VOLLRATH T3873260W Cafeteria Breath Guard Instruction Manual

: June 1, 2024
: VOLLRATH

Table of Contents

VOLLRATH T3873260W Cafeteria Breath Guard
Product Information
Product Usage Instructions
FAQ
Installation Instruction
- One Piece Breath Guard Installation
- Three Piece Breath Guard installatiOn
Contact Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLLRATH T3873260W Cafeteria Breath Guard

VVOLLRATH-T3873260W-Cafeteria-Breath-Guard-product

Product Information

Specifications

Product Name: Cafeteria Breath Guard
Variants: One Piece and Three Piece
Manufacturer: Vollrath Company, L.L.C.
Item No.: 2350030-01 Rev 04/12

Product Usage Instructions

One Piece Breath Guard Installation
Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.

Three-Piece Breath Guard Installation

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.

FAQ

Q: What should I do if I encounter cracking while tightening the cap nuts?

A: If you encounter cracking while tightening the cap nuts, immediately stop tightening to prevent further damage. Contact customer service for assistance on how to proceed.

Q: Can the breath guard be adjusted after installation?

A: Yes, depending on the design, some adjustments can be made post- installation. Refer to the user manual or contact customer service for guidance on adjusting the breath guard.

Q: Is it necessary to tighten the cap nuts with a specific torque?

A: It is recommended to tighten the cap nuts securely but avoid over- tightening, as it may cause damage. Use caution and follow the provided instructions for proper installation.

These instructions cover the installation of the one-piece Cafeteria Breath Guard and the three-piece Cafeteria Breath Guard.

Installation Instruction

One Piece Breath Guard Installation

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights. $VOLLRATH-T3873260W-Cafeteria-Breath-Guard-Logo $1$$
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.

Three Piece Breath Guard installatiOn

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights. $VOLLRATH-T3873260W-Cafeteria-Breath-Guard-Logo $2$$
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.