Rasonic RSS-B12 Mini Ceramic Stewing Mug Instruction Manual

June 11, 2024
Rasonic

Rasonic-logo

Rasonic RSS-B12 Mini Ceramic Stewing Mug

Rasonic-RSS-B12-Mini-Ceramic-Stewing-Mug-product

Important Safeguards

When using the appliance, make sure to follow the below safety precautions:

Before use

  1. Read the operation manual before using the appliance. Failure or negligence in following these safety precautions could cause fire, electrical shock or injury.
  2. Remove and discard all packing materials of the appliance. Make sure children do not play wrth them to avoid any danger.
  3. Before connecting to the electricity, check if the rated voltage on the appliance corresponds to the local voltage. To avoid overload, do not connect the appliance in the same power socket with other high power consumption appliances. Make sure the appliance is connected to power socket with grounding.
  4. To avoid any hazard, make sure the plug is dry before use.

In operation

  1. Never leave the appliance unattended when in use or operate without water.
  2. Do not cook inside the water tank (heating plate) directly.
  3. Do not operate the appliance in the following places:
  4. Humid environment or near water sources
  5. Near heat and fire sources (such as electric oven and induction cooker etc.)
  6. Unstable and insufficient support surface
  7. Near inflammable or non-resistant to heat objects (e.g. carpet, plastic, table cloth, curtain and towel etc.)
  8. Sufficient room must be reserved for steam or air bubbles generated, and amount of water should not exceed the maximum water level “ti~7J<Ul.” of the water tank. Otherwise, water and steam may spill out during operation and cause dangers.
  9. Water may splash out from the edge of lid during operation. To avoid fire, electrical shock or injury, do not operate the appliance near the other appliances or electric socket extension.
  10. Make sure the lid is closed tightly to prevent water from splashing out or steam discharging; otherwise, the appliance may not function properly or cause hazards.
  11. WARNING: Do not open the lid during operation or right after use, as massive steam will come out from the steam hole, only by doing so can prevent steam burn.
  12. Do not open the lid during operation, otherwise boiled water may spill out and cause burns. If necessary, press [Function/Cancel] button to switch off the appliance before open the lid. Be careful of the hot steam and droplets when open the I id.
  13. After cooking, a lot of vapour and water droplets will remain inside the body and lid, which is a normal phenomenon. To avoid burns, switch off the appliance and unplug the power, wait for a while before opening the lid to avoid burn by residue heat. Open the I id carefully to avoid condensed water droplets from the lid onto the control panel or power cord. To avoid scalding by hot steam, use oven mitts to pick up the food from the appliance.
  14. Always use kitchen utensils with long handles when checking the food inside. Beware of hot steam, do not operate the appliance next to wall or furniture.
  15. Do not switch on the appliance when there is no water in the water tank. If over heating occurred, add water into the water tank or unplug the power.
  16. Do not open the lid, move or shake the appliance during operation as to avoid massive steam emission resulting in burns or other hazards.
  17. To avoid appliance malfunction, deformation or discoloration, do not cover the appliance or steam vent by any object when using the appliance.

After use

  1. Unplug the appliance from the socket and let the appliance cool down before moving, cleaning and repairing.

  2. To avoid getting burned, never touch the product enclosure and heating plate which are subject to residual heat right after use.

  3. To prevent electric shock and fire, never immerse the main body,
    power cord or plug in water or let them wet. Make sure the plug is dry before use.

  4. Disconnect the power plug when the appliance not in use for long time, preventing electric leakage and electric shock due to insulation degeneration. Do not touch, plug or unplug the appliance by wet hands which can result in electric shock.

