POWER SOLID PS-PLU600VA#1B7KR Line Interactive UPS User Manual

POWER SOLID PS-PLU600VA#1B7KR Line Interactive UPS

SAFETY-WARNING

• The voltages inside UPS may be hazardous. Do not attempt to disassemble the unit. The unit contains no user-serviceable parts.

  • Only factory service personnel may perform repairs.
  • The internal battery voltage is 12Vdc. Sealed, lead-acid, 6-cell battery.
  • Connection to any other type of receptacle other than a two-pole, three-wire grounded receptacle may result in shock hazards as well as a violation to local electrical codes.
  • In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.
  • Do not allow liquids or any external objects to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit.
  • This unit is designed for installation in a controlled environment (temperature-controlled, indoor area free of conductive contaminants). Avoid installing the UPS in locations where there is static or flowing water, or excessive humidity.
  • Do not plug the UPS input into its own output.
  • Do not attach a power strip or surge suppressor to the UPS.
  • Do not connect non-computer-related items, such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to UPS.
  • To reduce the risk of overheating the UPS, do not cover the UPS cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat-emitting appliances such as air heaters or furnaces.
  • Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
  • Do not dispose the batteries into fire as they may explode.
  • Do not open or mutilate the battery or batteries. Released electrolytes is harmful to the skin and eyes. It may be toxic.
  • A battery can present a risk of electrical shock and high short circuit current. The following precautions should be observed when working on batteries:
    • 1 ) Remove watches, rings, or other metal objects from the hands.
    • 2) Use tools with insulated handles.
    • 3) Wear rubber gloves and boots.
    • 4 ) Do not lay tools or metal parts on top of batteries.
    • 5) Disconnect the charging source prior to connecting or disconnecting battery terminals.
  • Servicing of batteries should be performed or supervised by technical and authorized personnel only.
  • When replacing batteries, replace with the same number and type of sealed lead-acid battery. The maximum ambient temperature rating is 40’C
  • the sum of the leakage currents of the UPS and the connected loads does not exceed 3.5 mA.
  • Beware of the possibility of electric shock when disconnecting of this unit from the mains, hazardous voltage still may be accessible through the supply from the battery. The battery supply should be therefore disconnected from the plus and minus terminals of the battery when maintenance or service work inside the UPS is necessary.

INTRODUCTION

This UPS is specially designed for Personal Computer with multi-functions. Its lightweight, compact design perfectly fits to the limited working environment. The line of UPS is equipped with boost and buckAVR to stabilize the input voltage range. It is also built with
DC start function. This function enables the UPS to be started up without AC power supplied. Although it’s a small UPS, The main features of UPS are listed below:

• Microprocessor control guarantees high reliability.
• Equipped with Boost and Buck AVR.
• Green Power Function for energy saving.
• DC Start Function.
• Auto restart while AC recovery.
• Compact size, Light Weight.
• Provides AC Overload protection.

TROUBLESHOOTING

SYSTEM DESCRIPTION Front panel

1. Power Switch
2. LED Indicators-

• AC Mode: Green LED lighting
• Battery Mode: Yellow LED Flashing
• Fault Mode : Red LED Lighting

Back Panel:

1. AC input
2. Output receptacles
3. USB & RJ11 (optional)
4. USB & RS232(optional)
5. Circuit breaker

Inspection

Remove the UPS from its packaging and inspect it for damage that may have occurred during shipping. If any damage is discovered, repack the unit and return it to the place of purchase.

Charging

This unit is shipped from the factory with its internal battery fully charged, however, some charge may be lost during shipping and the battery should be recharged prior to use. Turn on the UPS, Plug the unit into an appropriate power supply and allow the UPS  to charge fully by leaving it plugged in for at least 6 I hours with no load (no electrical devices such as ? computers, monitors, etc.) connected.

Placement

Install the UPS unit in any protected environment that provides adequate airflow around the unit, and is free from excessive dust, corrosive fumes and conductive contaminants. Do not operate your UPS in an environment where the ambient temperature or humidity is high.

On the other hand, place the UPS away from the monitor at least 20cm to avoid interference.

Connection

Plug the UPS into a 2-pole, 3-wire grounded receptacle. Then connect one computer-related device into each of the power receptacles supplied on the back of the UPS.

Turn On/Off

To turn on the UPS unit, press the power switch lightly. To turn off the UPS unit, press the power switch again

DC Start

All Series are equipped with DC Start. To start the UPS when AC utility power is not available, simply press the power switch.

SPECIFICATION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>