STREET AERO 2016-2023 Chevrolet Camaro SS Quad Exhaust ACM Rear Diffuser Installation Guide

STREET AERO 2016-2023 Chevrolet Camaro SS Quad Exhaust ACM Rear Diffuser

Specifications

• Product Name: 2016-2023 Chevrolet Camaro SS & ZL1 Classic Edition Rear Diffuser
• Manufacturer: Street Aero
• Compatibility: Quad Exhaust models
• Materials: High-quality metal alloys
• Hardware Included: Small Bolts, Small Nuts, M6 16mm Bolts, M6 25mm Bolts, Washers, Finishing Washers

Product Usage Instructions

Step 1: Attaching Fins to the Main Panel

1. Carefully place Fins 1, 2, 3, and 4 onto the Main Panel, matching the numbers.
2. Secure each Fin with Small Bolts and Small Nuts (8 each).

Step 2: Attaching Single L Bracket to Fins

1. Attach and secure the Single L Bracket to Fins 1, 2, 3, & 4 using Small Bolts and Small Nuts (4 each).
2. Ensure the Single L Bracket faces toward the center of the main panel.
3. Do not overtighten; you may need to rotate/adjust the Single LBracket for mounting.

Step 3: Aligning Main Panel and Single L Bracket to Bumper

1. Align the assembled Main Panel to the bumper, centering it as much as possible.
2. Rotate the Single L Bracket to position the Hex Socket side flat against the bumper.
3. Mark and pre-drill holes in the bumper using the Single LBracket as a guide.
4. Secure the Single L Bracket with M6 16mm Bolt, Washer, andNut.

Step 4: Finalizing Installation

1. Pre-drill holes through the Main Panel and bumper.
2. Secure the Main Panel with an M6 25mm Bolt, Finishing Washer, Washer, and Nut.
3. Slide the Side Fin into the Side Panel and secure it with a Small Boltand Small Nut.
4. Align and attach the Side Panel to the bumper using an M6 25mm Bolt, Finishing Washer, Washer, and Nut.
5. Repeat the steps for installing the Passenger Side Panel.

INSTALLATION INSTRUCTION

STEP:1 ASSEMBLE MAIN PENAL
Carefully place Fin 1, 2, 3, and 4 onto the Main Panel (Match the number on the Fin to the number on the Main Panel)
Secure with Small Bolt and Small Nut

STEP:2 INSTALL SINGLE L BRACKET FIN

Attach and secure the Single L Bracket to Fin 1, 2, 3 , & 4 with Small Bolt and Small Nut
NOTE: Single L Bracket must face toward the center of the Main Panel
NOTE : Do Not over tighten the Single L Bracket (You will need to rotate/adjust the Single L Bracket to Mount)

STEP: 3 Mount Main Panel

Align the assembled Main Panel to the bumper
NOTE: Center the Main Panel as much as you can Rotate the Single L Bracket so the Hex Socket side is as flat as possible to the bumper

Mark and pre-drill into the bumper where the hex bolt will be installed
NOTE : Use the hex hole on the Single L Bracket to mark the drill location.
NOTE : Main Panel will need to be removed before pre-drilling

Secure the Single L Bracket with M6 16mm Bolt, Washer, and Nut
NOTE: Reach under the bumper to place the Washer and Nut inside the bumper

STEP: 4 Mount the Rear Diffuser

Pre-drill (4 holes) through the attached Main Panel and into the bumper
Secure the Main Panel to the bumper with M6 25mm Bolt, Finishing Washer, Washer, and Nut
NOTE: Reach under or to the side of the bumper to place the Washer and Nut inside the bumper

Slide the Side Fin into the Side Panel and secure it with a Small Bolt and Small Nut
NOTE : Make sure the Side Fin Bracket faces towards the center of the car

Align the assembled Side Panel to the bumper

Pre-drill (2 holes) through the Side Panel and into the bumper

Secure the Side Panel to the bumper with M6 25mm Bolt, Finishing Washer, Washer, and Nut
NOTE: Reach under or to the side of the bumper to place the Washer and Nut inside the bumper

Repeat to install the Passenger Side Panel to the bumper

• www.streetaero.com
• [email protected]

Frequently Asked Questions

• Q: Can the Rear Diffuser be installed on other car models?
  • A: The Rear Diffuser is specifically designed for 2016-2023 Chevrolet Camaro SS & ZL1 Quad Exhaust models.
• Q: How should I clean the Rear Diffuser?
  • A: Use a mild detergent and water solution with a soft cloth to clean the Rear Diffuser. Avoid harsh chemicals or abrasive materials.
• Q: What should I do if I encounter fitment issues during installation?
  • A: Contact our customer support at [email protected] for assistance with any fitment or installation issues.

References

• Street Aero

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>