snap one B-260-SWTCH-5X1 18Gbps HDMI 5×1 Switcher Installation Guide
- June 13, 2024
- Snap One
Table of Contents
- snap one B-260-SWTCH-5X1 18Gbps HDMI 5×1 Switcher
- Product Information
- Product Usage Instructions
- Features
- Package Contents
- Warning
- Operation and Functions
- Installation
- IR Control
- Communication Format
- Specifications
- Warranty and Legal Notices
- Technical Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
snap one B-260-SWTCH-5X1 18Gbps HDMI 5×1 Switcher
Product Information
- Product Name: B-260-SWTCH-5X1
- Model: 18Gbps HDMI 5×1 Switcher
- Compatibility: HDMI 2.0/ HDCP 2.2
- Video Resolutions: Up to 4K@60Hz 4:4:4 8bit
Features:
- HDMI 2.0 and HDCP 2.2 compliant
- Supports video resolutions up to 4K2K@50/60Hz 4:4:4
- 18Gbps video bandwidth
- Supports 3D and HDR format video
- Supported HDMI audio formats: LPCM, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-EX,DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD
- Auto/manual switching mode for the input source
- Supports CEC control
- Flexible control via front panel buttons, IR remote, or RS-232 commands
Package Contents:
- B-260-SWTCH-5X1 HDMI Switcher
- IR Remote (with coin/button cell battery)
- HDMI Cable (not included)
- Power Supply (12V DC, 2A)
Product Usage Instructions
- Connect an HDMI cable from the source device to the HDMI inputs of the switch.
- Connect an HDMI cable from the display to the switch’s HDMI out port.
- Connect any IR receivers or control systems to the switch.
- Connect the switch’s power supply to a power outlet.
- The Power, Output, and selected Input LEDs should glow blue, indicating successful connection.
IR Control:
- Power: Press to power the switch on or set it to standby mode.
- Prev: Press to select the previous source.
- Next: Press to select the next source.
- Input 1/2/3/4/5: Press the desired input number to select the connected source.
RS-232 Control:
The switcher can be controlled using RS-232 commands from a PC or control
system. Use the included three-pin phoenix connector to connect the control
device to the switcher.
Communication Format:
- Baud rate: 9600 bps
- Data bits: 8 bit
- Parity: None
- Stop bits: 1 bit
- Flow control: None
Important Safety Warning:
The IR Remote supplied with this product contains a coin/button cell battery.
Keep product and batteries away from children. Battery can cause severe or
fatal injuries in 2 hours or less if swallowed or placed inside any part of
the body. Seek immediate medical attention if it is suspected that a
coin/button battery has been swallowed or placed inside any part of the body.
Welcome to Binary™
This product is engineered to provide years of exceptional reliability. We
appreciate your business, and we stand committed to providing our customers
with the highest degree of quality and service in the industry. This 18Gbps
HDMI 5×1 Switcher is compatible with HDMI 2.0/ HDCP 2.2 and supports video
resolutions up to 4K@60Hz 4:4:4 8bit.
Pro Tip:
Connect the HDMI switch to a surge protector to extend the life of the
product.
Features
- HDMI 2.0 and HDCP 2.2 compliant
- Supports video resolutions up to 4K2K@50/60Hz 4:4:4
- 18Gbps video bandwidth
- Supports 3D and HDR format video
- Supported HDMI audio formats: LPCM, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-EX,DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD
- Has an auto/manual switching mode for the input source
- Supports CEC control
- Flexible control via front panel buttons, IR remote or RS-232 commands
Package Contents
- 1 × 18Gbps HDMI 5×1 Switcher
- 1× IR remote
- 1× 3pin-3.5mm phoenix connector (male)
- 2× Mounting ears
- 4× Machine screws (KM3*4)
- 1× 12V/2A Locking power adapter
- 1× Quick Start Guide QR card
Warning
The IR Remote supplied with this product contains a coin/button cell battery. Keep product and batteries away from children. Battery can cause severe or fatal injuries in 2 hours or less if swallowed or placed inside any part of the body. Seek immediate medical attention if it is suspected that a coin/button battery has been swallowed or placed inside any part of the body.
Operation and Functions
Front Panel
- A. Power LED — Glows blue when the switch is powered on
- B. IR window — Receives IR signals from IR emitting devices
- C. Input LEDs — Glows blue when the input number is selected
- D. Output LED — Glows blue when the HDMI out port is connected to a display
- E. Selection button – Short press to cycle through the inputs. Hold the button for three seconds to enable/disable auto-switching mode for the input source.
