ERGOAV ERDGM2-01B Gas Spring Mount Instruction Manual

ERGOAV ERDGM2-01B Gas Spring Mount

Product Information

Model: ERDGM2-01 B
ErgoAV provides high-quality AV products and services. If you have any concerns or comments, please contact ErgoAV Customer Care at (877)419-7832 or support@ergoav.com. The product manual is available in English, French, and Spanish.

Important Safety Information

Do not exceed the maximum weight limit of 4.4-26 lbs. (2.0-11 kg). The mount is compatible with monitors that have a VESA pattern between 75 x 75mm/3 x 3 (WxH) and 100 x 100mm/4 x 4 (WxH).

Product Features

• C-Clamp Mounting for table edge 3/4 ~ 3 5/32 (20~80mm)
• Grommet Mounting for grommet bolt 3/4 ~ 3 5/32 (20~80mm)
• Tension adjustment should be done only after monitor installation
• Supplied parts and hardware for installation

Product Usage Instructions

Weight Limit and VESA Pattern Check

Check the weight of your monitor (including accessories) to ensure it is between 4.4 – 26 lbs / 2.0 – 11 kg. Verify the VESA pattern of your monitor before installation. The mount is compatible with monitors that have a VESA pattern between 75 x 75mm/3 x 3 (WxH) and 100 x 100mm/4 x 4 (WxH). If your monitor’s VESA pattern is smaller than 75mm x 75mm or greater than 100mm x 100mm, this mount is not compatible with your monitor.

Installation of USB Cable (Optional)

Route the USB cables from Line Out (Female) at the base, to Line In (Male) at your Desktop or Laptop Computer. Loosen pre-installed bolts and detach C Clamp from Brace. Insert bolts through Brace and thread into Base. Tighten with Allen Key. Ensure bolts are secured firmly. Alternatively, insert bolts through Pressure Plate and thread into Base. Tighten with Allen Key. Ensure bolts are secured firmly.
Note: This step is optional and not required for mount functionality.

Tension Adjustment

Adjust the tension only after attaching the monitor to the mount. Do not adjust tension without a monitor attached.

Model: ERDGM2-01 B
Thank You for Choosing this ErgoAV Product!
At ErgoAV, we want to add value to your AV experience by providing the highest quality products and services in the industry. If you have any concerns or comments, please contact us.
ErgoAV Customer Care
phone: (877)419-7832
email: support@ergoav.com
website: www.ergoav.com
address: 9501 Louisiana Ave N, #200, Brooklyn Park, MN 55445

IMPORTANT SAFETY INFORMATION

• Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our Technical Support line at 877-419-7832 or customer service at support@ergoav.com.
• CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
•  This product contains contents under pressure. DO NOT puncture or expose to fire or flame. It is strictly prohibited to dismantle the product. If defective, return to the manufacturer.
• The desk must be capable of supporting three times the weight of the total load (the mount, the monitor and all accessories weight). Don’t use the product on particle board.
• The information contained in this manual does not cover all possible conditions or variables in relation to the install of this product. The information provided in this document is subject to change without notice.

Weight Restrictions If your monitor weighs more or less than the range above, this mount is NOT compatible. Monitor should not exceed maximum listed weight.

WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended for use only within the weight range listed. Use with products heavier than the maximum weight limit may result in failure of the mount, causing potential damage and or injury. It is the responsibility of the installer to verify the total weight of the monitors and any accessories attached. Do Not exceed the weight limit listed.

Check the VESA Pattern of Your Monitor before You Begin the Installation
Measure Your Monitor’s VESA Pattern:
Minimum: 75 x 75mm/3 x 3″ (WxH)
Maximum: 1 00 x 1 00mm/ 4 x 4″ (WxH)
If your Monitor’s VESA Pattern is smaller than 75mm x 75mm or greater than 1 00mm x 1 00mm, this mount is NOT COMPATIBLE with your monitor. Please contact our Technical Support at 877-419-7832 or support@ergoav.com to fmd a compatible mount.

Product Features

TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MONITOR INSTALLATION

Attention
DO NOT adjust tension without monitor attached.

1. Verify the weight of your monitor (including accessories) is between 4.4 – 26 lbs / 2.0 – 11 kg.
2. Monitor weight information can be found within its box or manual.
3. Ensure monitor has been securely attached to the mount.

WARNING:

• Gas Spring Arm is under pressure and should be handled with care.
•  Failure to follow the instructions may result in damage to the mount and/or personal injury.

Tools Needed (Not Included)
For Grommet Mounting (Optional)

• Electric Drill (Optional)

• Drill Bit (Optional)
  7/16-7/8″ (11-22cm)

For Attaching the Monitor Plates to the Monitor

• Phillips Screwdriver

Supplied Parts and Hardware

WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. If you require replacement parts, please contact our Technical Support at 877-419-7832 or Customer Service at support@ergoav.com to fmd a compatible mount.
NOTE: Not all hardware included in this package will be used.

