Lydsto P1 Robotic Pool Cleaner with Wall Climbing Instructions

Lydsto P1 Robotic Pool Cleaner with Wall Climbing

Precautions

Tips

Please read this manual carefully before using this product, and keep it properly.

  Safety Instructions!

1. This appliance can be used by adult. If persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge they must be given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.Cleaning and maintenance shall not be made by children without supervision.
2. Read the manual carefully and use the cleaning robot according to the instructions, we are not responsible for any loss or injury caused by improper use.
3. The appliance is only to be used with the unit provided.
4. The power must be off before cleaning or maintaining the appliance.
5. In case of parts damage or consumable replacement, please ensure the following two aspects: ➀ Through the manufacturer’s regular channels to purchase parts; ➁ Qualified technical personnel operation maintenance replacement.
6. Before the robot starts working, the dust box must be installed, otherwise hard foreign objects sucked in will cause damage to the motor blades.At the same time, it must be confirmed that the cable should be completely relaxed to avoid entanglement with the host and affect the cleaning effect.
7. When working, the power supply must be connected to a socket with leakage protection and grounding, and placed in a cool place at least 3.5M away from the edge of the swimming pool. Avoid placing or covering any objects to prevent damage to internal electrical components caused by overheating. Keep the adapter away from standing water.
8. When using, the operator must not touch the track and wheels to avoid damage.
9. Do not use the cleaning robot when people or animals are in the pool.
10. Do not use or store the cleaning robot near any heat source.
11. Do not pierce the shell of the robot with nails or other sharp objects, and do not knock, hit or throw the cleaning robot.

Caution

1. It is strictly forbidden to use this machine under conditions beyond the use of this machine. Please read this manual carefully before use.
2. Please clean the dirt in the dust box of the robot after use.
3. The cleaning robot should be stored in a cool and ventilated place, away from direct sunlight.
4. When putting the robot into or out of the swimming pool, you must lift the handle, and do not pull the cable. Before each start-up of the robot, the gas in the machine should be exhausted as much as possible (no more bubbles or the machine completely sinks to the bottom of the pool), so as not to affect the normal operation of the robot due to the presence of gas.
5. Make sure the pH value of the water in the swimming pool is 7.0-7.8.
6. It is strictly forbidden to put water treatment medicines into the machine and dispense them through the machine. The manufacturer is not responsible for the warranty if the machine is damaged.

Product Description

This eco-friendly pool cleaning robot is a new type of automatic cleaning robot that can filter pool water to achieve the effect of cleaning the pool.

1. Host

2. Power supply unit

3. Dust box

4. Remote control

5. Instructions

Consumables details

1. Roller brush

2. Medium brush

3. Track

The above parts are consumables. To avoid affecting the cleaning function of the product, please replace them in time after the expiration date.
*The above is the recommended replacement time, which is actually determined by the working performance of the product.

After-sale Support

Official website : www.lydsto.com
After-sales : service@lydsto.com
Technical support : support@lydsto.com

Basic parameters

Host

Power supply unit

Product mode| KZH-P1-W01
KZH-P1-W03
---|---
Input| 100-240V~ 50/60Hz
Output| 24V ⎓  8.3A
Waterproofing class| IPX6
Operating Temp| 32~104℉(0~40℃)
Product Size| 10.3×7.1×3.3inch

Remote control

Only supported in the following water conditions

wall-climbing performance may be affected.
NaCl| ≤5000 PPM

Light Display And Button Description

Host button description:

Power supply unit light display and button instructions:

Button instructions

“2H”
| Mode button| Switch between the three working modes of “wall”, “floor”, and “all”
| Network distribution mode| Long press 3S at the same time to enter network distribution mode

Light display

host after the power is turned on
DC line communication abnormality
WiFi light| Breath display every 2 seconds| WiFi not connected to the network
Fast flashing once every 0.5 seconds| WiFi enters distribution network mode
Light on| WiFi connected successfully
“1H”light| Flashing once per second| Water pump error
“2H”light| Motor error
“3H”light| Ultrasound error
“ALL”light| Gyroscope error

Remote Control Instructions

approach the swimming pool wall
| Direction and start and stop buttons| The direction keys can remotely control the cleaning robot for manual cleaning.
The start and stop button can start and stop the current working mode.
| Mode button| Press to switch between floor mode, wall mode, floor +wall mode.
| WiFi resetting button| Long press 3S to enter network distribution mode
| Timer button| Switch between three working hours: 1H, 2H, 3H.

