CAMEC 051411-A Single-Double Electric Step User Guide

CAMEC 051411-A Single-Double Electric Step

Product Information

Specifications

• Maximum weight allowed: 200Kg

Product Usage Instructions

Handling and Transport
The product is shipped individually in a cardboard box. Check for any signs of transport damage and ensure all components are present.

Installation

WARNING: ALL INSTALLATION MUST BE PERFORMED BY QUALIFIED PERSONNEL.

1. Remove the step from the packaging.
2. Lock the step using the appropriate mounting holes.
3. For fixing, use M8 screws of suitable length for the support thickness. Use self-locking nuts only.
4. Refer to the table for clamping forces based on the strength class of the bolt used.
5. Position the step control switch near the door to prevent accidental use.
6. Check for any sharp edges that could pose risks during operation.
7. Ensure correct assembly to avoid incorrect movement.

Electrical Installation

WARNING: STRICTLY FOLLOW THE INSTRUCTIONS SUPPLIED WITH THE STEP.

1. Ensure all wiring connectors are covered with insulating material.
2. Operate the step opening and closing mechanism with caution, following safety regulations.
3. Do not allow children near the step during operation.
4. Steps are equipped with a manual release mechanism for emergency situations. Follow instructions for manual intervention.

FAQ

• Q: What should I do if the step shows signs of transport damage?
  A: Contact the manufacturer immediately and do not proceed with installation.

• Q: Can I install the step myself?
  A: No, all installations must be performed by qualified personnel to ensure proper functioning and safety.

• Q: How do I know if the step is fully opened or closed?
  A: Follow the instructions provided with the step and ensure proper observation before releasing any controls.

CAMEC ELECTRIC STEPS
USER AND MAINTENANCE MANUAL
SINGLE – DOUBLE ELECTRIC STEPS

Introduction

Read carefully before using the step. Keep the instructions in a safe place. Please ensure that

• No improper use of the steps
• Installed by trained personnel
• Not used with primary power failure
• Not used with non original spare parts

WARNING!

• It is up to the user to guarantee that transport , connection, maintenance and repairs are carried out by qualified personnel.
• The manual must be kept for the life of the step and passed on to any subsequent owner.
• Any improper use of the step voids any warranty

Technical information

Maximum weight allowed 200Kg

Handling
The product is shipped individually in a cardboard box, please ensure the steps do not show any signs of transport damage and that all components are present.

Installation

ALL INSTALLATION MUST BE PERFORMED BY QUALIFIED PERSONNEL.

• Remove the step from the packaging. Lock the step using the appropriate mounting holes.
• For fixing it is necessary to use M8 screws of the length suitable for the thickness of the existing support. Use only self locking nuts.
• For clamping forces see the table below based on the strength class of the bolt used. Use a suitable torque wrench for verification.

10.9                                        35 N/m

• Make sure that the fixing points on those structural parts of the vehicle for which the manufacturer guarantees a mechanical resistance to the maximum loads tolerable by the step.
• In the case of the double step this may require cutting of the casing of the vehicle. Position the step control switch near the door where the step is mounted in a way as to prevent accidental use.
• It is the responsibility of the installer to carry out the assembly operation to avoid risky points such as sharp edges.
• At the end of the assembly check to ensure no incorrect movement.
• Warning : the step has moving parts so ensure there are no people near the step, especially children.

ELECTRICAL INSTALLATION

Strictly follow the instructions supplied with the step.

The manufacturer declines all responsibility in the event of malfunction due to incorrect installation on the vehicle.

• Ensure all wiring connectors are covered with insulating material to prevent exposure of contacts to the elements.
• This product must only be used for which it is conceived, that is to go up and down from vehicles in general. The manufacturer cannot be held responsible for any improper use.
• With the vehicle parked the step opening and closing mechanism is controlled by the operator using the switch, once pressed it must be released when fully opened. The user must comply with safety regulations. Ensure the step has come out fully before releasing the button and ensure the same when closing. Make sure no children stand on or near the step during operation.
• The steps are equipped with a mechanical release mechanism to allow the manual movement of the step.
• Always ensure the vehicle is stable and remove the power supply before manual intervention.
• In the upper part of the rear lever there is a small plate which is bolted to the step levers. To unlock the step unscrew with a 13mm wrench and manually close the step. On the opposite side is a hole which will support the step in the closed position using the removed screw.

WIRING FOR SINGLE AND DOUBLE STEP

Motor protection
The motor of each step is protected by a resettable fuse which cuts the current in the event of a prolonged lock.

WARRANTY

Camec guarantees the steps for 24 months starting from the day of purchase

WIRING FOR SLIDING STEPS

Camec Pty Ltd
47-63 Remington Drive Dandenong South VIC 3174
www.camec.com.au Ph: 1300 422 632

References

• Caravan and RV Superstore | Caravan Supplies | Caravan Shop Online – Camec

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>