Midea HW 7.62 Cooker Hood User Manual

Midea HW 7.62 Cooker Hood

Specifications:

• Model: DE Dunstabzugshaube HW 7.62 / HW 7.92
• Dimensions: 500mm x 286mm x 500mm
• Minimum Installation Height: 650mm
• LED Module Power: 1.5W
• Operating Voltage: DC 12V

Product Usage Instructions

Installation:
To install the hood, follow these steps:

1. Mark points on the wall for mounting brackets as per the provided dimensions.
2. Attach the hood mounting angle and chimney mounting angle using the specified screws.

Connections:
Connect the hood to a flexible or rigid pipe of 150mm or 120mm diameter for ducted installation.

Usage:
Use the control panel on the hood for the following functions:

whenthere is an issue.

Maintenance:
For maintenance, follow these steps:

1. Clean metal grease filters regularly.
2. Replace the activated carbon filter as needed.
3. To replace the LED light module, disconnect power and carefully remove the module.

FAQ:

Q: What is the power consumption of the DE Dunstabzugshaube HW 7.62 / HW 7.92?
A: The power consumption is 16.1 kWh/year.

MODEL: HW 7.62
HW 7.92
www.midea.com

RECOMMENDATIONS AND SUGGESTIONS
The instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. ( When the range hood is located above a gas appliance, this distance shall be at least 65 cm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account. The distance of 65 cm can be reduced for:non-combustible parts of range hoods, and parts operating at safety extra low voltage,Provided these parts do not give access to live parts if deformed 😉 Check that the mains voltage corresponds to that indicated on the rating plate fixed to the hood.
• For Class I appliances,check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm. The route of the flue must be as short as possible.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances),a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air.
• When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Regulations concerning the discharge of air have to be fulfilled.

USE

• The cooker hood is only for home use, not suitable for barbecue, roast shop and other commercial purposes. Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
• Do not flame under the range hood; risk of fire.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• “CAUTION: Accessible parts may become hot when used with cooking appliances”.

MAINTENANCE

• The cooker hood and its filter should be cleaned regularly according to the instruction.
• Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
• Clean and/or repace the Filters after the specified period(Fire hazard).
• Clean the hood using a damp cloth and a neutral liquid detergent.
• The appliance uses 4 hob elements at most.

The symbol is packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

COMPONENTS

DIMENSION

INSTALLATION

WALL DRILLING AND BRACKET FIXING

As a first step, proceed with the following drawings:

• A vertical line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted.
• A horizontal line A at 970 – 1070 mm above the cooker top.
• A horizontal line B at a X mm above the horizontal line A.
• A horizontal line C at a 243 mm below the horizontal line A .

Mark Points:

• Mark a point (1) on the horizontal line A, 80 mm to the vertical reference line.
• Repeat this operation on the other side and on the vertical reference line, checking that the three marks are leveled.
• Mark a point (2) on the horizontal line B, 60 mm to the vertical reference line.
• Repeat this operation on the other side, checking that the two marks are on the same horizontal line.
• Mark a point (3) on the horizontal line C, 100 mm to the vertical reference line . Repeat this operation on the other side , checking that the two marks are leveled.

Fix the brackets :

• Drill holes at the marked points with a ɸ10 mm drill bit.
• Insert the Wall Plugs 11 into the holes.
• Fix the hood fixing bracket 20 with 3 screws 10 (5 x 50) at the horizontal line A.
• Fix a Chimney fixing bracket 21 with 2 screws 10 (5 x 50) at the horizontal line B.

Lower decorative chimney

• Fix the exhaust pipe on the hood body, connect chimney and hood body with 2 screws 12. connect chimney fixing bracket and chimney with 2 screws 12.

Hook the hood body

• Hook the hood body to the bracket 20.
• Level the hood body itself.
• Remove the filter from the inside of the hood body, fix the screws 10 to Wall Plugs 11 at the points (3).

CONNECTIONS

DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ɸ 150 or ɸ 120 mm, the choice of which is left to the installer.

• If to install a ɸ 120 mm air exhaust connection, insert the reducer flange 3 on the hood body outlet.
• Fix the pipe 4 in position using sufficient pipe clamps (not supplied).
• Remove possible charcoal filters.

Upper Decorative Chimney

• Insert the upper decorative chimney 2.2 into the lower decorative chimney 2.1 and drag it up to the horizontal line B
• Connect upper decorative chimney 2.2 and chimney fixing bracket 21 with 2 screws 12 .

USE

MAINTENANCE

GREASE FILTERS
CLEANING METAL SELF-SUPPORTING GREASE FILTERS

• The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
• Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling downwards.
• Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make sure that they are completely dry. (The color of the filter surface may change throughout the time but this has no influence to the filter efficiency).
• When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing outwards.

ACTIVATED CHARCOAL FILTER (RECIRCULATION VERSION)

These filters are not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently with heavy usage.

REPLACING THE ACTIVATED CHARCOAL FILTER

• Remove the metal grease filters.
• Remove the saturated activated charcoal filter. Fit the new filters.
• Replace the metal grease filters.

LIGHTING

LIGHT REPLACEMENT(Completed by professionals)

Replacing the light modules

• Cannot replaced the light bulbs, the entire light module has to be replaced.
• When changing the light modules, the contacts are live.
• Before changing the light module(s), unplug the appliance from the mains or switch off the circuit breaker in the fuse box.