Screen instructions:

Installation

1. Remove the product from the packaging.
2. Connect the power supply unit to the host.
   

Instructions

1. Start the device and put it in water.
2. Start the device wi the the remote control or function buttons on the power supply.
3. When entering or lifting out of the swimming pool, please do not touch the wall, so as not to scratch the wall or damage the cleaning robot.
4. Wait for the cleaning robot to leave the water for 10-15 seconds, until it drains the internal water, and then take it out of the water.
5. When taking it out of the water, please use the cable to lift the robot to the water surface, and then use the handle to lift it out.
   

APP Instructions

1. Download the Lydsto APP from major app stores or App Stores.

2. Make sure your mobile smart device (phone/tablet) is connected to your home Wi-Fi network.

3. Make sure you have the Wi-Fi network name and password.

4. Make sure Bluetooth is enabled on the smart device.
   Lydsto download QR code
   

5. Prepare the pool robotic to be connected.

6. Connect the pool robot to a power source.

7. Ensure Bluetooth is turned on on on the phone.

8. Simultaneously press the ” ” button on the remote control for 3 seconds, or press the “working hours button ” and “mode button ” on the power supply unit for 3 seconds at the same time, seeing that the WiFi light on the power supply unit Fast flashing once every 0.5 seconds, the wifi reset is successful, and the machine enters the distribution network mode.

9. Select “Lydsto P1”.

10. Enter the corresponding WIFI name and password to connect successfully.

Using the Lydsto APP you can control the
pool cleaner and konw it working status:

• Working Modes: Floor,Wall and All;

• Function Button: Start/ Pause control;

• The cleaner working state display:
  Cleaning Area,Cleaning Time,Water
  Temperature;

• Remote control in the secondary menu;

• Other abnormal status pop-up information;

• OTA Function: continuously upgraded and optimized;
  

Daily Maintenance

Note : In order to avoid affecting the suction of the product due to the clogging of the filter screen by garbage, The dust box should be cleaned promptly after use.

1. Pull the buckle and lift the cover.
   

2. Take out the dust box.
   

3. Open the buckle.
   

4. Separate the filter and tray.
   

5. Rinse the filter and tray with clean water.

6. Assemble the filter and the tray, and fasten the buckle.

7. Put the dust box back into the main host (note the direction of the dust box).

8. Close the cover.

Troubleshooting

1. Everything is normal during the operation, but the robot will be stuck on the drain pipe or the solution of the dry cover:
   Please check whether there is any foreign matter stuck in the water inlet at the bottom.

2. The solution to the problem that the robot cannot run after launching into the water:

3. Check the display status of the power supply unit light; if the power supply unit light is off, please manually connect the the power supply unit to the socket;

4. Restart the machine;

5. Please check whether there is any obstacle blocking the impeller, track or wheel;

6. If it still doesn’t work, please contact customer service

7. The solution to the robot not responding after starting up:

8. Check the display status of the power supply unit light; if the power supply unit light is off, please manually connect the power supply unit to the socket;

9. If the indicator light is still off after you connect to the socket, please contact customer service to replace the component or machine;

10. In the wall climbing mode, the solution to the difficulty or failure of the machine to climb the wall:

11. There is too much garbage in the dust box, causing the filter to be blocked. Please clean the filter;

12. The collodion of the roller brush is aging and the friction force is reduced. It is recommended to contact the official customer service to purchase replacement consumables.

13. When the robot is working, the solution is to spin in place or the path is abnormal, and it does not retreat after climbing the wall to the water surface:
    Please rinse the dirt attached to the ultrasonic sensor with clean water, and wipe off the dirt with a towel.

14. The solution to the slow running speed of the robot and weak suction power:
    Clean the filter screen and check whether the filter tank is too dirty. If it is, it is recommended to clean it manually first, and perform daily maintenance on the product.

15. The solution to the decline in the cleaning ability of the machine compared to when it was first purchased:

16. The filter screen of the dust box is blocked when checking;

17. When checking the position of the track and impeller, it is stuck by foreign objects;

18. The APP shows that the life of the consumable is exhausted; it is recommended to contact the official customer service to purchase and replace the consumable.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
   operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note :This equipment has been tested and found to comply with the limits for a class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.if this equipments does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an autlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Customer Support

Manufacturer Hubei Yimu Electronic Technology Co., Ltd.
Address 7-16-103, Hyundai China-Canada Science and Technology City, west of Yewang Road, Shazui Street, Xiantao City, China
Official website www.lydsto.com
After-sales service@lydsto.com
Technical support support@lydsto.com

References

• Lydsto | Born for cleanliness | Robot Vacuum & Robotic Pool Cleaner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>