DORMAN 99138 Keyless Entry Remote 3 Button Instruction Manual
- June 1, 2024
- DORMAN
Table of Contents
DORMAN 99138 Keyless Entry Remote 3 Button
Product Information
Specifications:
- Model: 99138
- Applications: 4Runner 1999-2002, Sequoia 2003-2007, 4Runner 2003-2009
- Function: Remote key programming
- Compatibility: Driver’s door open, key out of ignition
Product Usage Instructions
For 4Runner 1999-2002 and Sequoia 2003-2007:
- Start with the key out of the ignition, driver’s door open, and all other doors closed and unlocked.
- Perform these steps within 40 seconds:
- Perform 5 lock/unlock cycles using the power lock switch on the driver’s door, starting with lock.
- Close, then open the driver’s door.
- Continue with the following steps within 40 seconds:
- Repeat the lock/unlock cycles on the driver’s door.
- Insert the key in the ignition, turn to ON and then back to OFF based on programming needs.
- Remove the key from the ignition.
- The power door locks should cycle automatically within 3 seconds, indicating successful programming mode entry.
- Follow the steps to program the remote by pressing the lock and unlock buttons simultaneously, then holding the lock button for 2 seconds.
- Repeat step 6 for each new remote and close the driver’s door to complete the process.
For 4Runner 2003-2009:
- Start with the key out of the ignition, driver’s door open, and all other doors closed and unlocked.
- Perform these steps within 5 seconds:
- Insert and remove the key from the ignition twice.
- Continue with the following steps within 40 seconds:
- Close then open the driver’s door.
- Repeat closing and opening the driver’s door.
- Insert and remove the key from the ignition.
- Close the driver’s door.
- Turn the ignition to ON and then back to OFF.
- Remove the key from the ignition.
- The power door locks should cycle automatically within 3 seconds, indicating successful programming mode entry.
Frequently Asked Questions
Q: What should I do if the power door locks do not cycle as expected during programming?
A: Return to step 1 and ensure all conditions are met before proceeding with the programming steps.
Use this procedure for the following applications
4Runner: 1999-2002
Sequoia: 2003-2007
-
Start with key out of ignition, driver’s door is open all others closed and driver’s door is unlocked.
-
Insert key into the ignition (Do NOT Turn) and Pull key out.
-
Perform these steps within 40 seconds.
A. Using the power lock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 Cycle = 1 lock and 1 unlock).
B. Close, then open driver’s door. -
Perform these steps within 40 seconds.
A. Using the power lock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1 Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF once to program remote while retaining the original remote codes. Twice to erase all original codes and add new remote. Three times to check how many remotes are programmed or five times to erase all original codes.
D. Remove the key from the ignition. -
Within 3 seconds the power door locks should cycle automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
-
Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, press the lock button itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once indicating successful programming. If the door locks do not cycle, or cycle twice. Repeat steps A and B in step 6 as your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new remote. -
Close driver’s door.