TRIPP LITE SMART750RM1UN SmartPro 120V 750VA 600W Line Interactive Sine Wave UPS Owner’s Manual

TRIPP LITE SMART750RM1UN SmartPro 120V 750VA 600W Line Interactive Sine

Wave UPS

Specifications

• Model Number: SMART750RM1UN
• UPS Type: Line-Interactive
• Input Phase: Single-Phase
• Rated Input Current (Maximum Load): 7A
• Nominal Input Voltage(s) Supported: 120V AC
• Input Connection Type: 5-15P
• Input Circuit Breakers: 15A
• Recommended Electrical Service: 15A 120V
• Input Cord Length (ft.): 10
• Output Capacity (VA): 750
• Output Capacity (kVA): 0.75
• Output Capacity (Watts): 600
• Output Capacity (kW): 0.6
• Power Factor: 0.8
• Nominal Voltage Details: 120V nominal output in battery mode
• Frequency Compatibility: 60 Hz

Product Usage Instructions

Installation

1. Mount the UPS using the included brackets for rack or vertical installation.
2. Connect the UPS to a power source using the provided input cord.
3. Connect your devices to the output receptacles on the UPS.

Operation

1. Ensure the UPS is turned on using the power button.
2. Monitor the front panel status LEDs for information on power status.
3. Use the network interfaces for remote access and power monitoring.

Battery Replacement
If you need to replace the UPS battery, follow these steps:

1. Access the internal UPS replacement battery cartridge.
2. Replace the battery with a compatible one as per the provided instructions.

FAQ

• Q: What is the runtime at full load for this UPS?
  A: The runtime at full load is dependent on various factors such as battery type and load, but typically it is specified in the user manual.

• Q: Can I expand the runtime of this UPS?
  A: Yes, you can expand the runtime by adding external battery packs if supported by the UPS model.

SmartPro 120V 750VA 600W Line-Interactive Sine Wave UPS, 1U Rack/Vertical, Pre-installed WEBCARDLX Network Interface, USB, DB9 Serial
M ODEL NUMBER: SMART750RM1UN

Highlights

• 75kVA / 750VA / 600W line interactive 1U rack/vertical UPS, Sine wave output
• 120V output, Corrects brownouts and overvoltages from 83V to 147V
• 0.8 Power Factor, Front panel status LEDs
• Mounting brackets support 2 and 4 post installation
• 98% line-mode efficiency, 2 switched load banks
• USB, RS232, EPO and Pre-installed WEBCARDLX Network Interface
• 120V NEMA 5-15P input, 6 NEMA 5-15R outlets
• To enable the Auto Probe feature, this product requires LX firmware update 15.5.2 or later to be installed

Package Includes

• SMART750RM1U with Pre-installed WEBCARDLX network interface
• Mounting hardware
• USB, DB9 and EPO Cabling
• Instruction manual

Description
SMART750RM1U 750VA/.75kVA/600W line-interactive sine wave UPS system offers complete power protection for critical network applications in a highly efficient 1U total rack/vertical configuration. Network management interfaces support communications via USB port, DB9 serial port and pre-installed WEBCARDLX network management interface card. The Java-free HTML5-based WEBCARDLX interface enables full remote access for site power and UPS status monitoring, configuration, control and email notifications via secure web browser, SNMP, telnet or SSH. It supports 10/100 Mbps auto-sensing for optimum communication with an Ethernet network. Optional EnviroSense2 modules (sold separately) provide a variety of environmental monitoring capabilities. Protocols supported include HTTP, HTTPS, SMTP, SNMPv1, SNMPv2, SNMPv3, telnet, SSH, FTP, DHCP and NTP. Line-interactive voltage regulation, network-grade surge suppression and long-lasting sine wave AC output during blackouts make this UPS ideal for advanced networking applications in data centers, computer rooms and network closets.

