RURIS Navigator 99 Tiller Accessory User Manual

: October 30, 2023
: RURIS

Table of Contents

RURIS Navigator 99 Tiller Accessory
Product Information
INTRODUCTION
OVERVIEW OF THE ACCESSORY
General assembly
TECHNICAL DATA
ASSEMBLY GUIDE
MAINTENANCE
DECLARATION OF CONFORMITY CE
Documents / Resources

RURIS Navigator 99 Tiller Accessory

RURIS-Navigator-99-Tiller-Accessory-PRODUCT

Product Information

The Ruris Tiller Accessory Navigator 99 is a device used for transport and agricultural work. It has one axis and can support a weight of up to 100 kg. The actuation type is a mechanical lifter with manual orders. It comes with recommended rubber wheels of 6.50-8 for transport and 4.00-8 for agricultural work. The braking system is hydraulic with a metal disc caliper.

Product Usage Instructions

Connect the Navigator 99 through the towing eye with a cylindrical bolt.
Regulate the horns of the car at a suitable distance and position.
Use an appropriate speed for transport.
When approaching curves, inclined areas, or turns, reduce the speed to ensure stability.
Use the service brake by acting on the brake lever concomitant with the decoupling clutch motor excavator/Ruris motor excavator.
When finished, park using the parking brake which is acted upon through the ratchet on the brake lever.
For agricultural work, connect the work tools to the special support located in the back.

INTRODUCTION

Dear Client!
Thank you for your decision to purchase a RURIS product and for your trust in our company! RURIS has been on the market since 1993 and during all this time it has become a strong brand, which has built its reputation by keeping promises, but also by continuous investments aimed at helping customers with reliable, efficient, and quality solutions. We are confident that you will appreciate our product and enjoy its performance for a long time. RURIS does not offer its customers only machines, but complete solutions. An important element in the relationship with the customer is advice both before and after the sale, as RURIS customers have at their disposal a whole network of partner stores and service points. To enjoy the purchased product, please read the user manual carefully. By following the instructions, you will be guaranteed a long use. The RURIS company is continuously working on the development of its products and therefore reserves the right to modify, among other things, their form, appearance, and performance, without having the obligation to communicate this in advance. Thank you once again for choosing RURIS products! Customer information and support: Telephone: 0351.820.105 e-mail: info@ruris.ro

OVERVIEW OF THE ACCESSORY

The Navigator 99 lift-towed attachment and accessories must only be used by responsible persons trained in the use of the machine and capable of using it. The Navigator 99 accessory is not approved and equipped for use on public roads or for use on slopes/ramps with an inclination greater than 10º. The lift-towed attachment is a useful attachment for all types of backhoes and backhoes. The Navigator 99 is ideal for traveling on agricultural roads. It is equipped (optionally) with several types of rubber wheels with working and parking brakes. The whole range of accessories for motor homes and backhoes can be attached to this product: plow, rotary plow, fixed harrow, adjustable harrow, harrow, cultivator, potato remover, and rake, with the help of which multiple agricultural works can be carried out. The accessories are mounted in the back, in a special holder, which has an adjustable riser in six indexing positions. Used for both transport and agricultural work, the Navigator 99 is a simple, comfortable, and easy-to-use product.

General assembly

RURIS-Navigator-99-Tiller-Accessory-FIG-1

Support pipe 8. Lifter
Towing eyes 9. Indexor
Connecting pipe 10. Rubber wheels
Curved frame 11. Brake/ indexing levers
Indexing arm 12. Accessory holder
Seat 13. Cables and hoses
Side supports

TECHNICAL DATA

Use: in transport and agricultural work
No. of axes: 1
Supported weight: 100 kg
Actuation Type: lifter: with mechanical indexing
Type of orders: manuals
Rubber wheels (recommended): 6.50-8 for transport;
4.00-8 for agricultural works
Brake: working and parking
Braking system: hydraulic, with metal disc caliper

Navigator 99 is sold without accessories (without work tools), these can be optionally purchased separately.

ASSEMBLY GUIDE

Navigator 99 comes partially assembled, packed, and protected in cardboard boxes. To use it, it is necessary to carry out the simple assembly operations below, exactly in the order described. If you cannot perform these operations, please contact an authorized RURIS service.

Step 1
Assemble the towing eye with the support pipe using the M8 bolt, washer, and nut to which you attach the plastic plug. For good operation, now and periodically, lubricate the shaft, bushing and pipe with RURIS Super Vaseline thick grease.

RURIS-Navigator-99-Tiller-Accessory-FIG-2

Step 2
Insert the connecting pipe into the curved frame pipe. Fix the connecting pipe to the curved frame using M10 screws (2 pcs.), washers, and nuts for it.

