LNC A03195 Exterior Porch Light Fixture Instruction Manual

June 1, 2024
LNC

LNC A03195 Exterior Porch Light Fixture

LNC-A03195-Exterior-Porch-Light-Fixture-PRODUCT

Product Information

  • Specifications
    • Mounting plate assembly (A) – Quantity: 1
    • Green ground screw (B) – Quantity: 1
    • Backplate (E) – Quantity: 1
    • Threaded ball (F) – Quantity: 2
    • Stud (G) – Quantity: 2
    • Gasket (H) – Quantity: 2
    • Lid (I) – Quantity: 1
    • Cage (J) – Quantity: 1

Product Usage Instructions

  • Assembly and Installation
    • Remove the fixture from the carton and ensure all parts and accessories are included.
    • Turn off the power.
    • Install bulbs by carefully aligning the cage (J) to the lid (I), placing gaskets (H), and threading the studs (G).
    • Pull outlet box wires through the mounting plate assembly (A) and attach it to the outlet box with mounting screws (C).
    • Make wire connections following the provided colour chart and instructions. Do not connect wires to the ground wire.
    • Wrap wire connections with electrical tape and tuck all wires into the outlet box.
    • Ensure everything is properly installed before turning on the light.
  • Cleaning Instructions
    • To clean, wipe the fixture with a soft cloth. Use a mild soap for cleaning the glass. Avoid abrasive materials such as scouring pads, steel wool, or abrasive paper.
  • Ordering Parts
    • Keep the instruction sheet for future reference and part ordering. Replacement parts can be ordered from the place of purchase using the exact wording from the illustration.

FAQs

  • Q: Can I exceed the maximum bulb capacity recommended on the socket?
    • A: No, please do not exceed the maximum capacity recommended on the socket to ensure safety and proper functioning of the fixture.
  • Q: Do I need to hire a licensed electrician for installation?
    • A: It is suggested to have the fixture installed by a licensed electrician to reduce the risk of fire, electric shock, or injury to persons.

INTRODUCTION

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

  1. We suggest installation by a licensed electrician.
  2. Please read the instructions carefully and save them as you may need them at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
  4. The mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before the fixture.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
  7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
  8. When replacing the bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED)

Before doing assembly and installation please prepare the needed tools as below picture

LNC-A03195-Exterior-Porch-Light-Fixture-FIG-1 \(2\)

PARTS

PARTS TYPE & QTY INCLUDING:

  • (A) Mounting plate assembly (1)
  • (B) Green ground screw (1)
  • (E) Backplate (1)
  • (F) Threaded ball (2)
  • (G) Stud (2)
  • (H) Gasket (2)
  • (I) Lid (1)
  • (J) Cage (1)

ACCESSORIES & QTY ENCLOSED:

  • (C) Mounting screw (2)
  • (D) Plastic Wire Connectors (3)

ASSEMBLY & INSTALLATION

ASSEMBLY & INSTALLATION INSTRUCTIONS:

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
  2. Turn off power
    • Before you start to make an installation, NEVER attempt any work without shutting off the electricity until the work is done.
    • A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    • B). Place the wall switch in the “OFF” position.
  3. Unscrew the threaded balls (F) from the mounting plate assembly (A) then carefully remove the mounting plate assembly (A). Unscrew the studs (G) from the top of the lid (H), and gently remove the cage (J) and the gaskets (H) from the lid (I).
  4. Install bulbs (Not included. Please do not exceed the maximum capacity recommended on the socket.) Carefully pull the cage (J) to the lid (1), then gently rotate the cage (J) to make the holes in the lid (H) and the cage (J) are aligned, then place the gaskets (H)and thread the studs (G)till sung.
  5. Carefully and gently pull the outlet box wires through the mounting plate assembly (A). Attach mounting plate assembly(A) to outlet box with mounting screws (C).
  6. Make wire connections
    • Connect wires as below wires connecting shown below. TAKE NOTE OF THE WIRE COLOR OF THE FIXTURE, NEVER CONNECT WIRE TO GROUND WIRELNC-A03195-Exterior-Porch-Light-Fixture-FIG-1 \(7\)
    • Twist plastic wire connector (D)until wires are tightly joined together, wrap each connector with approved electrical tape and carefully tuck all wires into the outlet box
  7. Align the holes in the back plate (E) with the mounting screws, then attach the canopy (E) using the previously removed threaded balls (F). Hand tighten until snug.
    • Note: The canopy (A) should be snug against the wall and the mounting balls. If not, adjust the length of the nipples on the mounting plate assembly (A) by unscrewing the preassembled hex nuts and then screwing the mounting screws in or out of the mounting plate until the length is achieved. Tighten the hex nuts and proceed to the step 7
  8. Check everything is already installed properly, and then you can turn on the light. Enjoy!

CLEANING

  • To clean, wipe the fixture with a soft cloth.
  • Clean glass with a mild soap.
  • Do not use abrasive materials such as camping pads or powders, steel wool or abrasive paper.

ORDERING PARTS

  • Keep this sheet for future reference, and in case you need to order replacement parts.
  • All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LNC User Manuals

Related Manuals