madimack i30 GT Freedom Cordless Robotic Pool Cleaner Instruction Manual

madimack i30 GT Freedom Cordless Robotic Pool Cleaner

Specifications

THANK YOU
Congratulations on purchasing Madimack`s innovative GT Freedom cordless robotic cleaner! We are so happy that you chose our brand to partner with. The Madimack GT Freedom represents a new era in cleaning technology, and we are thrilled that you
are now a proud owner. With its cutting-edge features, intelligent navigation, and powerful performance, this robotic cleaner is set to revolutionize your cleaning routine and provide you with unmatched convenience.

We are committed to your satisfaction and are here to support you throughout your ownership journey. Should you have any questions, or feedback, or require any assistance with your new Madimack GT Freedom cordless robotic cleaner, please visit our website which is just a click away www.madimack.com.

Once again, congratulations on your purchase! Enjoy getting to know one of our favorite products, the GT Freedom.
Warm regards,

Alex Welsh Madimack Global CEO

warning: PLEASE READ THE MANUAL CAREFULLY BEFORE INSTALLATION & OPERATION AND RETAIN IT FOR FUTURE REFERENCE.
Adherence to the directions for use in this manual is extremely important for health and safety. Failure to strictly adhere to the requirements in this manual may result in personal injury, and property damage and affect your ability to claim Madimacks warranty provided with your product. Products must be used, installed, and operated under this manual. You may not be able to claim the manufacturers warranty if your product fault is due to failure to adhere to this manual.

WARNINGS
This page contains information that will help you operate the robot safely, prevent hazards, and prevent damage to the robot or other property.

General Warnings

• Keep the robot out of reach of children or persons with reduced physical, sensory, or mental capabilities without supervision or instruction

• Read the instructions before operating the robot.

• Keep the robot out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

• The robot must be maintained by the dealer except for simple routine maintenance written in this manual.

• Installers must follow the manufacturer`s instructions and keep in compliance with national or local standards for installation. Under no circumstances will the manufacturer be held responsible for any outcome incurred by failure to comply with applicable standards or local regulations.

• Incorrect installation or use of the robot may cause serious damage to property or injuries
  to people.

• Do not enter the pool while the robot is in the water.

Warnings On Use

• Only use the detachable supply unit provided with the robot to recharge the battery.
  Operate the power supply at least 3.5 meters from the edge of the pool

• Disconnect the robot from the power supply and insert the magnetic cap back in place before performing any maintenance on the robot

• Disconnect the robot from the supply mains before carrying out the user

• Do not try to repair the robot yourself or open the engine box in case of malfunction, please contact your dealer.

• If there is any malfunction or release of odor from the robot when charging, disconnect it from the power supply immediately and contact your dealer.

• Use only original replacement parts supplied by the manufacturer for service and repair.

General operation conditions for robotic pool cleaner

• The robot is intended to operate in pools between 0.4 and 3m depth.
  The robot can operate in a pool temperature between 4 and 35 degrees (below 15 degrees may affect endurance time).

•  The robot will automatically stop running if the water depth is less than 40 centimeters for motor protection.

• Do not use the robot during shock chlorination.

• Do not use the robot in a thunderstorm or stormy weather.

• Do not expose the robot to direct rainfall or sunlight for an extended period.

  • The robot is intended to be used with a balanced pool between PH 7.0-7.8, NaCI:5000 ppm Max, and Chlorine 4 ppm Max.

CAUTIONS

• Rest/hold the robot by the pool edge for water to drain out before lifting the robot out of water, do it slowly to prevent back injury.
• Clean the filter basket after each cleaning cycle.
• Do not lift the robot out of the water by track.

warning: For battery protection, the robot should be fully charged every 3 months and the magnetic cap should be inserted back into the robot if it is not being used for more than 14 days.

NOTICE: When the robot battery is below 30%, it will only clean the floor of the pool.

How to achieve the most efficient cleaning
Place the robot at the corner of the pool for quick coverage of the entire pool floor area.

How to drain water from the robot
Place the robot on the edge of the pool for a while and let the water drain out.

How to open the filter box

WARNING: For battery protection, the robot should be fully charged every 3 months and the magnetic cap should be inserted back into the robot if it is not being used for more than 14 days.

Do not charge the robot outdoors.

Do not long-term expose the robot to the sun.

PRODUCT OVERVIEW

Packaging content
The following items are included in the packaging of a robot. Please contact your dealer if any damage or loss.

1. GT Freedom robot
2. Charger
3. Hook
4. Magnetic cap*2
5. User manual

NOTE:

1. Remove the Magnetic Cap 2 when using or charging. Insert a Magnetic cap to machine`s bottom for battery protection when not using the robot for more than 14 days.
2. If the robot fails, insert the magnetic cap into the robot for 2 seconds, remove the magnetic cap, and restart the robot i.e. reset the robot.

Technical specification

72hr
3D S Path w th InverMac| YES
 pp appl cat on| YES
F lter capac ty| 3 2L
F ltrat on accuracy| 180μm 80mesh
|

300 – 150 L/m n

| 360L – 160

L/m n

Runn ng power| 30-110W
Mov ng speed| 12m/m n
Motor number| 3
Charger nput| 90-265V C ~ 50/60 z
Runn ng voltage/current| 25 2V/1 2
Charger power| 72 5W
Robot NW| 11 5kg| 11 5kg| 12kg| 12kg
Robot GW Sh pp ng| 16 5kg| 16 5kg| 17kg| 17kg
Robot d men on LW| 495395265 mm
Robot package ng d me on

LW

| ****

580448330 mm

Reference: The above working time is based on 2 hours cleaning time at floor mode in a pool.
Note: The manufacturer reserves the right to modify these specification without notice.

Preparation

1. Remove the Magnetic cap from the bottom of the robot and store it well.

2. Remove the plug cover. When fully charged, cover the plug again.
   

3. Connect to the power supply using the charger supplied. The red light indicates charging The green light indicates power and a fully charged robot Fully charge the robot before use

4. Install the configured hook on the rod (Rod is exclusive).

OPERATION

To prevent possible damage to the robot or people, be sure to follow these guidelines:

• a. After cleaning is completed, place the robot in a cool dry place away from direct sunlight.
• b. Take care when removing the robot from the pool and allow water to drain from robot before lifting.

IMPORTANT

• Once the robot is set up, drop into the water within 3 minutes or the robot will enter sleep mode.
• Clean the filter basket after the cleaning cycle. Avoid cleaning the surface of the filter box directly with your hands.
• The robot has a safety feature that automatically stops if a dry run happens.
• Turn the robot in all directions to release any air trapped in the robot before it enters the water. Shown below.

Overview of Control Panel

Note: If the cleaning time is set to be more than 2 hours via App, there will also be 3 lights on.

Operation on the display of the unit

1. Hold for 3 seconds to activate the robot. a sound will chime and the will start to flash.
2. The robot is now in set-up mode

Set clean time, cleaning operation , and repeat clean mode where necessary by pressing the buttons on the control panel. See the above table for more information
Once setup is complete there are two options to run the robot

1. Press will becomes solid light. The robot is now ready to be placed into the water and will start cleaning once reaches the bottom of the pool.
2. Press and hold for 3 seconds and the panel will beep once and go into standby mode. The robot will automatically start the cleaning cycle after the delayed amount of time set by the cycle mode.
   For example, if you set it to repeat every 24 hours, the robot will delay for 24hours before first cleaning cycle, this is the same for 48 hours and 72 hours setting

Active Panel Tips

1. Red power light flashing – set up mode
2. Red power light solid – run mode
3. Panel off – standby mode
4. Magnet fitted to base – unit off

If the battery drops to less than 15% during the cleaning cycle the robot will start to finish the cleaning cycle and move to the poolside ready for shutdown. It will enter sleep mode after 5 mins

Cleaning the filter Basket

• When a cleaning cycle is complete, the robot will stop at the wall of the pool. Use the hook to catch the handle and lift the robot out of the water.
• Drain the water from the robot and clean the filter basket as shown below:

TIP! Only spray with a gentle hose, do not use high pressure or basket filter may tear, If filter does not come fully clean use a soft bristle brush to release fixed dirt

Note: To prevent injury, wear rubber gloves when cleaning the filter basket.

Charging the robot

1. Plug the adapter into the power supply and make sure that the indicator light is red.
2. Open the cover of the robot`s plug to expose the plug charging port.
3. Plug the adapter plug into the robot. When the robot is charging, the battery light of the robot flashes green and the indicator light on the adaptor is red.
4. If the battery light is full with 3 green lights on, and the indicator light of the power adapter goes green, then the robot is fully charged.
5. Before charging, make sure the charging port is dry.
6. It is recommended to disconnect the charger after charging is completed to protect the battery.
7. If the robot needs to be stored for a long time, it should be fully charged at least every three months to protect the battery.
8. It is not recommended to charge outdoors. at least every three months to protect the battery.

Note: Use the original power adaptor with the robot ONLY.

WIFI Matching

QUICK TIPS.

1. Place GT Freedom close to the router
2. Switch bluetooth on, on the phone
3. Accept pop-up prompts when first starting the app
4. WiFi cannot be used while the robot is in water due to the limitations of signals penetrating water.

First download the “Ai Bot” application from the mobile app store. Set up the app ready for connecting by following the on-screen set up.
Once ready press to add device press and hold symbol starts flashing green.

