute for recalibration after the LED stops flashing.

• Q: Can this module be used in all vehicles with heated mirror/defrost systems?
  A: The module is compatible with vehicles equipped with heated mirror/defrost systems. Ensure proper installation for optimal performance.

TECH NOTES: INSTALLATION

ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully. This product is only designed to function properly on specific vehicle applications. Please verify that the vehicle requirements match the product specifications and application notes for this part.
Dodge Dakota 2004–01, Dodge Ram 1500 2005–02, Dodge Ram 2500 2005–02, Dodge Ram 3500 2005–02

If you are installing on the vehicle for the first time:

• STEP 1 : With the vehicle turned off:
  • Set fan speed to the “off” position (turn knob counter clockwise until it stops).
  • Set temperature to the full cold position (turn knob counter clockwise until it stops).
  • Set mode to “floor and panel with recirculation” position (turn knob counter clockwise until it stops).
• STEP 2: Install module and start the vehicle.
• STEP 3 : The heated mirror/defrost button LED will begin flashing.
• STEP 4 : When the heated mirror/defrost button LED stops flashing, this indicates the recalibration procedure has been completed successfully.
• NOTE : Allow up to 1 minute for recalibration.

If it is necessary to recalibrate the unit (ex. an actuator has been replaced):

• STEP 1 : With the vehicle turned off:

  • Set fan speed to the “off” position (turn knob counter clockwise until it stops).

  • Set temperature to the full cold position (turn knob counter clockwise until it stops).

  • Set mode to “floor and panel with recirculation” position (turn knob counter clockwise until it stops).

• STEP 2: Turn ignition to the “on” position.

• NOTE : DO NOT START VEHICLE!!!

• STEP 3 : Press and hold the “AC” and “heated mirror/defrost” buttons until both LEDs illuminate.

• NOTE : Hold both buttons for at least 15 seconds.

• STEP 4 : Once both LEDs have illuminated, release both buttons and the heated mirror/defrost button will begin flashing.

• STEP 5 : When the heated mirror/defrost button LED stops flashing, this indicates the recalibration procedure has been completed successfully.

• NOTE : Allow up to 1 minute for recalibration.

• STEP 6 : The vehicle can now be started and the module is ready to be used.

Disclaimer :
Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature.

Dorman Products, Inc.

• Corporate Office and Customer Service: 1-800-523-2492 ©2021
• No reproduction in whole or in part without prior written approval.
• 599-212_Tech-Note

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>