DORMAN 265-887 Transmission Oil Pan

Specifications :

• Product: 265-887 Transmission Oil Pan Adjustment tool
• Torque: 4 ft-lb (6 Nm)
• Includes: threaded fill plug, closed plug, overflow tube, guide
  tube, replacement filters

Product Usage Instructions:

Installing Threaded Fill Plug and Closed Plug:

1. Install the supplied threaded fill plug on the new transmission oil pan and torque to 4 ft-lb (6 Nm).
2. Install the transmission pan.
3. Fill the bread through the threaded fill plug. Use a transfer pump following OE instructions.
4. Adjust the position of the overflow tube using the adjustment tool.
5. After filling, remove the threaded fill plug and replace it with the supplied closed plug. The standpipe design will prevent fluid loss.

Installing Overflow Tube and Guide Tube:

1. Ensure that the arrows on the bottom of the overflow tube are aligned before installing it on the new transmission oil pan.
2. Install the overflow tube and guide tube by snapping them into place, and aligning the arrows on the overflow tube as needed.

Replacement Filters:

When replacing filters on the 265-887, use Dorman part number 265-887F. This part contains filters, a gasket, an overflow tube, a guide tube, a threaded fill plug, and an adjustment tool. The OE pan filters are not replaceable. The adjustment tool can be purchased separately using part number 265-887T.

To drain the transmission fluid, remove the drain plug from the pan. Insert the supplied adjustment tool (265-887T). The end of the tool will line up with the #1 on the bottom of the pan. Rotate the tool counterclockwise so the end of the tool lines up with the #4 on the bottom of the pan. (Positions #2 and

3 will not be used.)

Remove the tool and the transmission fluid will drain out. Once it has fully drained, remove the pan from the vehicle.

INSTALLING OVERFLOW  TUBE AND GUIDE TUBE

This kit includes a new overflow tube and guide tube. Before installing the overflow tube on the new transmission oil pan, make sure that the arrows on the bottom of the overflow tube are aligned to each other. The guide tube does not require alignment. Install the overflow tube and guide tube on the new transmission oil pan by snapping them into place, as shown in the photo below.

INSTALLING THREADED FILL PLUG AND CLOSED PLUG

Install the supplied threaded fill plug on the new transmission oil pan and torque to 4 ft-lb (6 Nm). Install transmission pan. Fill the pan through the threaded fill plug. A threaded barb fitting is also provided.
Follow OE instructions to fill pan through fill plug using a transfer pump. You can adjust the position of the overflow tube using the adjustment tool.
After filling, remove the threaded fill plug and replace it with the supplied closed plug. Standpipe design will prevent fluid loss.

REPLACEMENT FILTERS

When replacing filters on the 265-887, use Dorman part number 265-887F. This part contains filters, a gasket, an overflow tube, a guide tube, a threaded fill plug and an adjustment tool. The filters on the OE pan are not replaceable. You can also purchase the adjustment tool separately using part number 265-887T.

Dorman Products, Inc. Corporate Office and Customer Service: 1-800-523-2492.

Disclaimer : Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety features.

BEFORE YOU BEGIN:

• Always wear proper safety equipment when performing repairs.
• Ensure at your point of purchase that this part fits your exact vehicle configuration.
• Reference the appropriate service manual for your vehicle. If you do not have a service manual and do not have the training or experience to perform the necessary procedures correctly, seek the services of a qualified technician.

NEED HELP?

Please call our Technical Support team for assistance from our team of certified automotive experts.

• 1-866-933-2911

© 2022 No reproduction in whole or in part without prior written approval.

FAQS

Where can I get technical support for this product?

Please call our Technical Support team at 1 866 933 2911 for assistance from our certified automotive experts

What is included in the replacement filters part number 265-887F?

The part contains filters, a gasket, an overflow tube, a guide-to-be, a threaded fill plug, and an adjustment tool.

Can I purchase the adjustment tool separately?

Yes, you can purchase the adjustment tool separately using part number 265-887T.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>