Supplied Parts and Hardware for Step 1

*Step 1 INSTALLATION OF USB CABLE Optional. (Not required for mount

functionality)**

Step 1-1 Route the USB cables from Line Out (Female) at the base, to Line In (Male) at your Desktop or Laptop Computer.
For Clamp Mounting(Optional)
Loosen pre-installed Bolts and detach C Clamp from Brace as shown below.
Option A: Insert Bolts [C] through Brace [Y] and thread into Base [03]. Tighten with Allen Key [E1 ].
Warning:
Ensure bolts are secured firmly.

For Grommet Mounting (Optional)
Option B: Insert Bolts [C] throughPressure Plate [H] and thread into Base [03]. Tighten with Allen Key [E1].
Warning:
Ensure bolts are secured firmly.

Supplied Parts and Hardware for Step 2

Step 2 Assemble the Base

Option A: For Clamp Mounting
Insert bolts on C Clamp into desired holes on Brace and tighten with Allen Key [E1] as shown below.

After Sliding Base Assembly onto desktop, rotate the knob until the C-Clamp is secured firmly to the underside of desktop.
Option B: For Grommet Mounting
If a hole is needed for grommet installation, be sure to leave at least 2″ from the edge of desktop and mark where the hole will be drilled. Use either a 7 /16″ or 7 /8″ drill bit for this step.

Supplied Parts and Hardware for Step 3

Step 3 Attach the Arm Assembly to the Base

Insert Arm [01] into the Base [03] and secure by tightening the set screw with Small Allen Key [E2] as shown below.
WARNING: Do not over-tighten the set screw [M] in order not to affect the rotation of the arm.
Slide Arm Extension [02] onto the Arm [01] and secure by tightening the set screw with Small Allen Key [E2] as shown below.
Supplied Parts and Hardware for Step 4

Step 4 Attach the Monitor Plate to the Arm

Line up the holes from the Monitor Plate and Arm by sliding the Monitor Plate [06] into place from the side of the Arm [01 ]. Secure the Monitor Plate to the Arm with Large Allen Key [E3] Using Bolt [G1] and Washer [G2].
Supplied Hardware for Step 5

Step 5 Attach the Monitor to the Monitor Plate

Option A (For Flat Back Monitor)
5A-1 Turn top two bolts [A] CLOCKWISE until about 0.1-0.2″ (3-5mm) of space is between monitor back and bolt head.

5A-2 Hang the monitor from the Monitor plate with the top two bolts .

Screw the remaining two bolts to the bottom holes. Tighten all bolts evenly.

Option B (For Curved Back Monitor)
5B-1 Slide the spacer [B2] over the bolt [B1] threads. Turn the top two bolts CLOCKWISE until about 0.1-0.2″ (3-5mm) of space between the spacer and the bolt head.

58-2 Hang the monitor from the Monitor plate with the top two bolts.
Place the spacers [82] between the monitor plate and back of monitor. Screw the remaining two bolts to the bottom holes. Tighten all bolts evenly.
Supplied Hardware for Step 6 3/16″ (5mm) Large Allen Key E3 (x1)

Step 6 Adjust the Gas Spring Tension

Ensure the arm is held in a horizontal position (parallel to desktop) during adjustment. Failing to do so may result in difficulty adjusting or potential damage to the mount.
Gas Spring arm is under pressure and should be handled with care. Failure to follow the instructions may result in damage to the mount and/or personal injury.

1. IF the gas spring arm RISES with the monitor attached, hold the arm in a horizontal position while using the large Allen Key [E3] to turn the adjustment bolt CLOCKWISE, REDUCING the arm tension.
2.  IF the gas spring arm LOWERS with the monitor attached, hold the arm in a horizontal position while using the large Allen Key [E3] to turn the adjustment bolt COUNTER-clockwise ‘ INCREASING the arm tension.
   

Step 7 Rotation Restriction

To ensure proper stability, do not adjust monitor behind base. Monitors and arms should remain over the desktop. Failure to do so could result in property damage or injury.

Supplied Hardware for Step 8
****3/16″ (5mm) Large Allen Key E3 (x1)

Step 8 Adjust the Monitor to Proper Tilt Angle

1. Slightly loosen the Bolt with Large Allen Key [E3]
2. Tilt monitor to your desired position.
3.  Re-tighten the Bolt with Large Allen Key [E3] to hold monitor in desired position.
   

Step 9 Route the Cables along the Arm

Supplied Part for Step 1 0

Step 1 0 Attach the Decorative Cover to the L Bracket

At ErgoAV, we strive to provide the highest value products.
We want to support your purchase.
If you have questions, concerns, or feedback please let us know!
ErgoAV Customer Care
Phone(877)419-7832
support@ergoav.com
9501 Louisiana Ave N, #200, Brooklyn Park, MN 55445
www.ergoav.com

References

• ErgoAV

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>