Follow mobile app prompts to complete setup

After pairing the mobile app

• Set the clean duration in 10-minute increments.
• Set cycle schedules
• Battery indicator

Turn On the robot.

Turn on bluetooth on your phone/tablet Hold the floor and wall button, for 3 seconds until the robot beeps and the WIFI button starts flashing.
Open the AI BOT App and sign up or login

• Press add device.
• The APP will search for your robot
• Press add in the Discovering Devices section There will be a prompt to connect to WIFI if you have not already done so. Once connected, the robot name should appear in your add device section.

The WIFI button will flash to indicate matching. This takes between 30 and 45 seconds. Once complete, binding completed will be displayed on your phone/ tablet screen and the WIFI button on the robot will stop flashing
You can now setup and control your robot from your tablet/phone mobile app

MAINTENANCE

WARNING

• To avoid electric shock and other hazards that could result in major injuries, disconnect the adapter from the power source before performing any cleaning and maintenance.
• Before any maintenance and to avoid injuries caused by impeller rotation, insert the magnetic cap at the bottom of the robot.

Filter maintenance

• Clean the filter thoroughly and regularly for better cleaning and climbing performance. Otherwise, the cleaning and climbing performance may be affected when the filter if full or clogged.
• Clean the clogged filter with mild acidic detergent, and it is recommended to clean it at least once a year.

Impeller maintenance
Visually check whether the impeller or impeller shaft is entangled with hair or other debris when the robot has a reduced suction or climbing performance, clean the debris trapped in the impeller. *Magnetic MUST be inserted into the robot before any maintenance on the impeller.

Follow the below steps

• Take out the filter box, remove the fixing screws of the inflow ring cover, and take out the inflow ring cover.

• Remove the deflector fixing screws and take out the deflector.

• Remove the impeller screw and take out the impeller.
  Note: Wear gloves when removing the impeller to prevent injury from sharp edges.

• Clean the impeller debris and reassemble all the parts mentioned above in order.

Note: If you have any difficulties with impeller maintenance, contact your dealer for assistance.

Replace the worn brushes
Remove the worn brushes & position the new brushes.

1. Unfasten the tabs from the holes and remove the brushes.
2. Fit the side without tabs under the brush holder.
3. Roll the brush around its support, slide the tabs into the attachment holes, and pull on the end of each tab until its edge passes through the slit.
4. Replace the worn tracks
   Remove the worn tracks. Position the new tracks:

Troubleshooting

Charg ng fa lure

| Debra s on the electrode of charge ng head (Non-fa lure)| ****

Clean deb s

The bottom Magnet c cap

sn t removed (Non-fa lure)

| ****

Remove the Magnet c cap

Charger s damaged| Replace charger

Sw tch on fa lure

| The Magnet c cap sn t removed (Non-fa lure)| ****

Remove the Magnet c cap

Water spots on the robot d splay or people s hands (Non-fa lure)| Keep the display and hands dry, then try again

No power n the battery (Non-fa lure)

| ****

Get the robot fully charged

Not work ng (not mov ng, not pump ng)

| Low battery (Non-fa lure)| Get the robot fully charged

Out of water (Non-fa lure)

| Make sure the robot s submerged underwater and

nd cator l gets be ng on

No press ng the on/off button after sett ngs are done

(Non-fa lure)

| Press the on/off button after the settings are done, make sure

nd cator l gets be ng on before putt ng the robot into water

(Non-fa lure)

| ****

Mov ng but not pump ng

| ****

The impeller gets stuck

| Check whether there s deb s

n the gu de r ng, affect ng the rotate on of the impeller. (Please

insert back the magnet c cap before operating on, to avoid

njur es caused by the impeller rotating.

fa lure)

|
Water nlet s blocked(Non- fa lure)|

clean water nlet

Battery low (Non-fa lure)| Get the robot fully charged
Failure| Possible reason| Solution
---|---|---

Pumping but not moving

| ****

The moving motor gets stuck

| Please contact the dealer for a replacement

The track is deviated and stuck (Non-failure)

| Turn the robot upside down and roll the track forward and backward to restore the track
Track is damaged| Replace track
Scrubber gets stuck (Non-failure)| ****

Clean scrubber

The robot gets stuck by an obstacle and shut down for auto-protection (Non- failure)| ****

Remove the obstacle and restart

(Non-failure)

| ****

Not climbing

| ****

(Non-failure)

| ****

Turn to overall cleaning mode

The impeller is stuck

| Check whether there is debris in the guide ring affecting the rotation of the impeller. (Please insert back the magnetic cap before operation to avoid injuries caused by the impeller rotation.