Features

• SMART750RM1U .75kVA / 750VA / 600 watt line interactive UPS
• 1U rack/vertical compatible form factor
• Included mounting brackets support 2 and 4-post rack-mount installation; Optional 4POSTRAILKIT1U is available for additional support
• NEMA 5-15P input; 6 5-15R output receptacles
• Installed depth of only 16.75 in. / 42.5cm
• Sine wave output in both AC and battery backup modes
• Line Interactive UPS provides Automatic Voltage Regulation / AVR to maintain 120V nominal output during brownouts to 83V and overvoltages to 147V without using battery power
• Full load efficiency rating of 98% saves energy and ensures cool operating temperatures
• Integrated 2 bank switched PDU enables remote outlet management for load shedding or remote reboot of individual devices
• Network interfaces support communications via built-in USB, DB9 serial / contact-closure and pre-installed WEBCARDLX network management card
• WEBCARDLX interface allows full remote access for power monitoring, configuration, control and email notifications via secure web browser, SNMP, Telnet, SSH or Command Line
• Reduce Service Calls with Auto Probe Autonomous Device Management. The Auto Probe feature (Firmware 15.5.2 and greater) checks the connectivity status of any networked device and automatically takes one or more user-configured actions if the device fails to respond; actions include outlet reboot, set SNMP traps, SNMP OID sets, and even script execution when used in conjunction with the PowerAlert Network Shutdown Agent (PANSA)
• Optional E2 sensors enable site monitoring of temperature, humidity and contact-closure status HID-compliant USB interface enables integration with built-in power management and auto shutdown features of Windows and macOS
• Intelligent battery management system extends battery life
• 3 stage metered LEDs offer current monitoring and battery charge level
• Mains power and voltage regulation LEDs offer at-a-glance power status information
• Front panel switches support self-test and alarm cancel functions
• Field replaceable, hot-swappable internal UPS batteries

Specifications

**OVERVIEW**

UPC Code| 037332190734
UPS Type| Line-Interactive
**INPUT
Input Phase| Single-Phase
Rated input current (Maximum Load)| 7A
Nominal Input Voltage(s) Supported| 120V AC
UPS Input Connection Type| 5-15P
Input Circuit Breakers| 15A
Recommended Electrical Service| 15A 120V
Input Cord Length (ft.)| 10
Input Cord Length (m)| 3.05
****OUTPUT
Output Capacity (VA)| 750
Output Capacity (kVA)| 0.75
Output Capacity (Watts)| 600
Output Capacity (kW)| 0.6
Power Factor| 0.8
Nominal Voltage Details| 120v nominal output in battery mode
Frequency Compatibility| 60 Hz
Output Voltage Regulation (Line Mode)| ** -21%, +8%
Output Voltage Regulation (Battery Mode)| +/- 5%
Load Management Receptacles| Two switchable single-outlet 5-15R load banks
---|---
Output AC Waveform (AC Mode)| Sine wave
Output AC Waveform (Battery Mode)|

Pure Sine wave

Nominal Output Voltage(s) Supported| ****

110V; 115V; 120V

Output Receptacles| (6) 5-15R
Individually Controllable Load Banks| Yes
**BATTERY
Battery Type| Valve Regulated Lead Acid (VRLA)
Runtime Full Load (min.)| 4.9 min. (600W)
Runtime Half Load (min.)| 13.2 min. (300W)
Expandable Runtime| No
DC System Voltage (VDC)| 24
Battery Recharge Rate (Included Batteries)| ** 3.6 hours maximum from 10% to 90% (typical, full load discharge)
Battery Access| Front panel battery access door
Internal UPS Replacement Battery Cartridge|  <a class=”productLink” href=”//tripplite.eaton.com/1U-UPS-Replacement-24VDC-Battery- Cartridge-1-Set-4- for-Select-Tripp-Lite-SmartPro- UPS~RBC64-1U”>RBC64-1U 
Battery Replacement Description| Hot-swappable, user replaceable batteries
**VOLTAGE REGULATION
Voltage Regulation Description| Automatic voltage regulation (AVR) maintains line power operation with an input voltage range of 83 to 147
Overvoltage Correction| Input voltages between 128 and 147 are reduced by 12%
Undervoltage Correction| Input voltages between 83 and 107 are boosted by 14%
****USER INTERFACE, ALERTS & CONTROLS
Switches| 2 Switches control off/on power status and alarm-cancel/self-test operation. LX Platform Interface: Recessed reset switch for interface reboot and factory reset
Alarm Cancel Operation| Power-fail alarm can be silenced using alarm-cancel switch; once silenced, alarm will re-sound to indicate low- battery status
Audible Alarm| Audible alarm indicates power-failure, overload and low-battery conditions
LED Indicators| 5 LEDs indicate line power, battery power, overload, voltage regulation and battery low/replace status. Network Link/Activity (Green): Flashes for network activity. Network Speed (Yellow): 10 Mbps (Flashing), 100 Mbps (On steady). LX Platform Interface Status: Normal Operation (Solid Green); Software Update (Alternating Green/Orange ~1/sec); Factory Reset (Alternating Green/Orange ~2/sec).
****SURGE / NOISE SUPPRESSION
UPS AC Suppression Joule Rating| 450
UPS AC Suppression Response Time| ** Instantaneous
EMI / RFI AC Noise Suppression| Yes
**PHYSICAL**

Primary Form Factor| Rackmount; Vertical
Rack Height| 1U
Cooling Method| Fan
Included Mounting Accessory Description| Included mounting brackets provide front-rail installation in 2 or 4 post racks; For additional stability in 4 post racks, consider optional 4 post mounting accessories 4POSTRAILKIT1U & 4POSTRAILKITWM
Installation Form Factors Supported with Included Accessories| 2 post 19 inch rackmount; 2 post front mount; 4 post 19 inch rackmount
Installation Form Factors Supported with Optional Accessories| 4 post rackmount full-depth ( <a class=”productLink” href=”//tripplite.eaton.com/4-Post-1U-Universal- Adjustable-Rack-Mount-Shelf- Kit~4POSTRAILKIT1U”>4POSTRAILKIT1U ); 4 post rackmount short- depth ( <a class=”productLink” href=”//tripplite.eaton.com/4-Post-1U-Universal- Adjustable-Rack-Mount-Shelf- Kit-for-Wall-Mount- Racks~4POSTRAILKITWM”>4POSTRAILKITWM ); Vertical Mount Enclosures ( <a class=”productLink” href=”//tripplite.eaton.com/SmartRack-5U-Low- Profile-Vertical-Mount-Server-Depth- Wall-Mount-Rack-Enclosure- Cabinet~SRWF5U36″>SRWF5U36 ,  <a class=”productLink” href=”//tripplite.eaton.com/SmartRack-5U-Low-Profile-Vertical-Mount-Switch- Depth-Wall-Mount-Rack-Enclosure- Cabinet~SRWF5U”>SRWF5U ,  <a class=”productLink” href=”//tripplite.eaton.com/SmartRack-5U- Low-Profile- Vertical-Mount-Switch-Depth-Wall-Mount-Structured-Wiring-Enclosure-Adjustable- Equipment- Brackets~SRWF10UMOD”>SRWF10UMOD )
Minimum Required Rack Depth (cm)| 50.80
Minimum Required Rack Depth (inches)| 20
Optional Mounting Accessory Notes| Optional  <a class=”productLink” href=”//tripplite.eaton.com/4-Post-1U-Universal-Adjustable-Rack-Mount- Shelf- Kit-for-Wall-Mount-Racks~4POSTRAILKITWM”>4POSTRAILKITWM  enables installation in 4-port short-depth racks from 14.5 to 23.5 inches (368 to 597mm); Optional  <a class=”productLink” href=”//tripplite.eaton.com/4 -Post-1U-Universal-Adjustable-Rack-Mount-Shelf- Kit~4POSTRAILKIT1U”>4POSTRAILKIT1U  enables installation in 4-post full-depth racks from 20.5 to 36 inches (521 to 914mm)
Primary UPS Depth (mm)| 425
Primary UPS Height (mm)| 44
Primary UPS Width (mm)| 445
Shipping Dimensions (hwd / in.)| 5.30 x 21.20 x 22.40
Shipping Dimensions (hwd / cm)| 13.46 x 53.85 x 56.90
Shipping Weight (lbs.)| 34.30
Shipping Weight (kg)| 15.56
UPS Housing Material| Steel
UPS Power Module Dimensions (hwd, cm)| 4.44 x 44.45 x 42.54
UPS Power Module Dimensions (hwd, in.)| 1.75 x 17.5 x 16.75
UPS Power Module Weight (kg)| 13.61
UPS Power Module Weight (lbs.)| 30
Unit Weight (lbs.)| 30.0000
Unit Weight (kg)| 13.61
**ENVIRONMENTAL
Operating Temperature Range| 32° to 104°F (0° to 40°C)
Storage Temperature Range| 5° to 122°F (-15° to 50°C)
---|---
Relative Humidity| 0 to 95%, non-condensing
AC Mode BTU / Hr. (Full Load)| 38
AC Mode Efficiency Rating (100% Load)| ** 98%