RURIS-Navigator-99-Tiller-Accessory-FIG-3

Step 3
Mount the two rubber wheels on their hubs using M10 screws and nuts, 4+4 pcs. The brake disc will be mounted on the left wheel hub. Insert the large spacer bushing on the left axle then insert the wheel. Fit the brake caliper to the disc, then tighten the wheel using the M16 washer and nut. Repeat the process on the right side using the smaller spacer bushing. The hub without the brake disc and caliper will be mounted on the right. Finally, after tightening the M16 nuts, mount the protective covers. For good operation, now and periodically check the normal operation of the bearings. The rubber wheels tighten firmly without large plays, checking their smooth rotation. Finally, all installed bolts and nuts are tightened and checked. The correct and complete assembly is inspected.

RURIS-Navigator-99-Tiller-Accessory-FIG-4

Step 4
Assemble the support pipe and connecting pipe using an M10 screw, washer, and nut, then install a plastic plug.

M RURIS-Navigator-99-Tiller-Accessory-FIG-5

Step 5
Assemble the indexing arm to lifter 1 using the M10 screws, washers, and self- locking nuts, then fix it to the right hub axis using the supplied M8 screw and washers. Insert lifter 2 into the U-bracket of lifter 1, then fix it to the left hub axis using the M8 screw. Fix the two parts of the riser with the M12 screws and washers provided.

RURIS-Navigator-99-Tiller-Accessory-FIG-6

Step 6
Install the seat and leaf spring using your own set of bolts. Mount the assembled seat onto the curved frame mounting bracket as shown. Fix the above assembly together using U clamps, washer, M10 nuts, 4+4 pcs.

RURIS-Navigator-99-Tiller-Accessory-FIG-7

Step 7
Mount the indexing lever and brake lever to the indexing arm using their own screws M6, 2+2 pcs. For the correct installation and use of rubber wheels, also study the next chapter, which includes the adjustment of the Navigator 99, for agricultural work. Inspect the correct fit of the indexing lever and check its effectiveness by indexing the lifter in all positions. Adjust the indexer stroke from the M8 screw and nut on the cable. It is recommended to periodically lubricate the shaft and the rotating bushing of the lifter with RURIS Super Vaseline-type grease.

RURIS-Navigator-99-Tiller-Accessory-FIG-9 Periodic greasing of the indexing bolt and spring (found behind the plastic cover) is also recommended. Inspect the correct mounting of the service and parking brake levers. Periodically, the brake pads are checked and replaced if they are worn and no longer provide adequate braking. Once a year, change the brake fluid in the reservoir at the end of the lever. The type of brake fluid is written on the tank cap – DOT3 or DOT4.

RURIS-Navigator-99-Tiller-Accessory-FIG-7

For correct use and a long duration of use, you must

check at each use that the screws and nuts are sufficiently tightened.
to use a travel speed corresponding to the chosen purpose.
drive at low speed in curves, turns, slopes, and ramps.
before using the work brake lever (before braking) always disengage the clutch lever of the backhoe/backhoe.
make correct adjustments before starting agricultural work.
use suitable RURIS sleeves and RURIS rubber/metal wheels (recommended to have an outer diameter of around 400 mm).
The images are informative, the supplier reserves the right to make structural and functional changes to the machine presented in this manual.

SCHEMES OF OPERATION AND WORKING WIDTH
For good operation and proper execution of agricultural works, observe the following recommendations and work schemes:
Scheme 1 – Balloon type rubber wheel, size 6.50-8

Navigator 99 will be used especially for transport operations.
for transport on agricultural roads, RURIS hoses with a maximum length of 20-25cm will be used.
for plowing works, with DAC or RURIS-type belt excavators, hoses with a maximum length of 20cm will be used.
for plowing works, the motor excavator with a gearbox with gears type RURIS 731, and RURIS 751 sleeves with a maximum length of 15cm will be used.

Scheme 2 and 3 – Rubber wheel narrow, size 4.00-8

Navigator 99 will be used especially for transport operations.
for transport on agricultural roads, RURIS hoses with a maximum length of 20-25cm will be used.
for plowing works, with DAC or RURIS-type belt excavators, RUIRS sleeves with a maximum length of 20cm will be used.
for plowing work, RURIS sleeves with a maximum length of 15cm will be used for the RURIS 731, and RURIS 751 gearbox motor excavators.
When carrying out agricultural work, it is recommended to properly balance the weight of the entire machine by using RURIS 10/20kg counterweights, attached to the metal wheels of the motor home/backhoe.

