ECG EFT 11423 WE Freezer Instruction Manual

: June 3, 2024
: ECG

ECG EFT 11423 WE Freezer Instruction Manual

SAFETY INSTRUCTIONS

Read carefully and save for future use!

Warning: The safety measures and instructions, contained in this manual, do not include all conditions and situations possible. The user must understand that common sense, caution and care are factors that cannot be integrated into any product. Therefore, these factors shall be **** ensured by the user/s using and operating this appliance. We are not liable for damage caused during transportation, improper use, voltage fluctuation or any change or modification of any part of the appliance. To protect against a risk of fire or electric shock, basic precautions shall be taken while using electrical appliances, including the following:

Make sure the voltage in your outlet corresponds to the voltage provided on the appliance label and that the socket is properly The outlet must be installed in accordance with applicable electrical codes according to EN.
Do not operate the device if the cord is damaged. All repairs or adjustments including cord replacements shall be performed by a professional service centre! Do not remove the protective covers from the appliance; there is a risk of electric shock!
Protect the appliance against direct contact with water and other liquids, to prevent potential electric Do not immerse cord or plug in water!
Do not use the appliance in humid environments or in areas where there may be gas leakage or contact with an explosive Do not touch the cord or the device with wet hands. Risk of electric shock.
The power cord must remain accessible once the device is Do not shorten the cable and do not use splitters in electric outlets. Do not allow the cord to touch hot surfaces or place the cord over sharp edges.
Do not switch the appliance on or off by plugging in or pulling out the power supply Do not remove the power cord from the outlet by yanking the cord. Unplug the power cord from the outlet by grasping the plug.
Do not insert any objects into the device or place any objects on the device (e.g. vases, cups, ). Never cover the ventilation openings!
Do not use other electrical appliances or freezing equipment in the
If this appliance is replacing an old appliance with a lock, make the

lock of the old appliance inoperational to prevent children from
locking themselves inside (e.g. when playing).

Do not use mechanical devices or other artificial means to speed up Do not use electrical appliances in the food storage area. Protect the cooling circuit of the appliance against damage.
Do not allow children to play with the Also, they may not sit on the shelves and hang on the door of the appliance.
Do not use sharp metal objects to remove ice in the refrigerator, as they can damage the freezing circuits and cause irreparable damage to the If necessary, use a plastic scraper.
Do not store explosive materials such as sprays with propellant in the
Do not place containers (glass bottles or cans) with liquids in the The container could burst.
Bottles containing liquids with high alcohol content must be properly closed and placed vertically when
Do not expose the appliance to direct sunlight, do not use it outside and do not expose it to
Do not touch the cooling surfaces with wet Risk of injury.
Do not consume the ice removed from the
This appliance is designed for domestic use and for use in similar places, such as:
- Kitchenettes in shops, offices and other workplaces
- appliances used by guests in hotels, motels and other residential
- appliances used in bed and breakfast residences
This appliance may be used by children under 8 years of age and older and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if supervised or instructed to use the appliance in a safe manner and understand the potential Children shall not play with the appliance. User cleaning and maintenance must not be performed by unsupervised children.

21. Children aged 3 to 8 years can insert and remove food from

refrigerating appliances.

Child supervision is essential to prevent them from playing with the
The manufacturer is not liable for any damage caused by improper grounding/use.
It is necessary to keep free the ventilation openings in the cover or in the construction of the

To prevent food contamination, please follow these recommendations:

Opening the door for a long time can cause a significant increase in the temperature inside the
Regularly clean surfaces and accessible drainage systems that may come into contact with
Clean water containers if not used for 48 h; flush the water system connected to the water supply if the water has not flowed for 5
Store raw meat and fish in the refrigerator in suitable containers so that they do not come into contact with or drip into other
Two-star freezing compartments are suitable for storing pre- frozen food, storing or making ice cream and making ice
One-, two- and three-star compartments are not suitable for freezing fresh
If the refrigerating appliance is left empty for a long time, turn it off, defrost, clean, dry and leave the door open to prevent mold formation inside the appliance.

WARNING: RISK OF FIRE/FLAMMABLE

MATERIALS

This appliance contains R600a (isobutane coolant), natural (natural) gas that is very environmentally friendly but flammable. When transporting and installing the appliance it is necessary to ensure that none of the parts of the cooling circuit is damaged. In case of damage limit the flame and ventilate for several minutes the space where the appliance is located.
The cooling system contains high-pressure coolant. Do not manipulate the system. It must only be repaired by a qualified person.
When replacing the interior lighting of the refrigerator, always unplug the refrigerator – otherwise there is a risk of electric shock. • If the replacement of the interior lighting is too complicated for you, contact your service representative. • If the products are equipped with LEDs, do not remove the lighting cover and LED yourself. – contact your service representatives.

REPLACING THE LED BULB: Do not remove the indicator cover or indicator yourself when the internal or external LEDs no longer operate. Contact the service representatives.

INTRODUCTION

Dear customers!
Thank you for purchasing this freezer. Please read carefully 2 the instructions in this manual to obtain the best and longest performance from this product.

DESCRIPTION

This appliance is not intended for use as a built-in appliance.
This description is only for information on the components of the 3 appliance. Individual parts may differ according to the particular appliance model.

Compartment (for pizza)
Temperature control
Drawers for storing frozen foods
Adjustable feet

FREEZER INSTALLATION 4

Unpacking the freezer

Remove all tapes and labels (except the rating plate) from the freezer before use. You can easily remove the remnants of tapes and glue using a sponge and a small amount of Clean it after with warm water and dry it.
Do not use any sharp objects, alcohol, flammable or abrasive cleaners, which could damage the surface finish of the
When transporting the appliance, do not tilt it more than 45° from the vertical position.

Warning: A minimum of two people are required to transport the freezer. Do not attempt to move the freezer yourself, as it may cause you a back or other injury. Levelling the appliance

If the freezer is not seated straight, the door may not be properly closed or sealed, which may cause problems with cooling performance, moisture penetration and For trouble-free operation, it is very important to level the freezer properly.
Use the adjusting feet to level the Rotate the adjusting foot clockwise to raise the respective side, rotate couterclockwise to lower it.

Note: Ask a second person to tilt the freezer backwards to ease the setting of the foot. Perform this operation before placing the food in the freezer.

Location and space requirements

Place the freezer so that it is not exposed to direct
The freezer should be installed at least 50 cm away from a stove, gas oven or heating furnace and at least 5 cm away from an electric If the freezer is located near a cabinet freezer, a gap of at least 2 cm should be between the appliances to avoid condensation of moisture on the outside.
Do not place any objects on the freezer and install it at a convenient location so that there is at least 10 cm of free space on the sides and behind the appliance and at least 30 cm of free space above the
If you install the freezer close to a solid wall, leave enough space on the hinge side to allow the door to open easily (width (W) × depth (D)> 902 × 1052 mm), see

The ambient temperature influences the energy consumption and proper functioning. When placing the appliance, do not forget that it is advisable that the appliance operates in the temperature range specified Climate classes and their description: see information sheet
T (tropical): This refrigerator is intended for use at ambient temperatures between 16 °C and 43 °C.
ST (subtropical): This refrigerator is intended for use at ambient temperatures between 16 °C and 38 °C.
N (normal): This refrigerator is intended for use at ambient temperatures between 16 °C and 32 °C.
SN (subnormal): This refrigerator is intended for use at ambient temperatures between 10 °C and 32 °C.

Warning:

Prevent contact of the freezer with flammable materials and vapours, e.g. gasoline. Otherwise there is a risk of explosion, fire, burns or other serious injury.

Before first use

Remove all packaging material and thoroughly clean the interior of the freezer with a solution water and soda before first use, then rinse with clean water and
Prior to first use or after relocation, let the freezer stand for 3 hours in vertical position before plugging it into the power Otherwise, you could damage the compressor.
You may detect a slight odour when you first switch it This odour will disappear once the appliance starts to cool.

Connection

Before plugging it in the outlet make sure that the voltage on the nameplate corresponds with the voltage in your
The outlet must be accessible after installing the
We recommend that freezer connects to a separate circuit, which does not power any other Use an electrical outlet, which cannot be accidentally disconnected by an e.g. switch.
Do not use extension cables to connect the

Note: Disconnect the freezer from the power supply before any manipulation. After finishing the installation plug the freezer in the outlet and set the thermostat to the required value.

Switching on the appliance

When you first turn the appliance on, it should run continuously for 24 hours before it reaches a sufficiently low
Avoid frequent opening of door during that time and putting in large amount of
If the appliance is turned off or disconnected from the power supply you need to wait at least 5 minutes before restarting or plugging it in to prevent damage to the

Reversing the door opening

Reversing the door opening direction can be done by a qualified service center.
When changing the direction of opening the door, we recommend to ask another person for assistance. You will need an adhesive tape, cross and flat screwdriver for assembly.
The freezer must be disconnected from power and empty before handling! Warning:

When removing the door, the appliance should be tilted backwards. You should support the appliance under the top panel with a solid
Do not tilt the freezer by more than 45° from the Avoid laying the freezer flat completely, since this could damage the cooling system!

Secure the door with adhesive tape.
Remove the left opening cover of the upper hinge, the upper hinge cover (on the right) and unscrew the upper hinge bolts, then remove the upper hinge. Hold the door in vertical position all the time and make sure it does not fall
Remove the door
Remove the plug on the underside of the door and place it on the other side.
Remove the lower hinge and an adjustable
Install the lower hinge on the left side of the freezer and the adjustable leg on the
Install the door on the lower hinge and check that the seal is sealing properly and that the door position is correct. Install the left upper hinge and attach the cover to the hinge (supplied as an accessory). Finally, attach the cover to the holes for the right upper hinge.

OPERATING INSTRUCTIONS

Temperature control

The thermostat controller is located inside the freezer behind the front door. The thermostat regulates the temperature of the interior automatically. Thermostat settings:

Setting „Min“: Lower cooling power, higher
Setting „Mid“: Regular operation, suitable in most cases.
Setting „Max“: Maximum cooling power, lowest

Notes:

At high ambient temperatures, for example during a hot summer day, it may be necessary to set the thermostat to “Max”. In this case, the compressor can run continuously to provide the required lowtemperature inside the freezer.
When switching on the first time after installing the freezer, set the thermostat to a medium value and allow the freezer interior space to cool well before inserting the We recommend to wait 24 hours before inserting the food.

Tips for storing food in a freezer

When storing frozen food, follow the instructions on food If there are no instructions given, the food should not be stored for more than 3 months from date of purchase.
When buying frozen food, make sure that it was frozen at sufficient temperature and that the packaging is not
Frozen foods should be transported in a suitable packaging and placed in the freezer as soon as
If the frozen food packaging shows signs of moisture or swelling, the food was probably stored at improper temperatures and its quality is
The storage life of frozen foods depends on the room temperature, thermostat setting, the frequency of door opening, type of food and the time needed to transport food from the store in the Never exceed the indicated maximum storage life.
Make sure that the foods do not damage the freezer pipes when closing the

Freezing fresh foods

Make sure that the freezing procedure is carried out in the strictest hygienic conditions, since the freezing alone does not sterilize the
Do not place hot or warm foods in the
It is advisable to store cooked meat and fish in places above raw meat and fish to prevent any transfer of
Leave space between the frozen food to allow the air to circulate inside the
Wrap the individual foods separately in plastic bags, foil or freezer bowls to avoid transfer of taste and the drying of
Do not place fresh food side by side with frozen food, it could lead to partial thawing of already frozen
When freezing fresh food (meat, fish, minced meat), it is recommended to divide the foods into individual portions and freeze them
The maximum freezing capacity in kg in 24 hours at room temperature 25 °C is specified in the section

„Technical specifications“ at the end of this manual. Never freeze more than the maximum allowable quantity of food.
Note: Never place beverages or foods in preserving jars in the freezer. For ensuring optimum performance, keep in the freezer enough space to allow air flow around individual packages.

CARE AND MAINTENANCE

Cleaning the freezer

Before cleaning the freezer, unplug the power cord from the
Do not clean the freezer with running water. Use a sponge or cloth dipped in a mild solution of warm water and Do not use aggressive or abrasive cleaners.
Wipe all surfaces carefully and dry them
Do not use on plastic and rubber parts cleaning waxes, concentrated detergents, bleach or cleaners containing
Do not use for cleaning plastic parts paper cleaning wipes, window cleaners, scouring powders or

flammable liquids that could scratch or otherwise damage the surface finish.

Wash the accessories of the freezer separately in mild detergent Do not wash in dishwasher.

**GB**

Regularly once a year, clean the condenser on the back of the freezer with a brush. You increase the efficiency of the appliance and save

Defrosting

After a while, a layer of ice forms inside the freezer, depending on the frequency and length of the door opening and room It is important to ensure that frost is does not form in places where it would prevent the proper sealing of the door. The leaky door could cause the outside air to penetrate into the freezer space and a decrease in cooling efficiency accompanied by continuous compressor operation.
A thin layer of frost can be removed with a plastic Do not use metal or sharp objects or mechanical devices or other means.
Remove all frost from the appliance
There is no need to shut down the appliance when removing the thin layer of
When removing a thick layer of ice, disconnect the appliance from the power supply and move all food to a cool The best time for defrosting is when the freezer is almost empty. The defrosting should be quick so that the temperature of the foods would not rise.
Do not use metal or sharp objects or mechanical and other devices to speed up the defrosting
The increase in temperature of frozen foods during defrosting of the freezer shortens their storage
One or more hot water containers can be placed in the freezer compartment to reduce the defrosting
After defrosting wash and wipe dry the freezer with a sponge or dry tea
Plug the appliance into the power supply and allow it to run at level 5 for 2–3 hours before inserting the
Before placing the foods back in the freezer check them You have to consume the partially defrosted foods within 24 hours or you have to cook them and freeze them again.

Long-term shutdown

If you do not intend to use the freezer for a longer period of time, proceed as follows:

Pull the plug out of the outlet to disconnect the freezer from the power
Clean and dry the interior of the freezer as described in the section „Cleaning of the freezer“.
Leave the freezer door open to prevent unpleasant odours forming in the unused.

Power saving tips

Place the appliance in a cool, well-ventilated location, away from direct sunlight and heat sources (radiators, cookers).
Allow the warm food cool before putting it in the
The food you want to thaw can be moved from the freezer to the refrigerator where it helps to keep the refrigerator temperature
Beverages and liquids must be in closed containers in order not to increase the moisture inside the
When putting in foods, limit the time you open the freezer door to a
Do not leave open covers of individual freezer
Keep the door seal Replace a damaged door seal.

GB TROUBLESHOOTING

You can solve a number of common problems on your own. If the freezer is not working properly, check the following points before calling a service technician:

The freezer does not work| The power cord is disconnected. The main house breaker is off.

The electrical outlet is not under voltage. Test the functionality of the outlet by plugging in another appliance.

---|---
The freezing in the freezer is insufficient| The freezer is overloaded.

Set the thermostat to higher value. The door does not close properly. There is dust on the condenser.

If the door has been opened for too long or too often, it will take some time for the freezer to reach the set temperature.

Check that the airflow is not restricted behind the freezer due to insufficient distance from the wall.

Odour| Aromatic foods should be well wrapped. Check for spoiled food.

Clean the inside of the appliance regularly.

Long continuous compressor operation.| During summer at high ambient temperatures, the compressor’s continuous operation is normal.

Do not put too much fresh food in the freezer at once. Allow the food to cool before placing it inside.

Reduce the door opening frequency.

The light inside the freezer is off.| Make sure that the freezer is plugged in and the bulb is not broken.
The freezer door can not be properly closed.| The door is blocked by improperly stored food. The freezer is overloaded.

Check that the freezer does not touch other appliances or kitchen furniture and stands level.

Noisy operation.| Check that the food is evenly spaced and the freezer is level. Check the correct placement of the freezer inside equipment.

USE AND DISPOSAL OF WASTE

Wrapping paper and corrugated paperboard – deliver to scrapyard. Packing foil, PE bags, plastic elements – throw into plastic recycling containers.

DISPOSAL OF PRODUCTS AT THE END OF LIFETIME

Disposal of electric and electronic equipment (valid in EU member countries and other European countries with an implemented recycling system)
The represented symbol on the product or package means the product shall not be treated as domestic waste. Hand over the product to the specified location for recycling electric and electronic equipment. Prevent negative impacts on human health and the environment by properly recycling your product. Recycling contributes to preserving natural resources. For more information on the recycling of this product, refer to your local authority, domestic waste processing organization or store, where you purchased the product.
This product complies with EU directives on electromagnetic compatibility and electrical safety. This product meets the requirements for heavy metals in electrical equipment.
The operating manual is available on internet at www.ecg- electro.eu. Changes of text and technical parameters reserved.
08/05 Old refrigerators and freezers contain insulating gases and freezing medium, which must be disposed of. Entrust the disposal to a competent local waste disposal service. If in doubt, contact your local authorities or your vendor. Make sure that the pipes of the cooling unit, which will be removed by the appropriate waste disposal,service are not damaged.

Contact for professional servicing of this product can be found in the enclosed Warranty Certificate or on the website ecg-electro.eu.
The warranty for this product is 24
Spare parts listed in EU 2019/2019 are available for 7
You can access the product database, where information about this product is stored according to EU 2019/2016, by reading the QR code on the energy.