ENDORFY EY8E002 Atlas L Electric Gaming Desk Instruction Manual
- June 1, 2024
- ENDORFY
Table of Contents
EY8E002 Atlas L Electric Gaming Desk
Specifications
- Height range: 720 – 1200 mm (4 memorized positions)
- Width: 1500 mm
- Weight capacity: 80 kg
Product Usage Instructions
Control Panel
- Move up: Press the corresponding button to raise the desk.
- Move down: Press the corresponding button to lower the desk.
- Height preset 1-4: Save your preferred heights by pressing the Memory button and then 1/2/3/4.
Troubleshooting
- Hot: Allow the electric motor to cool down for 20 minutes before replugging it.
- E10: Check motor and control panel connections when experiencing power issues.
- E20: Remove weight from the desk if an overload alarm occurs.
- E02: Ensure the desk is on an even surface to avoid rebound/vibration issues.
- E32: Check connections and power off in case of an overvoltage alarm.
- E31: Power off and check connections if an undervoltage alarm is triggered.
- E60: Reinstall both legs at the same height if there’s a height difference alarm.
Reset
- To reset the desk, lower it to the lowest position and hold the
- Reset the button for 5 seconds.
PARTS
INSTALLATION
Please tighten the screws
gently to avoid any damage. Screwdriver (not included)
Different positions could be chosen for headset hook
Controller: left and right positions could be chosen on your requirement
Caution : extension cord (P) has to be used if the controller is installed on the left side
Well done, you can now plug-in power adapter
WARNING
CONTROL PANEL
EN **CONTROL PANEL**
Move up
Move down
Height preset 1
Height preset 2
Height preset 3
Height preset 4
Memory button: press it (LED display will start flashing) and then press 1 / 2
/ 3 / 4 to save the preset.
TROUBLESHOOTING
Hot
| Over-heating protection. Plug it off, allow the electric motor to cool down for 20 minutes, then replug it.
E10
| Power it off and check the connection of the motor and control panel.
E20
| Overload alarm. Remove the weight of the desk and replace the power connector.
E02
| Rebound/vibration protection. Check if the desk stands on an even surface or if there are no blocking objects under the desk.
E32
| Overvoltage alarm. Power off first and check whether the connection is proper.
E31
| Undervoltage alarm. Power off first and check whether the connection is proper.
E60
| Alarms when the height difference between left and right legs exceeds the
set value. Power off first and reinstall both legs at the same height.
RESET
Adjust the desk to the lowest position (by pressing ).
In the lowest position click and hold button for 5 seconds.
Safety instruction
- The product should be used as intended. Incorrect use may damage the product and be dangerous to your health.
- Make sure that the product is in good working order before using it.
- The warranty does not cover mechanical damage to the product.
- This device is intended for indoor use, under normal humidity conditions. Do not use it outdoors.
- Do not install and use the device within reach of children.
- To prevent damage from condensation, allow the device to warm up to ambient temperature before use.
- Clean only with a dry, clean cloth. Do not handle it with wet hands.
- No user-serviceable components inside. Return to an authorized service center for repairs.
- Opening the device or modifying it will void the warranty.
- Do not use the product near liquids or in places where it may be directly exposed to liquids. If the device comes into contact with any liquids, immediately disconnect it from the power source.
- In the event of a malfunction, disconnect it from the power source immediately and contact Endorfy Technical Support.
- Do not discard electrical and electronic equipment together with other household waste.
- The end user is responsible for the correct disposal of unnecessary or faulty electrical equipment by returning it to the collection point or the seller. Contact local authorities or the store where you purchased the product for additional information.
- The product should be assembled according to the instructions, using appropriate tools.
- Do not use power tools (e.g. an electric screwdriver) to assemble the product – this may damage the threads.
- After 14 days from the first assembly, re-tighten all bolts.
- Before using the product, make sure that it has been correctly assembled and is placed on an even, stable surface.
- Do not stand on the seats, tabletops, armrests, or headrests, or swing in or lean out of the chairs.
- Do not place the product less than 1 m away from active heat sources.
- Periodically inspect the condition of the product and re-tighten any loose connections.
- Do not exceed the maximum load for the particular product (information in the instructions).
- Failure to observe the rules mentioned above may result in permanent health impairment.
- Sharp, heavy, and rough objects, as well as pet claws, may damage the material / eco-leather / tabletop.
- Before adjusting the height of the tabletop, make sure that there are no people or objects next to or under the desk.
SCAN THE QR CODE
NEED MORE INFORMATION?
ENDORFY.COM/KB/EY8E-ATLAS-L-ELECTRIC
FAQ
- Q: What should I do if the desk feels hot?
- A: Allow the electric motor to cool down for at least 20 minutes before using it again.
- Q: How can I save my preferred desk heights?
- A: Press the Memory button, then press 1/2/3/4 to save your desired heights.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>