ErgoAV ERDS1-01G ErgoFx Adjustable Height Standing Desk Instruction Manual

ErgoAV ERDS1-01G ErgoFx Adjustable Height Standing Desk

Product Information

• Product Name: Electric Standing Desk
• Model: ERDS1-01G
• Manufacturer: ErgoAV
• Contact Information:
  • Customer Care Phone: 877-419-7832
  • Email: support@ergoav.com
  • Website: www.ergoav.com
  • Address: 9501 Louisiana Ave N, #200, Brooklyn Park, MN 55445

Package Contents

• Desktop (Box 1 of 2)
• Standing Desktop (Box 2 of 2)
• Adjustable Height Legs
• Bolts M6 x 16 A x8
• Allen Wrench B x1

Weight Restrictions

• Maximum Weight: 176.4 lbs / 80 kg
• Do not exceed the maximum weight indicated. Using the desk with products heavier than the maximum weight may cause damage and/or injury.

Product Usage Instructions

• Step 1: Prepare the Desktop Assembly

  • Place the Desktop [01] assembly on a clean and flat ground.
  • Arrange the desktop according to the diagram.
  • Remove the covers on the left and right sides of the desktop.

• Step 2: Install the Legs

  • The Legs [02] & [03] are pre-tilted according to the view.
  • Snap the grooves on both sides of the rear end of the legs into the protruding parts on both sides of the side plate.
  • Rotate and press the legs downward to secure them.
  • Before installing the left leg, press down the power cable first.
  • Ensure the legs are securely installed and connect the power cable as shown.

• Step 3: Connect Power Cords
  The power cords from the left and right legs should be connected to the power cords on both sides of the desktop. Then connect the plug of the spring cable to the desktop.

• Step 4: Install Cover Sleeves
  After installing the legs, insert the left and right cover sleeves, which will be attracted to the magnetic surface at the bottom.

• Step 5: Install Feet

1. 1. Tighten the Bolts [A] with an Allen Wrench [B] to install the  

   Feet [04] onto the Legs [02] & [03].

• Step 6: Flip Over the Table
  After the installation of the table is completed, it needs to be flipped over. It is necessary to flip it from the other side of the controller to avoid damaging the controller under pressure. You may need assistance with this step.

Additional Instructions

If you need to install a monitor stand on top of the desk, please refer to the provided Desktop Protector Pad installation instructions to prevent potential damage during the installation process.

INTRODUCTION

THANK YOU FOR CHOOSING THIS ERGOAV PRODUCT!
At ErgoAV, we want to add value to your AV experience by providing the highest quality products and services in the industry. If you have any concerns or comments, please contact us.

NOTE
We have packaged this standing desk into two separate parcels. Please make sure to receive both parcels before assembling the desk.

Important Safety Information

• Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our Technical Support line at 877-419-7832 or Customer Service at support@ergoav.com.
  CAUTION: Use with products heavier than the maximum weights indicated may result in instability causing possible injury.

• Please check whether the packaging contents are intact or damaged before assembly.

• Check whether the appearance and wires of the product are damaged. If there is any damage, please do not assemble or operate the product.

• Ensure that the product is not connected to a power source during the assembly process.

• Ensure that there are no unnecessary obstacles near the assembly area.

• Do not soak any parts in liquid, only use a dry cloth or a slightly wet cloth to clean product parts.

• Do not place any wires on a heat source.

• Be careful to avoid electric shock when plugging in the power.

• Please do not operate the desk continuously for more than two minutes to prevent damage to the motor.

Weight Restrictions

WARNING
DO NOT exceed the maximum weight indicated. This desk is intended for use only within the maximum weight indicated. Use with products heavier than the maximum weight indicated may result in failure of the desk and its accessories, causing damage and or injury.

Supplied Parts and Hardware

Warning: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, please contact our Technical Support line at 877-419-7832 or Customer Service at support@ergoav.com

• Please note: Not all hardware included in this package will be used.

ASSEMBLING INSTRUCTION

• Step 1 Place the Desktop [01] assembly on a clean and flat ground, arrange it according to the diagram, and remove the covers on the left and right sides.

• Step 2 The Legs [02]&[03] are pre-tilted according to the view, and the grooves on both sides of the rear end are used to snap into the protruding parts on both sides of the side plate. Rotate and press the legs downward. After the legs are installed, connect the power cable as shown.

• Step 3 The power cords from the left and right legs should be connected to the power cords on both sides of the desktop. Then connect the plug of the spring cable to the desktop.

• Step 4 After installing the Legs, insert the left and right cover sleeves, which will be attracted to the magnetic surface at the bottom.

• Step 5 Tighten the Bolts [A] with a Allen Wrench [B] to install the Feet [04] onto the Legs [02]&[03].

• Step 6 After the installation of the table is completed, it needs to be flipped over. It is necessary to flip it from the other side of the controller to avoid damaging the controller under pressure.

CAUTION!
For the Galaxy Glass Standing Desk, we have also provided a Desktop Protector Pad. When you need to install a monitor stand on top of the desk, please refer to the illustration below to install the Desktop Protector Pad to prevent potential damaging that may occur during the installation process of a monitor stand.

For C-Clamp Mounting

For Grommet Mounting

Using the Wireless Charging and USB Charger

After placing the mobile phone on the wireless charging module, the module rises 60° and rotates 30° clockwise horizontally, and the mobile phone automatically detects charging. When the mobile phone is removed, the wireless charging module returns to its original position.