Beware of the following

  1. The appliance equipped with boil-dry protection system. If water inside the pot completely evaporated or temperature exceeds the protection level, the operation will stop while error code will show on display. If the appliance was boiled dry once, switch off and lift the main body from the power base and cool down completely before reuse. CAUTION I Boil-dry protection is the device for protection. Do not rely on this function to switch off the appliance.
  2. The appliance is not intended to be operated by means of an external timer or separated remote control system, as to prevent short-circuit or other flammable hazards.
  3. Do not let the ceramic mug withstand big temperature difference. (For example: Heat the ceramic mug with fire or put the hot ceramic mug on a marble surface or into cold water), otherwise the mug may crack because of thermal expansion and contraction.
  4. To prevent water tank and ceramic mug corrosion, avoid cooking any substance that is acidic or alkaline.
  5. The ceramic mug is a kind of fragile ware. Use it carefully. Do not hit the mug or drop it from a high place to avoid damage.
  6. Great care is necessary in using the appliance, especially near children. Children should be supervised to ensure that they do not play with the appliance. Also, children without adult supervision should not operate the appliance. Keep them away from the appliance and its power cord.
  7. Handle the power cord with care. Do not place heavy objects on the power cord. Never clip, modify, stretch or twist the power cord. Do not grasp the power cord but the plug i15elf when plug in or unplug the appliance. Ensure that the power plug fi15 all the way into the appliance socket, fail to do it may cause electric hazard.
  8. Do not operate the appliance when the power cord is tangle or hang over the edge of a table, countertop or let it touch any hot surface. It may cause power cord damage.
  9. Always wipe off any dust from the power plug and clean the appliance, make sure it is not oily, especially on the pins such to prevent fire from happening.
  10. Do not use the appliance for purposes other than cooking. (If the appliance is not used for cooking, it may cause malfunction and hazard.)
  11. The appliance can be ~ by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  12. The appliance is intended to be used in household or similar applications such as staff kitchen areas in shops, offices and other working environments. Do not use it outdoors.
  13. Always check the condition of the appliance, ceramic mug, power cord and plug. To avoid hazard, stop using the appliance immediately if the appliance is damaged or dropped. Contact Shun Hing Electric Service Centre Limited for checking and repairing.
  14. Do not use, replace or assembly any parts which is not produced under authorization, otherwise, the warranty becomes invalid and our company will refuse any liability and repairing cost for the damage caused.
  15. To comply with safety regulations and avoid hazards, if repair is needed, present the official invoice, warranty card (printed on the gift box and must be saved it for future reference) with the appliance for repair service and contact Shun Hing Electric Service Centre Limited hotline at 2406 5666. Address can be found at the back page of the manual.

Cleaning and Storage Guideline

  1. Before cleaning, unplug the appliance and let it cool down completely.
  2. Ceramic mug is a kind of fragile ware, handle with care and do not place in high temperature environment for a long time.
  3. Use warm water together with mild detergent to clean the ceramic mug. Never use poisonous or corrosive detergent for cleaning.
  4. To avoid malfunction and dangers, do not clean the main body with water directly or let water penetrate inside the main body.
  5. To remove the odor, add some water to the ceramic mug and the water tank turn on the appliance until water boiled. Pour out the water and wait until the appliance cool down completely. Then wash it with warm water.
  6. Due to the minerals in water, color scale will be found on the heating plate after heating. The harder the water, the quicker the scale will be formed. It is a normal phenomenon and will not affect the operation.
  7. To remove the water scale, follow the below instructions:
  8. Fill water into the water tank (250m I of water recommended)
  9. Put halved sliced lemon in the water tank (Or, follow the ratio to add 20g citric acid per 1 L water).
  10. Operate “Steam” function until the water boiled. Press the [Function/Cancel] key to stop the operation, wait and pour out all water after around 20 minutes. Then clean the heating plate with a sponge or soft brush, and rinse by water at the end.
  11. NOTICE  To remove the remaining smell of citric acid, boil water again and pour it out afterward.
  12. Never clean the appliance by using gasoline, cleanser or harsh cleaning tools (e.g. metal brush).
  13. If dirt is attached on the water tank, main body or lid, use a damp cloth to clean and wipe them dry.
  14. Always let the appliance cool down completely before storage. Put it in a paper box and store in a dry environment. Never wrap the power cord tightly around the appliance or put pressure on it to avoid the power cord damage.

