FEIT Electric BALL-1/LED Balloon Light White + RGBYO Installation Guide
- June 7, 2024
- Feit Electric
Table of Contents
FEIT Electric BALL-1/LED Balloon Light White + RGBYO Installation Guide
Questions, problems, missing parts? Before returning to the store,
call Feit Electric Customer Service
8 a.m. – 5 p.m., PST, Monday – Friday
1-866-326-BULB (2852)
FEIT.COM
We appreciate the trust and confidence you have placed in Feit Electric
through the purchase of this LED Balloon Light. We strive to continually
create quality products
designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs.
Thank you for choosing Feit Electric.
Safety Information
Read and understand all Safety and Operating instructions in this manual
before using this product.
Follow all safe guards stated in the manual, in addition to normal safety
precautions in working with electrical devices. Always follow basic safety
precautions to reduce the risk of fire, electric shock and personal injury.
- Do not use with an extension cord near water or in areas where water may accumulate. Keep the balloon light at least 16ft. from pools or spas. Keep plugs dry. Only use this balloon light with GFCI-protected outlets.
- To disconnect, turn off the switch, then remove the plug from the outlet. Do not turn off by pulling on the cord.
- Do not insert foreign objects into this product.
- To reduce the risk of fire, keep away from combustible materials while in operation.
- To reduce the risk of injury, close supervision is necessary when this product is used near children.
SAVE THESE INSTRUCTIONS
Supplier’s Declaration of Conformity:
47 CFR § 2.1077 Compliance Information
Responsible Party:
Feit Electric Company
4901 Gregg Road,
Pico Rivera, CA 90660, USA
562-463-2852
Unique Identifier: BALL-1/LED
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help. Any changes or modifications not expressly
approved by the manufacturer could void the user’s authority to operate the
equipment.
Limited Warranty
This product is warranted to be free from defects in workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us or call 1-866 326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Pre-Assembly
HARDWARE INCLUDED
NOTE : Hardware not shown to actual size
PARTS OF THE BALLOON LIGHT
Installation
-
Take out the support rod (BB) from the bag.
-
Loosen Hand Screw 1, then partially pull out the legs of the tripod(see Fig. 1). Pull up to adjust the width of the legs of the tripod
(see Fig. 2).
-
Once the tripod legs have been adjusted to the desired position, tighten Hand Screw 1 to set into place. Loosen Hand Screw 2 and
pull up the support rod to adjust the height of the fixture. Tighten Hand Screw 2 to set into place.
-
Take out the balloon from the bag
5.
Insert the balloon (AA) onto the tripod and plug the toggle switchof the
balloon (AA) to the support rod (BB) 5
6. Now plug it into the main outlet and turn it on by using the toggle switch on the balloon (AA)
How to Select a Light Color
Adjust your light color anytime by toggling through the switch
To change the color, toggle your light switch ON and OFF within 2 seconds to cycle through the six colors (White, Red, Green, Blue, Yellow, Orange). Stop once the desired color is selected.
NOTICE : The toggle switch is located on the balloon.
NOTE : If the fixture is left OFF for more than 5 seconds, it will remember the last color selected and will display that color when turned on again.
WWW.FEIT.COM
Please contact 1-866-326-BULB (2852) for further assistance.
References
- Energy Saving Light Bulbs, Light Fixtures | CFL, LED & More
- Contact Us - Feit Electric
- Energy Saving Light Bulbs, Light Fixtures | CFL, LED & More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>