SuperEye 6005A Metal Detector User Manual
- October 30, 2023
- SuperEye
Table of Contents
SuperEye 6005A Metal Detector
MD6005 Instruction Manual
The Metal Detector is a versatile and easy-to-use metal detector. It has
higher sensitivity and has the ability to differentiate the ferrous metals and
nonferrous metals. It is suitable for beginners.
Please read the manual carefully before using the unit.
Specification
- Operation Modes: One kind No-motion Mode: As long as there is metal object around the search coil, the detector will have a response.
- Adjusting DISCRIMINATION
- Adjusting TUNE
- Adjusting VOLUME
- Low Batter Indication
- 6.5 inch Water Proof Search Coil
- 1/8 inch Earphone Jack( earphone not supplied)
- Batteries Six AA Batteries(not supplied)
Assembly
Assembly is easy and requires no special tools.
-
Align the plastic trapeziform raised part on the handle, with the trapeziform lower groove at the control box bottom (Figure. I). push the two parts tightly.
-
Align the threaded bolts at the handle bottom, with the knobs under the control box, lock it with the bolts(Figure.2).
-
Turn the stem’s lock nut clockwise until it loosens, lengthen or shorten the stem so when you stand upright with your detector in your hand, the search coil is level with and about l/2 inch above the ground with your arm relaxed at your side. ( Figure.3)
-
Loosen the knobs at the search coil’s end, then adjust the search coil to the desired angle, let the seach coil be parallel with the ground. Be careful not to mistake the location of the search coil(Figure.4).
Batteries
Please use six AA alkaline batteries.
-
Press the “key” on the battery compartment in the direction of the arrow, pull out the battery compartment cover (Figure.5). Note: the UP words is engraved on the battery compartment, don’t mistake the direction.
-
Insert six AA batteries into the compartment as indicated by the polarity symbols marked inside the compartment (Figure.6).
-
Close the battery compartment cover, please note that the UP-side is upon.
-
Six alkaline batteries may be used for more than 40 hours. If you do not plan to use the detector for a long time, remove the batteries.
-
Do not mix old and new batteries.
Panel And Controller
The Panel Controller (Figure. 7)
- Power off: Power on/off power supply. The same knob with the DISC.
- TUNE: It is cooperated with the Red Tuning Button, and adjust balance. Let the detector be in normal operation state.
- Red Button: It is cooperated with TUNE to adjust balance.
- DISC: Adjust DISC will help the operator to differentiate the ferrous metals and nonferrous metals. Note: when it’s in the “MIN” position, the detector sensitivity is the most strong.
- Volume: Is used to adjust the loudness of the speaker.
- Low Batter Indication: When the red LED lights, indicates the user should replace the batte1ies.
- Earphone Jack: When the earphone is plugged in, the speaker will no longer sound.
Quick Start:
To get you master how to operate the metal detector quickly, we suggest that you should read the quick start carefully, and practice indoor. When you are familiar with the detector, you can hunt for the treasures just about anywhere.
-
Prepare with a sort of metal samples
• an iron nail
• a pull-tab and a five cents nickel coin
• a 1 cent zinc coin(after 82 version)
• a 25 cent silver coin -
Lay the metal detector properly
In order to avoid the metals influence the detector, be sure to lay the the metal detector proper! y.
• Lay the search coil properly, keep the angle between search coil and aluminum stem is about 140°. Please note not to mistake it(Figure.8)
• Please take off the watch, ring or other metal objects on your hand or arm. Keep the detector away from the wall, floor and other metal objects.
• Be sure to keep the detector away from the light, TV, computer and mobile telephone, which can cause electro-magnetic interference. -
Turn on
Turn on the power supply. -
Adjust balance.
• Press and hold the “Red Button”, and adjust the ‘TUNE” knob, let the meter pointer points “O” position, reless the Red Button. The meter pointer should maintain near the “O”, now the balance has been adjusted. The detector is in the sensitive detection state.(Fig.10).
• Adjust the Volume potentiometer, let you can hear the light hum tone, don’t adjust it too loud.
• Once you adjust the “DISC” button, you should adjust the balance over again. In general, you should only press the Red Button to let the detector return to the balance state.