Product Specifications

  • Model No: RSS-812
  • Rated Voltage: 220-240V- 50-60Hz
  • Rated Power: 200W
  • Ceramic Mug Capacity : 1.2 L
  • NetWeight Approx: 2.06 kg
  • Product size Nil x D x H): 218 x 247 x 178 mm

Control Panel and Product Structure

  • Control Panel****

Rasonic-RSS-B12-Mini-Ceramic-Stewing-Mug-fig-1

  • Product StructureRasonic-RSS-B12-Mini-Ceramic-Stewing-Mug-fig-2
  • Operation Time TableRasonic-RSS-B12-Mini-Ceramic-Stewing-Mug-fig-3

Operation Instructions

Before First Use

  1. When the first time of use, it may have smell due to the new packing. It is a normal phenomenon where the smell will gradually disappear with time.
  2. Make sure the appliance is not plugged, and depend on the cooking functions. follow the instruction stated in “Chapter 5.2 Preparation” and “Chapter 5.3 A.mctlon Selectlon” to operation the appliance.

Preparation

  • CAUTION: Clean the ceramic mug by water before using. Do not exceed the maximum water level n:ftiii’J.Jcf.il” of the water tank when filling water.
    Only use distilled water or tap water, never use mineral water as it will fasten the formation of scale.

Stewing functions (“Quick” Stew & “Slow” Stew)

  1. Put appropriate amount of ingredients and water into the ceramic mug supplied, and close the ceramic lid.
  2. Place the ceramic mug into the main unit.
  3. Add water to the maximum water level of the water tank, and close the lid finally.

NOlE:  To avoid the power plug from getting wet by the water droplets, lift the lid vertical when open. To avoid water droplets dripping off onto the power cord and control panel, upside down the lid when lifting and let water droplets backflow to the lid.

Steaming fundlon (“Steam”)

  1. Pour water into the water tank (Water added just cover the saddle-platform is suggested, approx. SOOmO.
  2. Put the steam plate inside the main body. Place the food directly on the plate and cover the lid (If the ingredients will generate juice after heating, make use of a container).
  3. Close the lid finally.
    ATTENTION: During operation, a lot of vapor and water droplets will be generated; to avoid affecting the cooking result by water dropping onto the food, make use of heat-resistant cling wrap to seal the container.

5.3 Function Selection

  1. After connecting to the electricity, a “Di” sound will be heard. The display will show “–” representing the appliance is in standby mode. Press [ Function/Cancel ] key to select desired function where “Quick”-> “Slow”-> “Steam”-> “Warm”-> Standby(–) mcx:le will show in order. Function indicators will flash accordingly while default operation time will show on the display.
  2. After choosing the cooking function, press the [ + ] and ( – ] keys to adjust desired operation time. Once finish, wait for about 10 seconds to confirm. Related function indicator will change from flash to light up and the operation will start.
  3. When the operation completed, “Di Di Di Di” sounds will be heard. “EE” will flash on display and the appliance will switch to keep warm mode after about 1 minute. uEE” on the display wi II change from flash to light up accordingly.
  4. If no keep wam, function is needed, pre$ the [ Function.Cancel ] key to cancel during warm keeping. “- -” will show on display and the appliance will change to standby mode.
  5. Suggested to wait for about 5 minutes before opening the lid and taking out the food, as it can avoid bums by water spilling.

CAUTION: The appliance will automatically turn off if water inside the water tank evaporated during operation or warm keeping. The appliance will emit “Di Di Di Di” sounds and 11EO” will flash on display at the time when the operation suspended. The appliance will return to standby mode if refill water or let it cool down naturally such that temperature drops below protection value. Reuse the appliance by selecting a cooking function again.

Preset function (The time to start the operation)
Fol low the procedures described in “Charier 5.2 Preparationn, place the ingredients and water into the ceramic mug, and follow the steps below to preset the cooking function.

NOTE: Perishable foods are not recommended for long preset time as to avoid deterioration. For example: Preset 6 hours “Slow” function for 5 hours.

  • After connecting to the electricity, “–” will show on the display representing that the appliance is in standby mode.
  • Pre$ the ( Preset l key once, the preset indicator will flash and the default preset time “2.0” will show on display. Pre$ the [ + ] key to adjust the time setting to “6.0” (6 hours).
  • Pre$ the [ Function/Cancel ] key to select the “Slow” function, corresponding indicator will flash and “Preset” indicator will light up. Display will show the default cooking time “4.0” (4 hours). Press the [ + ] key to adjust the cooking time setting to “5.0” (5 hours).
  • Wait for about 10 seconds to confirm the setting and “Preset” function will start.
  • After 6 hours elapsed, “Slow” function will start for 5 hours until the operation completed. “Di Di Di Di” sounds keep operating will be heard and “EE” will flash on display. The appliance will switch to keep warm mode after about 1 minute. “EE” on the display will change from flash to light up at the same time.
  • Warm keeping will continue until water inside the water tank evaporated. Detailed information can be found in “Chapter 5.5 Keep Wann Function”.

