HAMPTON 2ANTY-B0008 LED Lamp User Manual

June 6, 2024
HAMPTON

2ANTY-B0008 LED Lamp
User Manual

Product name: LED LAMP
Model name: 2ANTY-B0008
FCC ID: 2ANTYB0008
IC: 26025-B0008

Before using a self-ballasted LED lamp please read the safety instructions carefully:

  • Can use on a stable source of voltage that fluctuates in a wide range of AC120V 60Hz;

  • Always turn off the switch when replacing or cleaning the lamp. Remove and install it by grasping only the plastic portion of the lamp.

  • This product can replace incandescent lamps to use in indoor, residential, and commercial lighting;

  • Never use in the following conditions:
    1)Power supply with low voltage DC such as emergency light;
    2)Where water may drop on the lamp;
    3)Unsuitable for application when the lamp must turn on and off frequently;
    4)Do not use in moist spots and airtight lamp fixtures;
    5)This device is not intended for use with emergency exit fixtures or emergency exit lights;

  • This product must not be disposed of together with domestic waste. This product has to be disposed at an authorized place for recycling of electrical and electronic appliances.

  • By collecting and recycling waste, you help save natural resources, and make sure the product is disposed of in an environmentally friendly and healthy way.

  • DISPOSAL: Do not dispose of this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.

  • This is a WIFI signal control dimmable LED Lamp. Please do not use any dimmer.

  • “For lamps with a weight significantly higher than that of the lamps for which they are a replacement, attention should be drawn to the fact that the  increased weight may reduce the mechanical stability of certain luminaires and lamp holders and may impair contact-making and lamp retention.”

  • Use in Dry Locations only

  • The light source contained in this lamp shall only be replaced by the manufacturer or his service agent or a similarly qualified person.

  • For lamps with a weight significantly higher than that of the lamps for which they are a replacement, attention should be drawn to the fact that the increased weight may reduce the mechanical stability of certain luminaires and lamp holders and may impair contact-making and lamp retention.

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television  reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

IC Warning
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement
This product complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HAMPTON User Manuals

Related Manuals