snap one LUM-A20-POE60W Gang Plate for Electric Gang Box Instruction Manual
- June 1, 2024
- Snap One
Table of Contents
snap one LUM-A20-POE60W Gang Plate for Electric Gang Box
Specifications
- Model: LUM-A20-POE60W
- Short-Circuit Protection Rating: 20A
- Network Environment: PoE (Environment 0)
Product Usage Instructions
Cleaning
Clean the product only with a dry cloth to prevent any damage.
Power Cord Safety
Protect the power cord from being walked on or pinched, especially at
plugs, convenience receptacles, and where they exitfrom the device.
Power Management
To disconnect the unit power from the AC mains, remove the power cord from
the appliance coupler or turn off the circuit breaker. When reconnecting
power, ensure the circuit breaker is turned on following all safety
guidelines.
Grounding and Bonding
If connecting rooftop devices like a satellite dish, ensure proper
grounding of wires. The bonding point can provide a common ground for other
equipment using specified hardware and wire size.
Interference Prevention
Avoid placing the product near electrical equipment such as tape recorders,
TV sets, radios, computers, and microwave ovens to prevent interference.
Object Insertion
Avoid pushing objects into the product through cabinet slots to prevent
contact with dangerous voltage points or shorting out parts that could lead to
fire or electric shock.
PoE Network Connection
Ensure the product is connected only to PoE networks without routing to the
outside plant as per installation instructions for proper operation.
FAQ
-
Q: What should I do if the product causes interference with my electrical devices?
A: To prevent interference, ensure the product is not placed in close proximity to devices such as tape recorders, TVs, radios, computers, or microwave ovens. -
Q: How should I clean the product?
A: Clean the product using only a dry cloth to avoid any damage.
Regulatory Compliance & Safety Information for Model LUM-A20-POE60W
Important Safety Instructions
Read the safety instructions before using this product
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water.
-
Clean only with dry cloth.
-
Do not block any ventilation openings. Install by the manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Only use attachments/accessories specified by the manufacturer.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
-
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
-
This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. Unplug this apparatus during lightning storms or when unused for long periods of time.
-
To completely disconnect unit power from the AC mains, remove the power cord from the appliance coupler and/or turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. The circuit breaker shall remain readily accessible.
-
This product relies on the installation of the building for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A.
-
WARNING – Power Sources, Grounding, Polarization
This product requires a properly grounded outlet for safety. This plug is designed to be inserted into a NEMA 5-15 (three-prong grounded) outlet only. Do not force the plug into an outlet that is not designed to accept it. Never dismantle the plug or alter the power cord, and do not attempt to defeat the grounding feature by using a 3-to-2 prong adapter.If you have a question about grounding, consult your local power company or qualified electrician.
If a rooftop device such as a satellite dish connect to the product, ensure that the devices’ wires are also properly grounded.
The bonding point can be used to provide a common ground to other equipment. This bonding point can accommodate a minimum 12 AWG wire and should be connected using the required hardware specified by the other bonding point. Please use termination for your equipment in accordance with the applicable local agency requirements. -
Notice – For indoor use only, Internal components are not sealed from the environment. The device can only be used in a fixed location such as a telecommunication center, or a dedicated computer room. When you install the device, ensure that the protective earthing connection of the socket outlet is verified by a skilled person. Suitable for installation in information technology rooms by Article 645 of the National Electrical Code and NFP 75.
-
This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers, and microwave ovens if placed nearby.
-
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in fire or electric shock.
-
WARNING – No user serviceable parts inside. If the product is not operating properly, do not remove any part of the unit (cover, etc.) for repair. Unplug the unit and consult the warranty section of the owner’s manual.
-
PoE considered a Network Environment 0 per IEC TR62101, and thus the interconnected ITE circuits may be considered ES1. The installation instructions clearly state that the ITE is to be connected only to PoE networks without routing to the outside plant.
The lightning flash and arrow head within the triangle is a warning sign
alerting you of dangerous voltage inside the product
Caution : To reduce the risk of electric shock, do not remove cover (or
back). No user serviceable parts inside. Refer servicing to qualified service
personnel.
The exclamation point within the triangle is a warning sign alerting you of
important instructions accompanying the product.
See marking on bottom/back of product
Warning!: To reduce the risk of electrical shock, do not expose this
apparatus to rain or moisture
Save these instructions
Compliance of this equipment is confirmed by the following label that is placed on the equipment:
USA & Canada Compliance
FCC Part 15, Subpart B & IC Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
IMPORTANT! Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment
Canada Warning Statement:
CAN ICES-003 (B)/NMB-003(B)
This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
Europe Compliance
Compliance of this equipment is confirmed by the following logo that is placed
on the product ID label that is placed on the bottom of the equipment. The
full text of the EU Declaration of Conformity (DoC) is available on the
regulatory webpage
United Kingdom (UK) Compliance
Compliance of this equipment is confirmed by the following logo that is placed
on the product ID label that is placed on the bottom of the equipment. The
full text of the UK Declaration of Conformity (DoC) is available on the
regulatory webpage:
Recycling
Snap One understands that a commitment to the environment is essential for a
health life and sustainable growth for future generations. We are committed to
supporting the environmental standards, laws, and directives that have been
put in place by various communities and countries that deal with concerns for
the environment. This commitment is represented by combining technological
innovation with sound environmental business decisions
WEEE Compliance
Snap One is committed to meeting all requirements of the Waste Electrical and
Electronic Equipment (WEEE) directive (2012/19/EC). The WEEE directive
requires the manufacturers of electrical and electronic equipment who sell in
EU countries: (1) label their equipment to notify customers that it needs to
be recycled, and (2) provide a way for their products to be appropriately
disposed of or recycled at the end of their product lifespan. For collection
or recycling of Snap One products, please contact your local Snap One
representative or dealer.
Australia & New Zealand Compliance
Compliance of this equipment is confirmed by the following logo that is placed
on the product ID label that is placed on the bottom of the equipment.
About this Document
Copyright © 2023 Snap One All rights reserved.
1800 Continental Blvd. Suite 200-300 • Charlotte, NC 28273 866-424-4489 • snapone.com