Battery Mode Heat Dissipation (BTU/Hr) @ Full Load| 545
Audible Noise| 45 dBA maximum, front side 1m
**COMMUNICATIONS
Network Management Cards|  <a class=”product link” href=”//tripplite.eaton.com/Network-Card-Eaton-Tripp-Lite-Series-UPS- Systems~WEBCARDLXE”>WEBCARDLXE 
Network Monitoring Port Description| Includes pre-installed WEBCARDLX Network Management Card
PowerAlert Software| For local monitoring via the UPS’s built-in communication ports, download PowerAlert software at https://tripplite.eaton.com/products /power-alert
Communications Cable| USB and DB9 cabling included
WatchDog Compatibility| Supports Watchdog application, OS and hard-reboot restart options for remote applications
EPO Port| RJ11 interface jack with 4-meter cable included. Supports normally open and normally closed EPO systems
SNMP Compatibility| SNMP V1, V2c, V3
Network UPS Tools (NUT) Compatibility| NUT compatible. See a full list of NUT compatible Tripp Lite UPS systems at https://networkupstools.org/stable- hcl.html?manufacturer=Tripp%20Lite
Network Compatibility| 100 Mbps (Fast Ethernet)
Network Management Card Description| ** Network management card included
Communications Interface| DB9 Serial; EPO (emergency power off); Pre-installed network card; Slot for SNMP/Web interface; USB
**LINE / BATTERY TRANSFER
Transfer Time| 5 milliseconds AC to DC; 1 millisecond DC to AC
Low Voltage Transfer to Battery Power (Setpoint)| ** 83
High Voltage Transfer to Battery Power (Setpoint)| 147
**FEATURES & SPECIFICATIONS
Cold Start (Startup in Battery Mode During a Power Failure)| ** Cold-start operation supported
High Availability UPS Features| Auto Probe Monitoring and Reboot (included); Automatic Voltage Regulation (AVR); Hot swappable batteries; Remote management; Surge/noise protection
Grounding Details| Back panel grounding lug
**APPLICATIONS
UPS Applications| Large Network; High-End Desktop/Small Network; Retail/Point of Sale; Hospitality
****STANDARDS & COMPLIANCE**

Product Certifications| CSA (Canada); NOM (Mexico); UL 1778
Product Compliance| RoHS; FCC Part 15 Class A (USA)
**WARRANTY & SUPPORT**
Product Warranty Period (Worldwide)| 2-year warranty, 3 year with registration. Note: <a class=”insuranceLink” href=”//tripplite.eaton.com/support/product-warranty- registration”>Registration is required for 3-year warranty.
Connected Equipment Insurance (U.S., Canada & Puerto Rico)| $250,000 <a class=”insuranceLink” href=”//tripplite.eaton.com/support/insurance- policy”>Ultimate Lifetime Insurance 

1000 Eaton Boulevard Cleveland, OH 44122 United States
https://tripplite.eaton.com
© 2024 Eaton. All Rights Reserved.
Downloaded from Arrow.com.
Eaton is a registered trademark. All other trademarks are the property of their respective owners.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>