• During operating, if there is no metals around detector, while the meter pointer deviates from the “0”position, you should also adjust the balance over again. -
Test samples, discriminate ferrous metal and nonferrous metal.
• Set the “DISC” knob to “MIN”. Adjust the balance to let the meter pointer points “0”. Adjust “VOLUME” to let the detector sound a light hum tone.
• Let the metal samples approach the search coil in turn, pay attention to the meter pointer swing and the voice change.
• When the iron nail approach the search coil slowly, the meter pointer will deflect to the left, and the sound will turn light. When the iron nail is more closer to the search coil, the meter pointer will deflect to the left more and the sound turns more lighter, until it disappears.(Figure.11)
• Let other nonferrous metals approach the search coil, the meter pointer will deflect to the right, and the sound will turn louder. (Figure.12)
-
Discriminate silver
• Set the “DISC” knob to “MAX”. Adjust the balance to let the meter pointer points “0”and the detector sound a light hum tone.
• Let the 25 e silver coin approach the search coil slowly, the meter pointer will deflect to the right, and the sound will turn loud. (Figure.13)
• Let other metal samples approach the search coil slowly, the meter pointer will deflect to the left, and the sound will turn light. (Figure.14)
-
Discriminate different metals approximately
We take 5 e nickel coin and pull tab as an example to explain the approximate discrimination method.
• Set the DISCRIMINATION to about “12:00” position(Figure.15). Adjust the balance to let the detector sound a hum tone, and the show is “0”
• Let the iron nail, 5 e nickel coin and pull tab approach the search coil
slowly, the sound tones light, and the meter pointer deflects to the left.
• Let the higher conductivity objects, such as 1 e zinc coin and 25 e silver
coin approach the search coil slowly, the sound tones louder, and the meter
pointer deflect to the right.
• The “12:00″position is the5 e nickel coin and pull tab discrimination
position.
• Rotate the “DISC” knob from “MIN” to “MAX”, you can find the different
metals discrimination position. The metals with low conductivity,
discrimination position is an ear the left side, and the iron discrimination
position is in the most left(MIN).
The metals with high conductivity, discrimination position is arrear the right
side, and the silver discrimination position is in the most rights (MAX).
-
Explanation
• Discriminating metals is based on the change of sound and meter pointer direction.
The discrimination is preliminary, and it’s only a reference for treasure hunters.
• When the DISC is in the “MIN” position, the detector sensitivity is the most. -
Operation outdoors
By learning, you have learned how to operate the detector. In the wild, as the soil, sea sand, ores and other environmental impacts and the interference of electromagnetic fields, the detector sensitivity and discrimination location will be changed. You should practice time after time and accumulate the experience to master the skill of detect gradually, and you will taste the joy of treasure-hunting.
Field Operation
Metal detector is used outdoors. There is too much metals indoors, and also all kinds of electrical equipments that will bring interference signals, so it’s not fit for using the detector.
Field detection is more complicated, the composition of the b detected regional soil, the component, size, shape and the oxidation degree of the underground metals will all affect the detection results. This chapter is only the general steps of the field detection. The operator should practice time after time and accumulate experience to achieve good results.
-
Tum on
Rotate the DISC knob to the right side, switch on the power supply. Set the VOLUME to the mid, the detector may sound a tone or may be silent. -
Adjust balance
Press and hold the “Red Button”, and adjust the “TUNE” knob, let the meter pointer points to “0”position.Reless the Red Button, the meter pointer should maintain points to “0”position or near the “0” position. Adjust the “VOLUME”, the detector sound a light hum tone, now the balance has been adjusted.
We remind the operator specially, once you adjust the “DISC” button, you should adjust the balance over again. When the detection environment has a change, you should also adjust the balance over again.
In general, after the balance being adjusted, and some balance deviation being occurred, you should only press the Red Button to let the detector return to the balance state. -
Adjust volume
The detector is based on the direction of meter pointer deflection and change of sound to detect metals, and it’s more sensitive to judge by the sound. After the balance being adjusted, adjusting the volume will get a light hum tone, don’t adjust it too loud. -
Adjust DISC
In general, set the “DISC” to “MIN”, the sensitivity is the most at this time. If you find a ferrous metal, the detector tone will tum light, and the meter pointer swing to the left. If you find a nonferrous metal, the detector tone will tum louder, and the meter pointer swing to the right. You should further determine the general type of nonferrous metals by DISC.
