DONGGUAN SMALL WORLD NOVELTY CO LTD 19016 Rechargeable Remote Controller Instructions

June 1, 2024
DONGGUAN SMALL WORLD NOVELTY CO LTD

DONGGUAN-logo

DONGGUAN SMALL WORLD NOVELTY CO LTD 19016 Rechargeable Remote Controller

DONGGUAN-SMALL-WORLD-NOVELTY-CO-LTD-19016-Rechargeable-Remote-Controller-
product

Specifications

  • Product Name: Rechargeable Remote Controller Vibrator
  • Charging Method: USB cable with magnetic pin
  • Charging Time: Approximately 60 minutes for full charge
  • Usage Time: Up to 20 hours
  • Cleaning: Use water-based wet wipes to clean
  • Waterproof: The remote controller is not waterproof

Charging

Charge your vibrator by connecting the USB cable to the magnetic pin. It takes about 60 minutes to fully charge.

Power On/Off
To activate the product from standby mode, click the power button on the remote. Press the power button again to turn the product off.

Intensity and Patterns
Use the +/- buttons to increase or decrease intensity. Press the right function button to cycle through different patterns. Press the left function button to go back to the previous pattern.

Cleaning

The remote controller is not waterproof, so do not wash it under water. Use water-based wet wipes to clean any dirt.

  • PMN: rechargeable remote controller
  • Charge your vibrator by connecting the USB cable to the magnetic pin.
  • The toy will take approximately 60 minutes to fully charge and will give you up to 20 hours of play.
  • Click the power button on the remote to activate the product from standby mode.
  • Press the +/- buttons to increase/decrease intensity.
  • Press the right function button to move through the patterns.
  • Press the left function button to return to the previous pattern.
  • Press the power button on the remote control to turn the product off.
  • The remote is not waterproof, please don’t wash it under water. Use water-based wet wipes to clean the dirt.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

ISED Statement
English: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.  The digital apparatus complies with Canadian CAN ICES – 3 (B)/NMB – 3(B). This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals