ERGOAV ERMTX1-01B Tilt TV Mount Instruction Manual
- June 13, 2024
- ERGOAV
Table of Contents
Tilt TV Mount Instruction Manual
Model:
ERMTX1-01B
ERMTX1-01B Tilt TV Mount
THANK YOU FOR CHOOSING THIS ERGOAV PRODUCT!
At ErgoAV, we want to add value to your AV experience by providing the highest
quality products and services in the industry. If you have any concerns or
comments, please contact us.
ErgoAV Customer Care
phone 877-419-7832
email: support@ergoav.com
website: www.ergoav.com
address: 9501 Louisiana Ave N, #200, Brooklyn Park, MN 55445
Important Safety Information
DANGER! Please carefully read all instructions before attempting
installation. If you do not understand the instructions or have any concerns
or questions, please contact our Technical Support line at
877-419-7832 or customer service at
support@ergoav.com.
CAUTION: Use with products heavier than the maximum weights indicated may
result in instability causing possible injury.
- Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
- This product is designed for use in wood stud, and solid concrete walls. – DO NOT install into drywall alone.
- The wall must be capable of supporting four times the weight of the TV and mount combined.
- Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Do not use outdoors.
- Route cords and cables properly to avoid mechanical damage.
- SAVE THESE INSTRUCTIONS.
Weight Restrictions
If your TV weighs more, do not use this product.
DO NOT exceed the maximum weight indicated. This mounting system is intended
for use only within the maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of the mount and its
accessories, causing damage and or injury.
Check the VESA Pattern of Your TV before the Installation
100 mm ≈ 4 in
200 mm ≈ 7 7/8 in
400 mm ≈ 15 3/4 in
600 mm ≈ 23 5/8 in
If your TV’s VESA Pattern is smaller than 200mm x 100mm or greater than 600mm
x 400mm, this mount is NOT COMPATIBLE with your TV. Please contact our
Technical Support at 877-419-7832 or
support@ergoav.com to find a compatible mount.
Tools Needed (Not Included)
Verify
Your Wall Construction 
If you are not sure of the wall construction, please contact our Technical Support line at 877-419-7832 or customer service at support@ergoay.com.
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. If you require replacement parts, please contact our Technical Support line at 877-419-7832 or customer service at support@ergoay.com
- Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1 
Step 1 Secure the TV Brackets to the TV
Select TV Bolts
Only one bolt size fits your TV. 
Bolt length: Verify adequate thread engagement with
bolts or bolts/spacers combination. We recommend thread engagement by at least
5 turns.
- Too short will not hold the TV.
- Too long will damage the TV.
Note: Please do not over tighten the TV bolts to avoid damaging your TV.
Please Note: When using the spacers it is important to note that they can
be used in multi-layers (meaning stacked). If you have any difficulty
understanding how to install the TV bolts or spacers, please contact our
Technical Support line at 877-419-7832
or customer service at support@ergoav.com.
Parts Needed if You Have a TV as Shown Below
CAUTION: When attaching the TV mount to the
back of the TV, make sure the drawstring ends at the end of the TV and is
centered on the back of the TV.
PLEASE NOTE: The bolt hole locations on your TV may vary in accordance of
the manufacturers design of the TV. We are only illustrating possible
locations of the bolt holes.
Option A (For Flat Back TV)
NOTE: The drawstring ends should point towards the
end of TV. Knobs should ‘ face out toward edge of TV.
Phillips Screwdriver (Not Included)
Option B (For curved back TV)
Spacers must be tall enough so that the curve on the back of the TV will not
interfere with the mounting plate. 
NOTE: The drawstring ends should point
towards the end of TV. Knobs should face out toward edge of TV.
Refer back to spacer instructions on page 5, if needed. 
Option C (For TV with A
“Bump”)
Spacers must be tall enough so there is no gap between TV bracekt and bump on
the back of the TV.
Phillips Screwdriver (Not Included) 
NOTE: The drawstring ends ‘ should point towards the end of TV. Knobs
should face out toward edge of TV.
Refer back to spacer instructions on page 5, if needed. Option D (for TV with Cable
Interference)
For cable interference, use spacers [F1], [F2] and [F3] to create extra space
between the TV and TV brackets.
Phillips Screwdriver (Not Included) 
Refer back to spacer instructions on page 5, if needed. Option E (For Recessed Holes)
The spacer needs to fill in the recessed holes on the back of the TV so that
the TV brackets are as close to the TV as possible.