Using the Control Panel

NOTE: If you don’t understand the introduction of the standing desk controller’s functions, you can scan the QR code to download the APP. The APP can also control the standing desk, giving you a smarter experience. Before using this app on Samsung phones, you need to turn off the built-in Bixby

• Low-Power Function
  If there is no operation for 10 seconds, it will enter low-power mode, and the hand controller will display before turning off the screen and going to sleep.

• Memory Key Function

  • There are two presets for the memory function. One for heights greater than 35.5” and one for lower than 35.5”. After setting the memory function, double push/pull on the control panel will adjust the table to either memory height 1 or 2.
  • Method of setting: Press the M button located on the right-hand side of the control panel, and will appear. When the desk is above 35.5 inches, press and hold for M button 1 second, will appear on the screen and the current position will be saved. When the desk is below or equal to 35.5 inches, press and hold for 1 second, will appear on the screen and the current position will be saved.

• Sedentary Reminder Function

  • After setting the sedentary reminder time, press the button on the left side of the control panel to turn on or off the sedentary reminder function. The sedentary reminder function will not be timed when the desk height is above 39.3 inches. The sedentary reminder function will be timed when the desk height is 39.3 inches or below. After the sedentary time ends, the interface alternately displays and at 1.5-second intervals. Prompting you to raise the desk to your desired height. The sedentary reminder function can also be set on the APP.
  • Method of setting: Press and hold the M key for 5 seconds. After appears, enter the main menu. Toggle the control panel up or down to locate sedentary reminder function. After locating the sedentary reminder interface with , press the M key to enter the corresponding submenu. Toggle the control panel up or down to set the sedentary reminder time. Once confirming the sedentary reminder time, a confirmation icon will be displayed.

• Upper and Lower Limit Function

  • After setting the upper and lower limit function, when you pull the control panel up to reach the set upper limit, the desk will stop rising. When you push the control panel down to reach the set lower limit, the desk will stop descending once limit is reached.
  • Method of setting: Press and hold the M key for 5 seconds. Enter the main menu. Toggle the control panel to reach Upper and Lower Limit Function interface with , press the M key to enter the corresponding submenu. Use the control panel to toggle up or down to the page. Once on page, select the current position as the upper or lower height limit. After setting a height limit, if you want to adjust the desk to the other preferred limit, re-enter the menu and repeat the process.

• Control Panel Lock Function

  • The control panel lock function is designed to prevent accidental adjustments of the desk height through the control panel. Once the function is activated, the height of the standing desk cannot be adjusted through the control panel, but only through the APP. The control panel can be used again for adjustments after unlocking by following the steps below.
  • Method of setting:
  • Press and hold the M button for 5 seconds to enter the main menu interface. Toggle the control panel up and down to display the control panel lock interface and press the M button to enter the corresponding submenu. Choose to turn on the control panel lock or turn it off .
  • When the control panel lock function is set successfully, the control panel will enter the lock mode after 10 seconds of inactivity. After pressing any button, the illustration appears. Follow the button unlocking sequence in the illustration to return to the height display screen.

• Reset Function

  • After resetting the control pad any error message on the display screen will be cleared. Once reset, the desk will be at the highest position due to reset instructions and will not return to its original height unless manually done. All previous settings (memory positions, upper and lower limit, etc.) will not be reset.
  • Method of setting: When an error occurs, please refer to the attachment of the manual for troubleshooting (Error Code Solutions). Then press the control pad downwards for 5 seconds, until the screen displays . Once is shown, the desk is in a reset state. Once in the reset state, release the control panel. After releasing it, press the control panel downwards again to start the reset. During the reset, the desk will rise to its highest position. After reaching the highest point, the reset is complete, and the screen will display the value of the desk’s highest/current position.

Protection Mode Error Codes

any object blocking the rise and lowering motion of the desk.

If the issues from above mentioned are worked out, long-press the down button to reset, and after the reset is completed, continue using it.

E02| M2 Over Current Protection
E03| M3 Over Current Protection
E04| M4 Over Current Protection
E05| M5 Over Current Protection
E06| M6 Over Current Protection
E07| M1 Hall Fault| Check if the legs are tightened, after eliminating the anomaly, long-press the down button to reset, and after the reset is completed, continue using it.
E08| M2 Hall Fault
E09| M3 Hall Fault
E10| M4 Hall Fault
E11| M5 Hall Fault
E12| M6 Hall Fault
E13| Communication interruption between controller A and B.| Check if the connector between the A and B controllers is disconnected. After eliminating the anomaly, long-press the down button to reset, and after the reset is completed, continue using it.
The height difference between the two legs of the controller exceeds the set value and is not synchronized.| Check if the legs are tightened, after eliminating the anomaly, long-press the down button to reset, and after the reset is completed, continue using it.
H01| Overheat Protection (Work Mode Protection)| The controller needs to rest for a while. After the temperature drops, it can continue to be used.

FOR MORE INFO

• At ErgoAV, we strive to provide the highest value products.
• We want to support your purchase.
• If you have questions, concerns, or feedback please let us know!

ABOUT COMPANY

• ErgoAV Customer Care
• phone 877-419-7832
• email: support@ergoav.com
• website: www.ergoav.com
• address: 9501 Louisiana Ave N, #200, Brooklyn Park, MN 55445

References

• ErgoAV

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>