TECH WSZ-22 Wireless Two-Pole White Light and Blinds Switch Instruction Manual
- June 1, 2024
- TECH
Table of Contents
TECH WSZ-22 Wireless Two-Pole White Light and Blinds Switch
Service
tel: +48 33 875 93 80
www.tech-controllers.com
support.sinum@techsterowniki.pl
www.tech-controllers.com/manuals
The WSZ-22 switch is a device for controlling the lighting and roller shutters directly from the switch or by means of the Sinum central device. The user can program specific conditions for switching the light on/off and the roller shutters to go up or down. The device consists of two independent switches and communicates with the Sinum central device wirelessly. The WSZ-22 switch has a built-in light sensor which is used to adjust the button backlight brightness to ambient light level.
NOTE!
The maximum load of a single output for LED lighting is 200W.
Roller shutter switch
IMPORTANT!
- Connecting the roller shutter to the switch outputs in reverse will result in incorrect operation of the device and incorrect calibration.
- Before using the switch for the first time, the roller shutter limit switches should be set correctly.
- After every ten movements of the roller shutter, automatic calibration takes place – the roller shutter moves to the extreme position and then returns to the set position.
- The roller shutter is controlled by constantly applying power supply to a given direction of roller shutter operation.
NOTE
Steps to follow after registering and adding the switch to the Sinum Central
device, in the switch settings
[Settings > Devices > Wireless devices > (on the device tile)]:
- choose the type of blinds you have: blackout or tilting
- when choosing a tilting roller blind, you should also select the tilt angle: 90o lub 180o
- perform calibration
The tolerance between the height set in the Sinum application and the actual roller blind height level can be max. 5%.
CONTROL OF THE TILTING SHUTTER
While holding the roller shutter up/down button:
- less than 1.5 seconds – change the angle of the roller shutter elements
- over 1.5 seconds – change of the roller shutter opening level
How to register the device in the sinum system
Enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices Wireless devices > + . Then briefly press the registration button 1 on the device. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.
NOTE! Each switch must be registered separately.
Notes
TECH Controllers is not responsible for any damages resulting from improper use of the system. The range depends on the conditions in which the device is used and the structure and materials used in the object construction. The manufacturer reserves the right to improve devices, update software and related documentation. The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website. Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by children. It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resistant.
Technical data
| Light switch | Roller shutter switch | |
|---|---|---|
| Power supply | 230V±10%/50Hz | 230V±10%/50Hz |
| Max. power consumption | 1W | 1W |
| Maximum output load | 4A (AC1)* / 200W (LED) | 0,5A |
| Operation temperature | 5°C ÷ 50°C | |
| Communication | Wireless (WTP 868 MHz) | |
| Dimensions [mm] | 164 x 84 x 16 | |
| Installation | Flush-mountable (electrical box 2 x ø60 mm) |
- AC1 load category: single-phase, resistive or slightly inductive AC load.
EU Declaration of conformity
Tech Sterowniki II Sp. z o.o. , ul. Biała Droga 34, Wieprz (34-122) Hereby, we
declare under our sole responsibility that the
WSZ-22 compliant with Directive 2014/53/UE.
Wieprz, 01.12.2023
The full text of the EU declaration of conformity and the user manual are available after scanning the QR
The product may not be disposed of to household waste containers. The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>