Dismantle LED linght module

• Remove the grease filter and carefully remove the 2 screws from the front plate (a cross headed screwdriver will be needed to remove the screws).
• Disconnect the terminal of LED light.
• Press LED light on the back of the front plate, take the LED light out.
• Replace the lamp(commercially available LED lamp (max.1.5w).

Reinstall LED light module

• Press LED light on the front of front plate, install the LED light on the front plate.
• Connect the terminal of LED light and light leads.
• Carefully fasten the 2 screws on the front plate ,reinstall the grease filter.

DISPOSAL OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

Technical data

Data sheet for household cooker hoods
In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.66/2014

Midea|
---|---
Model name / identifier| HW 7.62 / HW 7.92
Annual Energy Consumption (AEChood)| 16.1 kWh/year
Energy efficiency class| A++
A+ (most efficient) to F (least efficient)| A++
Energy efficiency index (EEIhood)| 31,4
Fluid Dynamic Efficiency (FDEhood)| 37,9
Fluid Dynamic Efficiency class| A
A (most efficient) to G (least efficient)| A
Lighting Efficiency (LEhood)| 76
Lighting Efficiency class| A
A (most efficient) to G (least efficient)| A
Grease Filtering Efficiency| 78.7%
Grease Filtering Efficiency class| C
A (most efficient) to G (least efficient)| C
Airflow at best efficiency point : Exterior / Recirculation| 319,1 m3/h 270,0 m3/h
Air flow (min. speed) : Exterior / Recirculation| 225,7 m3/h       200,7 m3/h
Air flow (max. speed) : Exterior / Recirculation| 480,3 m3/h        420,3 m3/h
Air flow (intensive or boost setting) : Exterior / Recirculation| 647,7 m3/h 570,0 m3/h
Max. air flow (Qmax) : Exterior / Recirculation| 480,3 m3/h        420,3 m3/h
Air pressure at best efficiency point| 264 Pa
Airborne acoustical A-weighted sound power emissions (min. speed)| 45 dB
Airborne acoustical A-weighted sound power emissions (max. speed)| 59 dB
Airborne acoustical A-weighted sound power emissions (intensive or boost setting)| /
Electrical power input at best efficiency point| 61,8 W
Power consumption in off mode (Po)| /
Power consumption in standby mode (Ps)| 0,7 W
Nominal power of lighting system| 3,0 W
Average illumination of the lighting system on the cooking surface| 275 Iux

TROUBLESHOOTING

Light on, but motor does not work

| The blades are blocked.| Check the blades.
The capacitor is damaged.| Replace capacitor.
The motor is damaged.| Replace motor.
The internal wiring of motor is cut off/ disconnected. An unpleasant smell

may be produced.

| Replace motor.

Both light and motor do not work

| Apart from the above mentioned, check the following:
Light damaged.| Replace lights.
Power cord loose.| Connect the wires as the electric diagram.

Oil leakage

| Outlet and the air ventilation entrance are not tightly sealed.| ****

Take down the outlet and seal with glue.

Vibration

| The blade, if damaged, can cause vibrating.| ****

Replace the blade.

The motor is not tightly fastened.| Fasten the motor tightly.
The cooker hood is not tightly fixed.| Fixed the cooker hood tightly.

Insufficient suction

| The distance between the cooker hood and the cooker top is too large.| ****

Readjust the distance.

Too much ventilation from open doors or windows.| Choose a new place to install the appliance or close some doors / windows.

The machine inclines

| The fixing screws are not tight enough.| Tighten the fixing screw and make it horizontal.
The hanging screws are not tight enough| Tighten the hanging screw and make it horizontal.

Warranty policy/ service

We congratulate you to your new device and are convinced that you will be satisfied and have your joy with this modern appliance.

However, if you recognize a reason for a complaint, please contact us:

Midea Europe GmbH Ludwig-Erhard-Str. 14 65760 Eschborn

Phone: +49 6196-90 20 – 0 Fax: +49 6196-90 20 -120
Email: info-meg@midea.com Homepage: www.midea.com/de

In case of service: Phone: +49 6196-90 20 – 0
Fax .: +49 6196-90 20 -120

In case of a technical fault, enter your exact address, telephone number, sales contract number and Device type (from the type plate of the device).
A precise fault description saves you time and money. For special questions, please contact the customer service center.

Before calling for service:
Please check whether there is an operating error or a cause that has nothing to do with the function of your device.
Please observe the note in the user manual and check whether:
Email: service-meg@midea.com

• The power plug is connected
• The power plug may be damaged
• Electricity is available

Warranty terms
This device has been manufactured and tested according to the most modern methods. The seller warrants for faultless material and proper manufacture for a period of 24 months from the date of sale to the end user. The unit is not suitable for commercial use.
The claim under guarantee lapses in the event of intervention by the Buyer or by a third party. Damage caused as a result of improper handling or operation, incorrect installation or storage, improper connection or installation as well as an act […] of God or other external factors shall not be covered by this warranty.

When claims are submitted, the manufacturer reserves the right to make improvements to defective parts or to replace or exchange the device.
Only if it is not possible to achieve the intended use of the device by repairing or replacing the device, the buyer can demand a reduction of the purchase price or the cancellation of the purchase contract within 6 months from the date of purchase.
Claims for damages, including consequential damages, are excluded unless they are based on intent or gross negligence.
The guarantee claim exists only with submission of the product and the purchase receipt. This warranty is valid within Germany.

Importer by:
Midea Europe GmbH
Ludwig-Erhard-Str. 14
65760 Eschborn Germany

References

• Midea - Make yourself at Home - World's Number 1 Appliance Producer
• Midea - Make yourself at Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>