In transport

The RUIRS backhoe/backhoe is equipped with rubber wheels using, for good stability, RURIS sleeves (coupling parts) as long as possible.
Navigator 99 connects through the towing eye with a bolt cylindrical.
It is regulated horns the car at a distance and positions suitable.
It is carried out transport using a speed appropriately.
Curves and areas inclined ( ramp or slope ), ca and the turns, they will attack with a speed minimum which to ensure the stability of the leader.
The service brake is used always acting brake lever _ concomitant with the decoupling clutch motor excavator / RURIS motor excavator.
In the end, it is parked using the parking brake; this is acted upon through the ratchet on the brake lever.
During agricultural work:
- The accessories ( work tools ) are connected in the support special, located in the back. ( see photo below ) .
- The wheels metallic are all transported in the back, in supports spacious lateral, specially built.
- Navigator 99 connects to excavators through the towing eye with bolt cylindrical.
It carried out transport Navigator 99 equipped with rubber wheels _ in the land, there where they will perform agricultural works
Backhoe/backhoe equip themselves now for Agricultural works with wheel metal use sleeves ( coupling parts ).
It is a regulated indexing arm _ in the position right use the indexing lever.
▪ It is regulated depth and working width appropriate.
▪ It is carried out respective works using a speed proper working executed.
▪ The work accessories rise from the furrow at the end of each row with the help indexing arm; agricultural works are executed no more in the line straight; is strictly prohibited the return car with work tools in the furrow _

MAINTENANCE

Daily, at the end of the work, Navigator 99 will be cleaned of plant remains and other impurities and the technical condition will also be checked:
visible sub-assemblies and external parts and their joints are checked;
all loose joints, screws, and nuts will be tightened, and worn or damaged parts will be replaced with new ones;
the condition of the lifter and the indexing assembly is checked in particular;
checks and adjustments are made to the braking system;
lubrication is carried out in all rotation and indexing points using the RURIS Super Vaseline grease;
if it has faults, Navigator 99 will not be used until they have been fixed. If you cannot carry out these checks and adjustments yourself, please contact an authorized RURIS service.

DECLARATION OF CONFORMITY CE

Manufacturer: SC RURIS IMPEX SRL
Blvd. Decebal, no. 111, Administrative Building, Craiova, Dolj, Romania
Goal. 0351 464 632, www.ruris.ro, info@ruris.ro
Authorized representative: Eng. Stroe Marius Catalin – General Manager
Authorized person for the technical file: Eng. Florea Nicolae – Production Design Director
Product Description: TILLER ACCESSORY NAVIGATOR 99 RURIS is an accessory for RURIS backhoes/backhoes intended for the local transport of the operator (user) from one place to another, depending on the needs related to the agricultural works or the services performed. This accessory is equipped with an indexable rear lifter that can perform a diverse range of agricultural work.
It is equipped with a working and parking brake. This accessory is not intended for transporting people on public roads.
Product: TILLER ACCESSORY
Product serial number: from xx N99 0001 to xx N99 9999, (where xx represents the last two digits of the year of manufacture)
Type: NAVIGATOR 99 RURIS Max. speed allowed: 6 km/hour
Maximum load: 100 kg Working load: max 80 kg

We, SC RURIS IMPEX SRL Craiova, producer, in accordance with HG 1029/2008 – regarding the conditions for the introduction of machines on the market, Directive 2006/42/EC – safety and security requirements, the Standard, EN ISO 12100:2010 – Machines. Security, I have completed the attestation compliance of the product with the specified standards and we declare that it complies with the main safety and security requirements does not endanger the life, health, work security, etc user, and has no negative impact on the environment.

The accessory-type product described above has the technical data from the established instructions for use, the technical data sheet of the product, and/or the working machine. Undersigned Stroe Catalin, the representative of the manufacturer, I declare on my own liability as the product is in accordance with the following standard and European directives:

SR EN ISO 12100:2011/ EN ISO 12100:2011 – Security cars General design principles. Risk assessment and reduction risk
SR EN 1853+AC:2019/ EN 1853:2018+AC:2019 – Machines agricultural Trailers Security
SR EN ISO 13850:2016/ EN ISO 13850:2015 – Security cars. Emergency stop;
SR EN 349+A1:2008 – Security cars distance minimum for prevention crushing Parthians Corps human
SR EN ISO 13857:2020/ EN ISO 13857: 2020 – Safety distance for protecting

LIMBS higher and lower
SR EN 709+A2:2010 – Machines Agriculture and forestry. Pedestrian equipped with cutters worn, sweepers and wheel cutters _ motor ;
Directive 2006/42/EC – regarding cars – the introduction of cars to the market

Other Standards or specifications used: