Lydsto P1 MAX Robotic Pool Vacuum Cleaner with Wall Climbing User Manual

Lydsto P1 MAX Robotic Pool Vacuum Cleaner with Wall Climbing

Tips
Please read this manual carefully before using this product, and keep it properly.

Precautions

1. This appliance can be used by adults. If persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge they must be given supervision or instruction concerning the use of the appliance in a safe way and understanding the hazards involved. Cleaning and maintenance shall not be done by children without supervision. Read the manual carefully and use the cleaning robot according to the instructions, we are not responsible for any loss or injury caused by improper use.
2. The appliance is only to be used with the unit provided.
3. The power must be off before cleaning or maintaining the appliance.
4. In case of parts damage or consumable replacement, please ensure the following two aspects:➀Through the manufacturer’s regular channels to purchase parts;➁Qualified technical personnel operation maintenance replacement.
5. Before the robot starts working, the dust box must be installed, otherwise hard foreign objects sucked in will cause damage to the rotor blades.
6. At the same time, it must be confirmed that the cable should be completely relaxed to avoid entanglement with the host and affect the cleaning effect.
7. When charging, the battery charger must be connected to a socket with leakage protection and grounding, and placed in a cool place at least M away from the edge of the swimming pool.
8. Avoid placing or covering any objects to prevent damage to internal electrical components caused by overheating. Keep the adapter away from standing water.
9. When using, the operator must not touch the track and wheels to avoid damage. Do not use the cleaning robot when people or animals are in the pool. Do not use or store the cleaning robot near any heat source.
10. Do not pierce the shell of the robot with nails or other sharp objects, and do not knock, hit or throw the cleaning robot.

Caution

1. It is strictly forbidden to use this machine under conditions beyond the use of this machine. Please read this manual carefully before use.
2. Please clean the dirt in the dust box of the robot after use.
3. The cleaning robot should be stored in a cool and ventilated place, away from direct sunlight.
4. If the cleaning robot needs to be stored for a long time, it should be charged every three months to keep the battery power between 40% and 60%. Use only original and author-rated power adapters. If the cleaning robot is not charged for a long time, due to the self-discharge of the battery, the battery voltage will be lower than the over-discharge protection voltage, which may cause serious damage.
5. When putting the robot into or out of the swimming pool, you must lift the handle, and do not pull the cable. Before each start-up of the robot, the gas in the machine should be exhausted as much as possible (no more bubbles or the machine completely sinks to the bottom of the pool), so as not to affect the normal operation of the robot due to the presence of gas.
6. Make sure the pH value of the water in the swimming pool is 7.0-7.8.
7. It is strictly forbidden to put water treatment medicines into the machine and dispense them through the machine. The manufacturer is not responsible for the warranty if the machine is damaged.
8. If the product is used outdoors in a rainy, windy or strong light environment, it may affect the effect of recharging.

Product Description

This eco-friendly pool cleaning robot is a new type of rechargeable automatic cleaning robot that can filter pool water to achieve the effect of cleaning the pool.

1. Host
2. Dust box
3. Adapter
4. Float ball
5. Self-adaption recharge adaptor
6. Remote control
7. Mounting screws
8. Instructions
9. Charging station
10. 2.6ft Host Extension Cable
11. Expansion rubber plugs

Consumables details
The above parts are consumables. To avoid affecting the cleaning function of the product, please replace them in time after the expiration date. The above is the recommended replacement time, which is determined by the working performance of the product.

After-sale Support
Official website: www.lydsto.com
After-sales: service@lydsto.com
Technical support: support@lydsto.com

Basic parameters

Only supported in the following water conditions.

The light display and button description

Recharging stand light display and button instructions:

Description of the Self-adaption recharge adaptor

Remote control instructions

Screen instructions

Installation

1. Remove the product from the packaging.
2. Connect the self-adaption recharge adaptor to the host.
3. When the water depth is within the range of 3.9 to 5.2ft (1.2 to 1.8M), connect the connect-Wing to the street to prove owes connections which may ease charging allure, the finally fix the floating ball at a distance of 2.3 to 2.9ft (70 to 90cm) from the host unit.
4. hen the water depth is within the range of 5.9 to 8.2ft (1.8 to 2.5M), an extension cable of the adaptor is. to sure that each race has to have seeing rings and the tiny hates tightened securely. Finally, fix the floating ball at a distance of 2.3 to 2.9ft (70 to 90cm) from the host unit.

Notice
The installation of a floating ball is to prevent the entanglement of wires by the main unit due to different water depths. Users can adjust the height of the floating ball based on the specific water depth environment to achieve optimal performance. Install the recharging base at a suitable location. Please select a location at the poolside with a minimum lateral spacing of 1M and a minimum frontal spacing of 3M for the installation of the charging station.

Notice

1. Before installation, please confirm that the height from the water surface to the poolside is about 6in (15cm)*.
2. The charging station needs to be installed on the edge of the swimming pool at a deeper location, and the best installation depth is 3.9 to 8.2ft (1.2 to 2.5m).
3. (If the installation location is not within this range, may affect the effect of automatic recharge. It is recommended to install it at the deepest water level.)
4. The charging station installation position should avoid direct sunlight as much as possible, which may affect the effect of product recharging.

Notice

1. Do not install charging stations near the following areas:
2. Drill two holes with a diameter of M5 and a depth of 40mm at a horizontal distance of 50mm from the pool wall. The horizontal distance between the two holes is 200mm. Knock the expansion rubber plugs inside the accessory box into the holes.
3. Clean the dust and water stains in the installation area, remove the protective film of the adhesive tape, align the charging station with the hole for fixing and secure it with M5 screws.
4. Connect back to the charging station power supply.
5. Connect the adapter cable interface to the charging station, and ensure that the cable into the slot for charging the sealing ring (single) is intact and the station. Do not pull the cable too tightly fixing the nut is tightened securely;
6. when securing it, and make sure that the charging station can float up and down freely in the water.

Instructions

1. Start the device and put it in water.
2. Start the device with the remote control.
3. After use, turn on the recharge function for automatic recharge.
4. When entering or lifting out of the swimming pool, please do not touch the wall, so as not to scratch the wall or damage the cleaning robot.
5. Wait for the cleaning robot to leave the water for 10-15 seconds until it drains the internal water, and then take it out of the water.
6. After the cleaning of the robot is completed or the battery power is lower than 15%, it will automatically enter the recharging mode.
7. When taking it out of the water, please use the cable to lift the robot to the water’s surface, and then use the handle to lift it out.

APP instructions

1. Download the Lydsto APP from major app stores or App Stores.
2. Make sure your mobile smart device (phone/tablet) is connected to your home Wi-Fi network.
3. Make sure you have the Wi-Fi network name and password.
4. Make sure Bluetooth is enabled on the smart device.

Lydsto

1. Lydsto download the QR code
2. prepare the pool robotic to be connected.
3. Connect the pool robot to a power source.
4. Ensure Bluetooth is turned on on on the phone.
5. Simultaneously press the button on the remote control for 3 seconds, or press the “recharge button ” and “start-stop button ) ” on the recharge stand for 3 seconds at the same time, seeing that the indicator light on the self-adaption recharge adaptor flashes green and orange alternately, the wifi reset is successful, and the machine enters the distribution network mode.
6. Select “Lydsto P1 MAX”.
7. Enter the corresponding WIFI name and password to connect successfully.

• Using the Lydsto APP you can control the pool cleaner and know its working status:
  • Working Modes: Floor, Wall and All;
  • Function Button: Recharging, Start/ Pause control and enable Enhanced Mode;
  • The cleaner working state display: Cleaning Area, Cleaning Time and Battery Capacity;
  • Remote control in the secondary menu;
  • Other abnormal status pop-up information;
  •OTA Function: continuously upgraded and optimized;
  Note: In relatively clean water environments, ECO mode can be selected for longer working hours.

Daily maintenance
Note: To avoid affecting the suction of the product due to the clogging of the filter screen by garbage, The dust box should be cleaned promptly after use.

1. Pull the buckle and lift the cover
2. Take out the dust box
3. Open the buckle
4. Separate the filter and tray
5. Rinse the filter and tray with clean water
6. Assemble the filter and the tray, and fasten the buckle
7. Put the dust box back into the main host (note the direction of the dust box)
8. Close the cover

Troubleshooting

1. Everything is normal during the operation, but the robot will be stuck on the drain pipe or the solution of the dry cover: Please check whether there is any foreign matter stuck in the water inlet at the bottom.

2. The solution to the problem that the robot cannot run after launching into the water:

3. Check the display status of the self-adaption recharge adaptor light; if the self-adaption recharge adaptor light is off, please manually connect the self-adaption recharge adaptor to the charging base;

4. After recharging, restart the machine;

5. Please check whether there is any obstacle blocking the impeller, track or wheel;

6. If it still doesn’t work, please contact customer service.

7. The solution to the robot not responding after starting up:

8. Check the display status of the self-adaption recharge adaptor light; if the self-adaption recharge adaptor light is off, please manually connect it to the charging base;

9. If the indicator light is still off after connecting to the charging station, please contact customer  service to replace the component or machine;

10. How to ensure that the robot can be successfully charged?
    Observe the indicator light on the self-adaption recharge adaptor, if the indicator light is green and breathing, it means it is charging normally.

11. In the wall climbing mode, the solution to the difficulty or failure of the machine to climb the wall:

12. There is too much garbage in the dust box, causing the filter to be blocked. Please clean the filter;

13. The collodion of the roller brush is aging and the friction force is reduced. It is recommended to contact the official customer service to purchase replacement consumables.

14. When the robot is working, the solution is to spin in place or the path is abnormal, and it does not retreat after climbing the wall to the water’s surface:
    Please rinse the dirt attached to the ultrasonic sensor with clean water, and wipe off the dirt with a towel.

15. The solution to the slow running speed of the robot and weak suction power:

16. Clean the filter screen and check whether the filter tank is too dirty. If it is, it is recommended to clean it manually first, and perform daily maintenance on the product;

17. The power of the machine may be insufficient, and it must be cleaned after it is fully charged.

18. The solution to the decline in the cleaning ability of the machine compared to when it was first purchased:

19. The filter screen of the dust box is blocked when checking;

20. When checking the position of the track and impeller, it is stuck by foreign objects;

21. The APP shows that the life of the consumable is exhausted; it is recommended to contact the official customer service to purchase and replace the consumables.

22. The solution to the failure to recharge normally:

23. Check whether the host cable is entangled, please release the cable to a natural state and recharge it;

24. Check whether the infrared window of the self-adaption recharge adaptor and the recharging seat is covered by too much dust or other foreign objects, please clean the infrared window of the self-adaption recharge adaptor and the recharging seat;

25. If the continuous wind force exceeds 3 degrees, the self-adaption recharge adaptor may not be able to recharge normally.

26. Other unusual conditions, such as strong direct sunlight, rainy and large water waves.

27. The solution to recharging but not charging:

28. Check whether there is liquid on the electrode sheet of the recharger, please wipe off the liquid on the electrode sheet and try charging again;

29. Please check whether there is any stain on the surface of the electrode sheet. Please cut off the power  and polish the surface of the metal sheet with sandpaper to make the oxide fall off;

30. When checking the electrode sheet life of the recharging station through the mobile APP, it reaches the limit, please replace the electrode sheet of the recharging station;

31. If none of the above methods can solve the problem, please contact the dealer for after-sales treatment.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. Make sure it operates the equine proved by the party responsible for compliance could void the Sute Tho Part I of the ce elutes. lase fins are designed to promote personalised protel den against harmful interference in a residential installation. accordance with the lines actions, a caseHarioo frenterterence to radio communications on in- following measures:

• Reorient or relocate the receiving antenna.
• increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

ISED Statement

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Manufacturer Address
Hubei Yimu Electronic Technology Co., Ltd.
1 7-16-103 Modern Sino-Canada Science and Technology City, West of Yewang Road,
Shazui Street, Xiantao, Hubei Province, China
Official website: www.lydsto.com

After-sales
a service@lydsto.com
Technical support: support@lydsto.com

References

• Lydsto | Born for cleanliness | Robot Vacuum & Robotic Pool Cleaner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>