Rear Panel
- A. HDMI In ports — Connect an HDMI cable from a source
- B. HDMI Out port — Connect an HDMI cable to a display
- C. IR RCVR PWR switch — OFF to connect to a control system | ON to connect to an IR Receiver
- D. IR EXT port — IR input to connect to IR Receiver or to output of a control system
- E. RS-232 serial port — RS-232 input to connect to the output of a control system
- F. Thread-locking power connector — Connect to the included 12V DC, 2A power supply.
Installation
- Connect an HDMI cable from the source to the HDMI inputs of the switch.
- Connect an HDMI cable from the display to the switch’s HDMI out port.
- Connect any IR receivers or control systems to the switch.
- Connect the switch’s power supply. The Power, Output, and selected Input LEDs should glow blue.
IR Control
- Power — Press to power the switch on or set it to standby mode
- Prev — Press to select the previous source
- Next — Press to select the next source
- Input 1/2/3/4/5 — Press the desired input number to select the connected source
IR Receiver Cable Pinout
IR Receiver Power On
RS-232 Control
The switcher can be controlled using RS-232 commands from a PC or control
system. Use the included three-pin phoenix connector to connect the control
device to the switcher.
Communication Format
- Baud rate: 9600 bps
- Data bits: 8 bit
- Parity: None
- Stop bits: 1 bit
- Flow control: None
| Function | Commmand | Paramter | Description | Return |
|---|---|---|---|---|
| Version | FW VERSION | Get firmware |
version
| V1.01
Power on|
SET POWER
| ON
ON
Power Off| OFF
OFF
Switch input
|
SET SWITCH
|
IN1
|
Switch to input 1
| SWITCH
IN1
IN2
|
Switch to input 2
| SWITCH
IN2
IN3
|
Switch to input 3
| SWITCH
IN3
IN4
| | | | IN4
---|---|---|---|---
IN5
IN5
NEXT
| Switch to the next
input
| SWITCH
IN1
PREV
| Switch to the
previous input
| SWITCH
IN1
Set autoswitch
|
SET AUTOSWITCH
|
ON
| Autoswitch is on| AUTOSWITCH
ON
OFF
| Autoswitch is off| AUTOSWITCH
OFF
Query autoswitch
status
| GET AUTOSWITCH|
| Get autoswitch status|
ON/OFF
- Example: SET SWITCH IN1
switches to input 1. - Note: You must use
or to end a command.
Specifications
Technical
HDMI Compliance| HDMI 2.0
HDCP Compliance| HDCP 2.2
Video Bandwidth| 594MHz/18Gbps
Video Resolution| 480i ~1080p50/60Hz, 4Kx2K@24/30Hz,
4K2K@60Hz
Color Space| RGB, YCbCr 4:4:4 / 4:2:2, YUV 4:2:0
HDMI Audio Formats
| LPCM, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-EX, DTS-96/24, DTS High
Res, DTS-HD Master Audio, DSD
HDR Support| Yes
ESD Protection| Human-body model: ±8kV (air-gap
discharge), ±4kV (contact discharge)
Connection
Input| 5× HDMI IN [Type A, 19-pin female]
Output| 1× HDMI OUT [Type A, 19-pin female]
Control
| 1× RS-232 [3pin-3.5mm phoenix connector]
1× IR EXT [3.5mm stereo mini-jack]
Mechanical
Housing| Metal enclosure
Color| Black
Dimensions (W × D
× H)
| 147mm (5.79″) × 66.3mm (2.61″) × 16mm
(0.63″)
Weight| 246g (0.54 lbs.)
Power Supply
| Input: AC100~240V 50/60Hz
Output: DC 12V/2A (US/EU standard, CE/FCC/UL certified)
---|---
Power Consumption| 3.24W (Max)
Operating
Temperature
| ****
0°C ~ 40°C / 32°F ~ 104°F
Storage
Temperature
| ****
-20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity| 20~90% RH (non-condensing)
Warranty and Legal Notices
Find details of the product’s Limited Warranty and other resources such as regulatory notices and patent and safety information, at snapone.com/legal or request a paper copy from Customer Service at 866.424.4489.
2023, Snap One, LLC. All rights reserved. Snap One and its respective logos are registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4 My Home, SnapAV, Araknis Networks, BakPak, Binary, Dragonfly, Episode, Luma, Mockupancy, Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong VersaBox, SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this specification subject to change without notice.
Technical Support
- For chat and telephone, visit ctrl4.co/techsupport
- Email: TechSupport@SnapOne.com.
- Visit tech.control4.com for discussions, instructional videos, news, and more.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>