STREET AERO 2010-2013 Chevrolet Camaro 2SS Dual Exhaust Installation Guide
- June 1, 2024
- STREET AERO
Table of Contents
STREET AERO 2010-2013 Chevrolet Camaro 2SS Dual Exhaust
Specifications
- Compatible with: 2010-2013 Chevrolet Camaro 2SS (Dual Exhaust)
- Manufacturer: Street Aero
- Model: s-rda-chv-07-e1
- Website: www.streetaero.com
- Contact: info@streetaero.com
Product Usage Instructions:
Step 1: Assembling the Fins and Main Panel
- Carefully place Fin 1 and Fin 2 onto the Main Panel, matching the numbers.
- Secure them with Small Bolt and Small Nut.
Step 2: Removing OEM Part
Remove the OEM Washer Bolt and Clip from the two center bumper fins.
Step 3: Mounting the Main Panel to the Bumper
- Secure Mounting Bracket CT-8 to the OEM mounting hole from Step 2 using M6 55mm Bolt, Finishing Washer, Washer, and Nut.
- Align and secure Mounting Brackets CT-7 and CT-9 to the bumper with provided bolts, washers, and nuts.
- Secure Mounting Brackets CT-7 and CT-9 to the Main Panel.
Step 4: Attaching Side Panel
- Attach Mounting Brackets CT-10 and CT-11 to the Side Panel using M6 16mm Bolt, Finishing Washer, and Nut.
- Attach the Side Panel to the Main Panel with Small Bolt and Small Nut.
- Mark and pre-drill for mounting Brackets CT-10 and CT-11 on the bumper.
- Secure Side Panel by mounting Brackets CT-10 and CT-11 with M6 25mm Allen Bolt, Finishing Washer, Washer, and Nut.
Frequently Asked Questions (FAQ)
-
Q: Can I use power tools to mount the Mounting Brackets?
A: No, it is important NOT to over tighten or use power tools to mount the Mounting Brackets as it may damage the product. -
Q: Do I need to remove any parts before pre-drilling?
A: Yes, in some steps, the Side Panel and Mounting Bracket may need to be removed before pre-drilling into the bumper for installation.
INSTALLATION GUIDE
2010-2013 Chevrolet Camaro 2SS (Dual Exhaust)
Rear Diffuser
STEP: 1 Assemble Main Panel
Carefully place Fin 1 and Fin 2 onto the Main Panel
(Match the number on the Fin to the number on the Main Panel)
STEP: 2 Remove OEM Washer Bolts and Clip
Remove the OEM Washer Bolt and Clip from the two center bumper fin
STEP: 3 Install Mounting Bracket
Mount the assembled Main Panel to the bumper by securing Mounting Bracket CT-8
to the OEM mounting hole on STEP: 2 with M6 55mm Bolt, Finishing Washer,
Washer, and Nut
NOTE: Reach under to place Washer and Nut inside the bumper
Align Mounting Bracket CT-7 and CT-9 to its correct location then Mark
and Pre-Drill into the bumper
NOTE: Use the hole on top of CT-7 and CT-9 to mark the drill location
NOTE: Main Panel and Mounting Bracket may need to be removed before pre-
drilling
Secure Mounting Bracket CT-7 and CT-9 to the bumper with provided M6 25mm
Bolt, Washer, and Nut
NOTE: Reach under the bumper to place the Washer and Nut inside the
bumper
Secure Mounting Bracket CT-7 and CT-9 to the Main Panel with provided M6 16mm
Bolt, Finishing Washer, and Nut
STEP: 4 Mount the Rear Diffuser
Attach and secure Mounting Bracket CT-10 and CT-11 to the Side Panel with M6
16mm Bolt, Finishing Washer, and Nut
NOTE: Push the bolt all the way into the socket to prevent it from
falling out
Attach the Side Panel to the Main Panel with Small Bolt and Small Nut
NOTE: Do Not tighten Small Bolt (you will need to remove the Side Panel
to pre-drill)
Mark where Mounting Bracket CT-10 and CT-11 will be mounted to the bumper
NOTE: Use the hole on top of CT-10 and CT-11 to mark the drill location
Pre-drill into the bumper
NOTE: Side Panel and Mounting Bracket may need to be removed before pre-
drilling
Mount the Side Panel by securing Mounting Bracket CT-10 and CT-11 with M6 25mm
Allen Bolt, Finishing Washer, Washer, and Nut
NOTE: Reach under or to the side of the bumper to place the Washer and
Nut inside the bumper
Repeat to install Passenger Side Panel to the Main Panel and bumper
IMPORTANT: DO NOT over tighten or use power tools to mount the Mounting Brackets
www.streetaero.com
info@streetaero.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>