Keep Wann Function

  • The appliance will change to keep wann mode automatically after the operation completed. No defined operation time for warm keeping, so the appliance will tum off until the water inside the water tank evaporated. uo1 DI DI DI” sounds wlll be heard and “EO” wl be shown on dlsplai the appllance will then turn off automatically after 40 seconds.
  • User can press the [ Function/Cancel ] key to select “Keep Wann” function, related indicator will flash, and “EE” wlll show on display. Keep warm function will start operating after 10 seconds.
  • If keep warm function Is not necessary during operation, pres.s the [ Functton/Cancel ] key once, ” – -” will be shown on display representing the appliance is in standby mode. User can unplug the power now

ATTENTION: Do not warm perishable foods for too long, otherwise, it may generate odor and get deteriorated.

Cancel Function
To cancel a cooking function, user must pr~ the [ Function/Cancel l key after the confinnation {which means after the related indicator changing from flash to light up), the set cooking function will be cancelled. “–“will show on display and the appliance will return to standby mode.

Troubleshooting and Treatment

If the following situation happens, unplug the appliance immediately. Contact and report to Shun Hing Electric Service Centre Limited for checking and repairing.

  1. If the power cord or power plug is abnonnally hot.
  2. If the electricity flows discontinuously when the power cord is bent.
  3. If the appliance is abnormal hot or if you smell smoke or scorching.
  4. If you get shocked when touching the appliance.
  5. If the appliance sometimes does not turn off automatically.
  6. If water is leaking out from the appliance.

Special Avowal

  1. The content in the operation manual has been checked. Our company reserves the hermeneutic power to any printing errors or misunderstanding on the content.
  2. If there are technical improvements on the appliance, the operation manual will be updated in new version without prior notice. The product appearance and specification are subject to the manufacturer information.
  3. In case there is any inconsistency or conflict between the English versions and Chinese versions of the tenns, the Chinese versions shall prevail.
  4. E-copy of user manual can be sent by e-mail on request, please call Shun Hing Electric Works & Engineering Co., Ltd. at 2861 2767.\

After Sales Service

  1. For any defect, in the judgment of technician from Shun Hing Electric Service Centre Limited, caused under normal use, our company is responsible for repairing or replacing any parts of the said electrical appliance free of charge within one year guarantee period commencing from the date of purchase. Any defective part which has been replaced shall become our property. Warranty service does not cover the repair or replacement of consumable parts {including ceramic mug, ceramic lid, steam plate, lid, control panel sticker and power cord, etc.). If the appliance is used improperly, for commercial (or semi-commercial) use, or not following the instructions in the operation manual, the warranty becomes invalid and our company will refuse any liability and repairing cost for the damage caused.
  2. User must present the official invoice/redemption voucher and the product warranty card {printed on gift box, and must be saved it for Mure reference) with the chop from sales point/ redemption center for maintenance. For enquiries, please call Shun Hing Electric Service Centre Limited hotline at 2406 5666.

Customer Service Centre

  • 1/F, Shun Hing Centre, 2 Shing Yiu Street, Kwai Chung, N.T.
  • 9/F., Block B, Peninsula Centre, 67 Mody Road, Tsim Sha Tsui East, Kowloon
  • 22/F, Parkview Centre, 7 Lau Li Street, lin Hau, Hong Kong
  • Avenida de Venceslau de Morais, No. 193-199,5 andar – I, Edf. Industrial Nam Leng, Macau

For the latest information of Hong Kong and Macau service center, please visit http://www.shesc.com/en

SHUN HING ELECTRIC WORKS AND ENGINEERING CO., LTD.

Address: Office: 9/F, Peninsula Centre, 67 Mody Road, Tsimshatsui East, Kowloon, Hong Kong
Tel: 2861 2767 Fax: 2865 6706
Website: htt://www.rasonic.com
E-mail: shew@shunhinggroup.co

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals