LEDVANCE 78135 Level 2 Commercial Charger Pedestal Instruction Manual

LEDVANCE 78135 Level 2 Commercial Charger Pedestal

Product Specifications

• Product Name: LEDVANCE PHASE EV
• Model: EVCPED
• Item No: 78135
• Type: Level 2 Commercial Charger Pedestal
• Compatibility: For use with EVC48ALVL2C1XX (Level 2 Commercial EVSE)

Product Usage Instructions

Safety Precautions

Upon receipt of the pedestal, inspect for any freight damage.
Only licensed electricians should provide installation services.
Disconnect power before installation. Install in accordance with electrical codes and safety standards.

Tools You Will Need

• 1/4 in hex bit driver
• Phillips screwdriver (#2)
• Wire cutter & stripper
• Crimping pliers
• Hammer drill
• Level
• Eyes & ear protection

Pedestal Installation

1. Use the leveling plate as a template to mark 4 holes on the concrete foundation.
2. Drill 4 holes using a 15/32 (12mm dia.) hammer drill bit.
3. Hammer the M12*120mm expansion anchor bolts in place.
4. Place the leveling plate over the anchor bolts, followed by the pedestal. Feed conduit and wirings through the bottom of the pedestal.
5. Attach the pedestal to the anchor bolts using washers, lock washers, and nuts. Level the pedestal base and tighten the anchor nuts.
6. Insert pedestal base cover over the base and tighten with M4*10mm screws.

Installing the Mounting Plate to a Pedestal

1. Use three (3) M5*12mm screws to attach the mounting plate to the pedestal.

Preparing the Charger

1. Remove the cover frame from the front of the charger by unscrewing screws.
2. Lift the cover outward and up to detach the cover frame.
3. Remove screws to take off the access panel cover.

Frequently Asked Questions (FAQ)

Q: Can I install this pedestal without professional help?
A: No, only licensed electricians should provide installation services to prevent personal injury or product damage.

Q: What are the tools required for installation?
A: Tools needed include a hex bit driver, Phillips screwdriver,wire cutter & stripper, crimping pliers, hammer drill, level, eyes & ear protection.

LEDVANCE PHASE EV
Installation Guide
Level 2 Commercial Charger Pedestal
Item No: 78135
Model: EVCPED
Base pedestal for use with EVC48ALVL2C1XX (Level
2 Commercial EVSE).

WARNING

Please Read All Instructions Before Attempting Installation

• TO PREVENT PERSONAL INJURY OR PRODUCT DAMAGE ONLY LICENSED ELECTRICIANS SHOULD PROVIDE ALL INSTALLATION SERVICES.
• TO AVOID ELECTRIC SHOCK OR COMPONENT DAMAGE DISCONNECT POWER BEFORE ATTEMPTING INSTALLATION OR SERVICING.
• THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC) AND ALL APPLICABLE FEDERAL, STATE AND LOCAL ELECTRICAL CODES AND SAFETY STANDARDS.
• ANY ALTERATION OR MODIFICATION OF THIS PRODUCT IS EXPRESSLY FORBIDDEN AS IT MAY CAUSE SERIOUS PERSONAL INJURY, DEATH, PROPERTY DAMAGE AND/OR PRODUCT MALFUNCTION.
• TO PREVENT PRODUCT MALFUNCTION AND / OR ELECTRICAL SHOCK THIS PRODUCT MUST BE PROPERLY GROUNDED.

Safety Precautions

IMPORTANT:
READ CAREFULLY BEFORE INSTALLING THE PEDESTAL. RETAIN FOR FUTURE REFERENCE.

GENERAL:
Upon receipt of the pedestal, thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier.

What’s Included

Tools You Will Need

• 1/4 in hex bit driver
• Phillips screwdriver (#2)
• Wire cutter & stripper
• Crimping pliers
• Hammer drill
• Level
• Eyes & ear protection

Pedestal Installation

1. Use the leveling plate as a template and mark the 4 holes on the concrete foundation. Make sure the power feed conduit is in the center as shown in the illustration below. Drill 4 holes using a 15/32” (12mm dia.) hammer drill bit to a minimum depth of 3-11/16” (93.6625mm). Hammer the M12*120mm expansion anchor bolts in place.

2. Next, place the leveling plate directly over the anchor bolts, followed by the pedestal. Make sure to feed the conduit and wirings up through the bottom of the pedestal and guide it out through the wiring access panel opening.

3. Use the included flat washers, lock washers, and nuts to attach the pedestal to the anchor bolts.
   Loosely install the anchor nuts until the pedestal is level.
   Level the pedestal base by adjusting the leveling screws and the anchor nuts.
   Tighten the anchor nuts to secure the pedestal in its final position.

4. Insert pedestal base cover over the base and tighten with the (2) M4*10mm screws.

Installing the Mounting Plate to a Pedestal

1. Remove the 2 screws – one on each side of the charger to detach the mounting plate from the charger.
2. Use the included three (3) M5*12mm screws to attach the mounting plate to the pedestal.

Preparing the Charger

1. Remove the cover frame from the front of the charger by unscrewing the 2 screws on top and 1 screw from the bottom of the charger.
2. Once the 3 screws are removed, carefully lift the cover outward and up to detach the cover frame.
3. Remove the 6 screws to take off the access panel cover.

For Rear Wiring
Remove the rear plug(s) by loosening the hex nut in a counterclockwise direction. Then use the same plug to cover the hole at the bottom of the charger. Use the included cable strain relief to run the wiring to the charger.

For Bottom Wiring
Use the included cable strain relief to run your wiring up from the bottom of the charger.

Mounting the Charger

1. Align the charger to the mounting plate and hang it as shown in the illustration below. Next, secure the charger to the mounting plate with the 2 original screws.
   Strain relief must be installed for IP rating.

2. For rear wiring installation, use the included cable strain relief and feed the power supply wires through the rear port with enough length to connect the wires to the terminals. Then attach the wiring panel cover to the pedestal with the included screws.

3. Attach the holster and cable hanger to the pedestal as shown in the illustrations below.

4. Use the included rubber plugs to cover any unused holes.

Tip: It’s easier to insert the plug by twisting it clockwise like you are hand tightening a screw.

Imported by
LEDVANCE
1100 Tyrone Pike
Versailles, KY 40383

• 1-800-LIGHTBULB (1-800-544-4828)
  www.ledvanceUS.com (US & Canada)
  LEDVANCE is a registered trademark.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>