Phillips Screwdriver (Not Included) 
Refer back to spacer instructions on page 5, if needed. Supplied Parts and Hardware for
Step 2
Note: The lag screw is shown in actual
size |
Wall Anchor 10X60mm
CAUTION!
This anchor is for concrete walls ONLY. DO NOT use them in drywall or wood
studs. Step 2 Attach the Wall Plate [01] to the Wall
For wood stud installation, follow STEP 2A
For concrete installation, follow STEP 2B
Step 2A Wood Stud Option
WARNING:
Do not use a drill for tightening the Lag Screws [A1]! Only use a socket
wrench.
Avoid potential personal injury or property damage! DO NOT over-tighten the
Lag Screws [A1]. Tighten the Lag Screws [A1] only until they are pulled firmly
against the Wall Plate [01].
DO NOT USE ANCHOR [A2] FOR THIS STEP.
Ensure the wall plate is securely fastened to the wall before continuing to
the next step.
- Nominal wood stud size: common 2 x 4 in (51 x 102 mm)
- Stud center must be verified.
Use a
stud finder (not included) to locate wood studs or use an awl (not included)
to verify the edges. Mark the edge and center locations. 
Position the Wall Plate Template [04] at your
desired height and line up the holes with your stud center line. Level the
Wall Plate Template [04] and mark the holes. Drill pilot holes using a 7/32 in (5.5mm) diameter
drill bit. Make sure the depth is not less than 2 3/4 in (70mm).
Note:
Do not use a drill to tighten the lag screws. Only use a socket wrench.
Install
the Wall Plate [01] using Lag Screws [A1]. Tighten the Lag Screws [A1] is
pulled firmly against the Wall Plate [01]. DO NOT over-tighten the Lag Screws
[A1].
Step 2B Solid Concrete Wall Option
**WARNING:**
Do not use a drill for tightening the Lag Screws [A1]! Only use a socket
wrench.
- Avoid potential personal injury or property damage! DO NOT over-tighten the Lag Screws [A1]. Tighten the Lag Screws [A1] is pulled firmly against the Wall Plate [01].
- Ensure the wall plate is securely fastened to the wall before continuing to the next step.
- Mount the wall plate directly onto the concrete surface without any covering.
- The thickness of the concrete wall must exceed 5.5 in (140 mm).
Position
the Wall Plate Template [04] at your desired height. Level the Wall Plate
Template [04] and mark the pilot hole locations. 
Drill 4 pilot holes using a 3/8 in (10mm) diameter drill
bit. Make sure the depth is not less than 3 in (75mm).
Use the hammer to knock Wall Anchors [A2]
into the wall. Be sure the Wall Anchors [A2] are seated flush with the
concrete surface. 
Install the Wall Plate [01] using Lag Screws
[A1]. Tighten the Lag Screws [A1] is pulled firmly against the Wall Plate
[01]. DO NOT over-tighten the Lag Screws [A1].
Note: Do not use a drill to tighten the Lag Screws [A1]. Only use a
socket wrench.
Supplied Hardware for Step 3 Step 3
Insert Cable Clips [05] on the top or bottom of the Wall Plate [01] as
needed.
Step 4 Secure the TV onto the Wall Plate
To Hang TV onto the Wall Plate [01]
- Hang the TV with Brackets [02] and [03] onto the Wall Plate [01].
- Gently press the bottom of the TV towards the wall until you hear the safety locks “click” into place on both sides of the mount.
Cution: to avoid potential injury and person property damage, two people
should assist in removing the TV from the mount.
- Verify that all cables are disconnected from the back of the TV and the TV is unplugged from wall.
- While gently applying pressure to the front of the TV towards the wall, pull down on the safety straps until they are full disengaged.
- While keeping the straps in the disengaged position, move the bottom of the TV away from the wall and lift the TV off the wall plate.
Supplied Hardware for Step 5 
Step 5 Adjustment
Tilt Adjustment
- Use tension knobs on the sides of the TV brackets to allow adjustment of the TV to desired position.
- After making any adjustments, always re-tighten the tension knobs to hold TV in place and avoid unwanted movement.
At ErgoAV, we strive to provide the highest value products.
We want to support your purchase.
If you have questions, concerns, or feedback please let us know!
ErgoAV Customer Care
Phone 877-419-7832
support@ergoav.com 
9501 Louisiana Ave N, #200, Brooklyn Park, MN 55445
www.ergoav.com
860-00101-01 Rev00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>