(Non-failure)

|
The water inlet is blocked (Non-failure)|

clean the water inlet

Poor cleaning capability

| Battery low (Non-failure)| Get the robot fully charged

The impeller is stuck

| Remove any debris or hair in the guide ring

failure)

| ****

Water inlet blocked (Non-failure)

| ****

clean water inlet.

Scrubber is damaged| Replace scrubber
The filter basket is damaged| ****

Water chemistry is unbalanced

| Fix water chemistry high PH in particular can cause climbing issues

Unusual non-stop

| ****

Software failure

| Insert the magnetic cap back to the bottom for 5s then remove it and restart

Exploded view

NOTE

• Do not use the robot when people or animals are in the pool.
• Charger MUST BE DISCONNECTED before conducting any maintenance on the robot.
• Contact your dealer for problems not covered in the Trouble Shooting Guide.
• Normally, the robot will stop at the poolside when it encounters any failure
  or finished its cleaning cycle. – If an error occurs, please restart the robot by placing the magnetic piece the underside of the robot – If the robot is malfunctioning, an error code will appear on the operation panel (see 2.1) and the power button on the operation panel will flash red. Pressing the power button ( ) will remove the error warning and allow operation, if an error occurs again, please check the troubleshooting guide

Spart parts list

WARRANTY & EXCLUSIONS

STANDARD CONDITIONS – Australia and New Zealand
Madimack Pool Products Pty Ltd distributes pool products and provides the following warranties:

STATUTORY RIGHTS

• The benefits to the consumer under this warranty are in addition to other rights and remedies of the consumer under the laws about the goods and services to which the warranty relates.
• Our goods come with guarantees that cannot be excluded under Australian Consumer Law. You may be entitled to a replacement or refund for a major failure and compensation for any other loss or damage. You are also entitled to have the goods repaired if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

LIMITED WARRANTY

• Madimack warrants that its products are free from defects in materials and manufacture for 3 years from the date of purchase unless otherwise specified. Please visit www.madimack.com.au for all warranty terms and conditions
• Madimack will, at its discretion, repair or replace any product proven to be defective during the warranty period for either materials or manufacture. Alternatively, Madimack will pay the cost of repair or replacement within 90 days of receiving the defective product, subject to unforeseen delays. This warranty is applicable for domestic installations only, is personal to the original purchaser, and does not transfer to any subsequent purchasers.

EXCLUSIONS

• To the extent permitted by law, Madimack excludes all statutory or implied conditions and warranties, as well as any other liability that may arise under statute or at law, including without limitation liability for breach of contract, negligence, or any other cause of action. The following exclusions apply:
• Incorrect operation of the unit resulting from failure to follow the provided instructions. Damage caused to the robot due to misuse or any means other than a manufacturer defect. Repairs or servicing performed by unauthorized dealers or service stations. Damage caused by an unauthorized service station that compromises the battery seal.
• Overcharging the battery by using a non-specified input power adapter. Faults in the machine’s operation caused by the use of non-specified accessories. General wear and tear of consumable products, including filters, tracks, and brushes.

LIMITATION OF LIABILITY
To the extent permitted by law, Madimack’s liability under any condition or warranty that cannot be legally excluded with the supply of goods and services is limited to one of the following options:

• Repairing the goods.
• Replacing the goods with equivalent products or services.
• Paying the cost of replacing the goods or providing equivalent products or services again.
• Paying the costs of repairing the goods.

PROCEDURE FOR WARRANTY CLAIMS

• In the event of a warranty claim, the faulty product must be returned to the place of purchase or, if installed by an approved agent, to an authorized warranty agent. Madimack does not accept returns directly from end consumers.

• You are responsible for arranging the removal of the defective product and the installation of the repaired or replacement product. This includes all transportation costs and any applicable insurance fees associated with transporting the products to the supplier and the replaced or repaired product from
  the supplier.

• All returns require Madimack’s written approval and must be accompanied by either:

• A Field Inspection Report authorized by the Local Customer Service Manager or Authorized Agent, or

• A “Return Goods Authorization”

INDOOR
For switch power supply indoor use only.

Recycling
When disposing of the product, please hand it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of waste equipment at the time of disposal will help ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local authority

This guide may be updated without notice.
Visit the official Madimack website for the latest version: https://www.madimack.com.au

madimack.com.au

FAQ

Frequently Asked Questions

Q: How often should I charge the robot?

A: The robot should be fully charged every 3 months and if not in use for more than 14 days, insert the magnetic cap for battery protection.

Q: How do I drain water from the robot?

A: Place the robot on the edge of the pool and allow water to drain out.

References

• Sustainable Pool Heating and Pool Heater Supplier | Madimack
• Madimack Global Home
• Sustainable Pool Heating and Pool Heater Supplier | Madimack
• Sustainable Pool Heating and Pool Heater Supplier | Madimack

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>