Since the soil will deviate the discrimination position, we suggest you take some samples with you, such as iron nail, pull tab, 5 nicker coin, 25 silver coins. Bury these samples in the detection soil respectively, try detecting and observe the different metals discriminations position. It will help you judge the type of the target, in case you omit the treasures that you want to find. -
Move the search coil
When moving the search coil, you should move it at a constant speed, not unsteadily. Let the search coil be parallel with and about 1/2 inch from the surface, not to swing it like a pendulum high and low above the ground.( Figure. I 6, 17)
When finding metal objects, you should move the search coil on the ground according to figure 16, In order to determine the metal position exactly. The nearer the search coil from the object, the more strong the response is.
-
Using the earphone
To the change of sound, using the earphone is more sensitivity, and you will get better detection result.
Caution
- Before detection every time, you should press Red Button to adjust balance, let the detector be in most sensitive state. But when detecting, you should not press the Red Button.
- The volume just be adjusted to let you could hear the sound, not adjust it too louder. At this time, the people is the most sensitive to the sound.
- In areas with heavy traffic, please don’t wear earphone, in case an accident occurs.
- Always obtain permission before searching any site.
- Keep away from the region that may bury electrical line, cable line or pipeline, in particular the pipes that are full of flammable gases and liquids.
- Do no detect in the military area that may bury bombs or gas explosives.
- When digging out the target, use the reasonable method, do not destroy the vegetation. Leave the land and vegetation as it was after excavation.
- When using earphone, don’t set it too louder, in case it’ll destroy your hearing.
Trouble Shooting Guide
SYMPTOM|
SOLUTION
---|---
No power|
- Be sure that the polarity of batteries are installed correctly.
- Replace the batte1ies.
The unit is silent when turns on, and the meter pointer doesn’t move, it seems
there is no electricity.| The balance has a deviation. Press the Red Button,
and adjust the TUNE knob to let the detector be in balance state.
Sound an irregular tone.|
- Make sure there is no other metal detector operating around.
- Don’t use it indoors, because there is many metals there.
- Make sure whether there is electromagnetic interference sours , such as power lines, cables, electronic fences and so on. Keep away from these areas.
- The ground is serious magnetized.
PARTS LIST
Part | Description | Q’ty |
---|---|---|
1 | PCB | 1 |
2 | Screw M3X8 | 2 |
3 | Adhesive Sticker | 1 |
4 | LED | 1 |
5 | View Meter | 1 |
6 | Washer3mm | 2 |
7 | ScrewM3X8 | 2 |
8 | Control Panel | 1 |
9 | Support Arm(Right Side) | 1 |
10 | NutM4 | 4 |
11 | Screw M3X18 | 4 |
12 | Screw M3X14 | 1 |
13 | SENS Dial | 1 |
14 | Knobs | 2 |
15 | TUNE Dial | 1 |
16 | Speaker | 1 |
17 | Suo Oort Ann(Left Side) | 1 |
18 | Screw M3X25 | 2 |
19 | Red Botton /Switch | 1 |
20 | Left Arm Rest Support | 1 |
21 | Screw M3Xl2 | 3 |
22 | Right Arm Rest Support | 1 |
23 | Support Arm Adjustment Knob | 1 |
24 | Outer Stem | 1 |
25 | Washer | 1 |
26 | Inner Stem | 1 |
27 | Lock Nut Interior | 1 |
28 | Lock Nut Exterior | 1 |
29 | Look Nut Cover | 1 |
30 | Bushing | 1 |
31 | Coil Button(Nut) | 1 |
32 | Coil Button(Screw) | 1 |
33 | Search Coil | 1 |
34 | Support Arm Pad | 1 |
35 | Earphone Jack | 1 |
36 | Battery Compartment | 1 |
37 | Battery Compartment Cover | 1 |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>