Vorago BT 350 Headband Foldable Hands-Free Radio Headphones Instruction Manual

Vorago BT 350 Headband Foldable Hands-Free Radio Headphones

Product Information

• Specifications:
  • Connector: BT 5.3 / TF Card / Aux 3.5 / FM
  • Charging Time: 2.5 hours
  • Voltage: DC 5V
  • Frequency: 2.402~2.480GHz
  • Range: 10 meters
  • Speaker Diameter: 40mm
  • Speaker Impedance: 32 ohms
  • Speaker Sensitivity: 118+/-3dB
  • Warranty: 12 Months (36 Months with conditions)*

Product Usage Instructions

• Functional Operation:
  • Reset Headphones: Under disconnected status (pairing mode), double-click the multifunction button.
  • Power On: Press the power button for 2 seconds. Red and blue lights will flash alternately in BT mode.
  • Power Off: Press the power button for 3.5 seconds.
  • Light ON / OFF: Press the power button for 2 seconds to switch the light on or off.
  • Play/Pause: Short press the multifunction button to play or pause music.
  • Volume Up/Down: Click the corresponding buttons to adjust volume.
  • Previous/Next Track: Long press the buttons to navigate tracks.
• TF CARD Mode:
  • Insert a TF card to enter TF card mode; headphones will play music automatically with a voice prompt.
  • Remove the TF card for Radio mode; press the + and – buttons simultaneously for 2 seconds to switch between BT/Radio mode.
• AUX Mode:
  • Connect the aux cable to enter AUX mode; note that buttons on the headphones will not work in this mode.
• BT Connection Mode:
  • Power on the headphones and enter pairing mode to connect the BT device.
  • Pair with the device by selecting HPB-350 from the BT search and following the prompts.
  • If not connected within 5 minutes, headphones will turn off automatically.
• Charging Indicator:
  • While charging, the red light is steady on; turns off when fully charged. Blue and red lights flash alternately during pairing.
• Security and Maintenance:
  • Ensure proper care and maintenance of connectors and components. Refer to the user manual for detailed instructions.

FAQs

• Q: How do I switch between different modes on the headphones?

  • A: Follow the specific instructions for TF CARD, AUX, and BT connection modes as outlined in the user manual.

• Q: What should I do if the headphones do not pair with my device?
  

  • A: Make sure the headphones are in pairing mode and follow the correct steps for BT connection. Ensure the device is compatible and within range.

KNOW YOUR DEVICE

1. Volume +/ next tack
2. Volume -/ Previous track
3. Switch / Multi-function button (Pause, play, answer the call, redial the last number, light switch, on/off light)
4. Type C charging port
5. TF card
6. Indicator light
7. 3.5 mm auxiliary connector TF Card
8. Microphone
9. LED light

HOW TO USE

Functional Operation

• Reset Headphone: Under disconnected status ( pairing mode) double click the 3
• Power On: Press the 3 for 2 seconds, with the voice prompt “Power on, BT mode” The indication red and blue lights flash alternately, it powers on successfully.
• Power Off: Press the 3 for 3.5 seconds, with the voice prompt “power off” the indicator lights turn off, and it powers off successfully.
• Light ON / OFF: Press the 3 for 2 seconds to switch the light on or off. with a prompt beep.
• Play: Short press the 3 (pause status)
• Pause: Short press the 3 (play status)
• Volumen Up: Click the 1
• Volumen Down: Click the 2
• Previous track: Long press the 2
• Next track: Long press the 1

TF CARD mode

It would into the TF card mode, after inserting the TF card, there is a voice prompt “ TF card mode” and the headphones will identify and play music automatically.

Radio mode

1. Press the “´+” and “-” buttons for 2 seconds at the same time to enter radio mode, with the voice prompt “ Radio mode”. In radio mode, short press 3 for channel searching, and long press 1 or 2 for channel switching.
2. In TF card mode, take out the TF card, and there is a voice prompt “Radio mode” It enters Radio mode automatically, Meanwhile, simultaneously press the “+” and “-” buttons for 2 seconds to switch between BT/Radio mode.

AUX MODE

• 3.5 mm jack for AUX mode.
• Connect the aux cable to the headphones with devices, it will enter the Aux mode.
• ( Note: when the headphone connects with the au cable, it powers off and the buttons on the headphone will not work, this is normal.)

BT connection mode

1. Power on eh headphones and you can hear the voice prompt “Power on, BT mode” It enters the pairing mode, ready to connect the BT device.
2. Open device BT Search “HPB-350”, click and connect it ( when the earphone and device connect successfully, the indicator blue light is on and you can hear the prompt tone “connected”)
   • Note: if the headphones power on without being connected to the device in 5 min, it will turno off automatically. when the battery is low, there will be a voice, prompt, and please charge your headphones timely.
   • While charging, the red light is steady on: Once fully charged, the light turns off; When pairing, the blue and red light flash alternatively.

SECURITY AND MAINTENANCE

• Keep the product dry, do not expose it to humid environments to avoid a short circuit.
• Do not expose it to the sun or high temperatures. High heating will shorten the life of electronic components, damage the battery and deform some plastic parts.
• Do not place it in extreme cold circumstances to avoid damage to the PCB board.
• Do not attempt to disassemble the product.
• Do not throw it, vibrate strongly or hit it with hard objects, to avoid damage to the internal electronic circuit.
• Do not use products with high chemical content or detergent to clean the item.
• Do not scratch the surface with sharp items to avoid damaging the casing and appearance.
• Do not charge it for more than 10 continuous hours to prolong the life of the battery.

DATA SHEET

Limited product warranty

• Vorago equipment and/or accessories are covered by a limited warranty for the time indicated in the annexed validity table, counting from the date of acquisition, against any manufacturing and operation defect, provided they have been used under normal conditions of use during the warranty period and for which it was manufactured.
• Vorago warranty the buyer the absence of anomalies regarding the materials.

12 Months
LCD Monitor

• Except in panel (screen display) for which it will only be 12 months.

| 36 Months*
Computer equipment 3 years including Nanobay 3.

• Except for computer equipment where the processor is integrated into the motherboard it will only be 12 months.

| 36 Months *

Important warranty policy: Please read and complete this warranty policy and seal it in the store when purchasing the product.

Product: Headphone BT|
---|---
Model: HPB-350| Dealer stamp
Brand: Vorago
Serial number:
Invoice number:
Delivery date:

Responsibilities

• The total responsibility of Vorago will be to repair or replace the product, including labour and parts, at no cost to the buyer when it is returned to the point of sale, presenting this warranty policy properly completed and stamped by the establishment where it was purchased.
• The product or copy of the receipt or receipt or invoice, in which data of the product and the date of purchase is specified, to verify the times within the warranty.
• Vorago may use new parts, restored or used in good condition to repair or replace any product, at no additional cost to the consumer.
• In the case of equipment and/or accessories that can not be repaired, the change will be generated by a similar product or with superior characteristics.
• This warranty covers the transportation expenses of the product derived from its fulfillment; which will be directly attributable to the supplier of the product.
• In all replacement products, the original warranty period will be renewed.
• Vorago is governed by international standards for the manufacture of products.

How to obtain warranty support

Warranty claims are processed through the point of sale, during the first 15 days after the purchase, as long as they meet the requirements. Guarantee claims that can not be processed through the point of sale and any concerns related to the product purchased should be sent with the prepaid guide by Vorago to the address of the Vorago headquarters in Francisco Villa No. 3, Col. San Agustín, CP 45645, Tlajomulco de Zúñiga, Jalisco, Mexico. Except in situations of force majeure or fortuitous event, the repair time in no case will be greater than 30 calendar days from the date of receipt of the equipment in Vorago.

Exclusions This warranty is valid in the following cases:

• a) When the product had been used in conditions other than normal.
• b) When the product has not been operated per the instructions for use.
• c) When the product has been altered or repaired by unauthorized persons by Vorago.

Vorago does not offer any other express warranty for this product. To make the warranty valid, as well as the acquisition of parts, components, consumables and accessories

To validate a warranty, the following information must be sent to the email: garantias@voragolive.com.

1. Model and colour
2. Product failure
3. Ticket or purchase invoice (digitized)
4. Your address with CP, telephone and full Name.

Available in the establishment where the product was purchased and/or in our central offices:

Returns

• In the case of product return, it will only be the place of purchase by the end customer.
• Subject to the return policies established by the same seller.

CONTACT

• Importadora Global Rida S.A. de C.V.
• Matilde Márquez No. 68
• Colonia Peñón de los Baños C.P. 15520
• Alcaldía Venustiano Carranza, CDMX
• RFC: IGR1510164C2
• www.voragolive.com.
• Vorago, S.A. de C.V.
• Francisco Villa No. 3
• Col. San Agustín, C.P. 45645
• Tlajomulco de Zúñiga,
• Jalisco, México.
• Tel. (33) 3044 6666

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>