TECH WSZ-22m P Switch User Manual

June 1, 2024
TECH

TECH WSZ-22m P Switch

TECH-WSZ-22m-P-Switch-product

Product Overview

The WSZ-22m switch is a device for controlling the lighting and roller shutters directly from the switch or by means of the Sinum central device. The user can program specific conditions for switching the light on/off and the roller shutters to go up or down. The device consists of two independent switches. Communication with the Sinum central device is done by wire. The WSZ-22m switch has a built-in light sensor which is used to adjust the button backlight brightness to ambient light level.

NOTE!

  • The maximum load of a single output for LED lighting is 200W.

Roller shutter switch

IMPORTANT!

  1. Connecting the roller shutter to the switch outputs in reverse will result in incorrect operation of the device and incorrect calibration.
  2. Before using the switch for the first time, the roller shutter limit switches should be set correctly.
  3. After every ten movements of the roller shutter, automatic calibration takes place – the roller shutter moves to the extreme position and then returns to the set position.
  4. The roller shutter is controlled by constantly applying power supply to a given direction of roller shutter operation.

NOTE:

  • Steps to follow after registering and adding the switch to the Sinum Central device, in the switch settings [Settings > Devices > SBUS Devices > (on the device tile)]:
  1. choose the type of blinds you have: blackout or tilting
  2. when choosing a tilting roller blind, you should also select the tilt angle: 90o lub 180o
  3. perform calibration
    • The tolerance between the height set in the Sinum application and the actual roller blind height level can be max. 5%.
    • When a newer version of the device software is available [Settings > Update center > SBUS Devices], you can update it.

CONTROL OF THE TILTING SHUTTER

While holding the roller shutter up/down button:

  • less than 1.5 seconds – change the angle of the roller shutter elements
  • over 1.5 seconds – change of the roller shutter opening level

How to register the device in the sinum system

The device should be connected to the Sinum central device using the SBUS connector and then enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices > SBUS devices > + > Add device. Then briefly press the registration button 1 on the device. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.
NOTE! Each switch must be registered separately.

How to identify the device in the Sinum system

To identify the device in the Sinum Central, activate the Identification Mode in the Settings > Devices > SBUS Devices > + > Identification Mode tab and hold the registration button on the device for 3-4 seconds. The device used will be highlighted on the screen.

Notes

TECH Controllers is not responsible for any damages resulting from improper use of the system. The manufacturer reserves the right to improve devices, and update software and related documentation. The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website. Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by children. It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resistant

Technical data

  Light switch Roller shutter switch
Power supply 24V DC ±10% 24V DC ±10%
Max. power consumption 1,4W 1W
Maximum output load 4A (AC1)* / 200W (LED) 0,5A
Operation temperature 5°C ÷ 50°C
Communication SBUS (TECH MODBUS)
Dimensions [mm] 164 x 84 x 16
Installation Flush-mountable (electrical box 2 x ø60 mm)

AC1 load category: single-phase, resistive or slightly inductive AC load.

Wiring

TECH-WSZ-22m-P-Switch-fig \(8\)

EU Declaration of Conformity

Tech Sterowniki II Sp. z o.o. ul. Biała Droga 34, Wieprz (34-122)

Hereby, we declare under our sole responsibility that the WSZ-22m switch is compliant with Directive:

  • 2014/35/UE
  • 2014/30/UE
  • 2009/125/WE
  • 2017/2102/UE

For compliance assessment, harmonized standards were used:

  • PN-EN 60669-1:2018-04
  • PN-EN 60669-1:2018-04/AC:2020-04E
  • PN-EN 60669-2-5:2016-12
  • EN IEC 63000:2018 RoHS

The product may not be disposed of to household waste containers. The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled.

Contact

www.sinum.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

TECH User Manuals

Related Manuals