OPTEX AP-20NBR(C) Indoor Recessed Mount PIR Detector Instruction Manual

June 1, 2024
OPTEX

OPTEX-LOGO

OPTEX AP-20NBR(C) Indoor Recessed Mount PIR Detector

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-1

Specifications

  • Model: AP-20NBR(C)
  • Mounting Type: Indoor Recessed
  • Detection Area: 6.0m (20′) curtain detection area at 4.5m (14′ 9″) mounting height

Product Usage Instructions

Before Installation

Manufacturer’s Statement:
Warning: Failure to follow the provided instructions may cause serious injury.

Parts Identification

  • Top Cover
  • Lens
  • Base Cover
  • JP2 PIR Sensitivity
  • JP1 Alarm Output Mode
  • SW1 Tamper Switch
  • JP3 Battery Saving Timer

Settings

  1. Disassemble the base cover to set the detector.
  2. Adjust Jumper Pin settings for Alarm Output Mode, PIR Sensitivity, and Battery Saving Timer.
  3. Reassemble the base cover securely.
Installation

Ceiling Mount Without Switch Box

  1. Install retaining springs on both sides as illustrated.
  2. Insert the detector into the hole ensuring the retaining springs are positioned correctly.
  3. Arrange wires with a downward slope to prevent water ingress.

Ceiling Mount With 86-Type Box

  1. Prepare an 86-type box on the ceiling.
  2. Install the detector into the 86-type box and secure with screws and screw caps.

FAQ

  • What is the recommended mounting height for the detector?
    The recommended mounting height is between 2.5m to 4.5m (8’2″ to 14’9″).

  • How can I adjust the PIR sensitivity of the detector?
    Use Jumper Pin JP2 to adjust the PIR sensitivity to High (H), Medium (M), or Low (L).

  • Can the detector be used outdoors?
    No, outdoor installation is not recommended as it may lead to performance issues.

Before installation

Manufacturer’ s statement

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-2
PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-3
PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-4
PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-5

Parts identifications

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-6

Accessories

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-7

Settings

  1. Disassemble
    Open the base cover, and to set the detector.

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-8

  1. **Jumper pin settings

**PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-9

  1. Assemble
    Close the base cover, and fasten the screw to fix the cover.

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-1

Installation

Ceiling mount without switch box

  1. Install a retaining spring on both sides.
    (follow the illustrated arrow steps to complete the assembly of the retaining spring.)

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-11

  1. Make a ø45 mm (1.77”) hole in the ceiling for mounting.

  2. Insert the detector into the hole so that the retaining springs come first.

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-13

Ceiling mount with 86-type box

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-14

NOTE
For the 86-type box mount, dual 86-type boxes are recommended with the additional one used to accommodate the transmitter.

  1. Prepare an 86-type box on the ceiling.

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-16

  1. Install the detector into the 86-type box.

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-17
NOTE
Align the bump with the triangle recess as illustrated in the figure.

  1. Fix the detector with two screws and cover their heads with two caps.

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-19

Wiring

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-20

Checking

Walk test

  1. Power on.

  2. Wait for 60 seconds to complete the warm-up time.

  3. Walk in the detection area to check the detecting performance.

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-24

  1. Start operation.

OTHER

Specifications

Model AP-20NBR(C)
Detection method Passive infrared

Detection area

| < Ceiling mount >

6.0 m x 1.0 m (20’ x 3’3”)

at 4.5 m (14’9”) height

| < Wall mount >

6.0 m x 4.5 m (20’ x 14’9”)

at 1.5 m (4’11”) height


Mounting height

| 2.5 m to 4.5 m (8’2” to 14’9”)| 1.5 m (4’11”): Horizontal

1.0 m (3’3”): Vertical

Mounting type| Recessed ceiling mount/ Wall mount/ 86-type box mount
Sensitivity| 2.0℃ at 0.6 m/s (3.6°F at 2’/s)
Detection speed| 0.3 to 3.0 m/s (1’/s to 9’10”/s)



LED indicator

| Warm-up upon power on: blinking Stand-by: off

Walk test: solid on

Alarm: off

Alarm cycle| Approx. 2 s
Battery saving timer| 120 s/ 5 s selectable
Alarm output| N.O./N.C., 3.6 V DC 10 mA max.


Tamper switch

| N.C. 28 V DC 100 mA max.

The contact opens once the casing is detached.

Warm-up time| Approx. 60 s
Power supply| 2.7 to 3.6 V DC (CR123A battery)


Current

| 3 V DC

Stand-by: 10цA, Max.: 4 mA

PIR sensitivity| H/ M/ L
Weight| 50 g (1.76 oz)
Operation temprature| -20 to +50℃ (-4°F to +122°F)
Operation humidity| < 95%
Location| Indoors


Dimensions

| ø52 x 35.5 mm (ø2.05 x 1.40 in.): without switch box mount
86 x 86 x 36.5 mm (3.39 x 3.39 x 1.44 in.): with 86-type box mount

  • Specifications and designs are subject to change without prior notice.
  • These units are designed to detect an intruder and activate an alarm control panel. Being only a part of a complete system, we cannot accept responsibility for any damages or other consequences resulting from an intrusion.

Dimensions

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-26

Detection area

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-27
PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-28

Timing chart

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-29

Troubleshooting

PTEX-AP-20NBR-C\)-Indoor-Recessed-Mount-PIR-Detector-
FIG-30

ABOUT COMPANY

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals