TARAMPS TS 800X4 Multi-Channel Amplifier Instruction Manual
- June 13, 2024
- TARAMPS
Table of Contents
TARAMPS TS 800X4 Multi-Channel Amplifier
The installation of this product must be made by a qualified professional
Term of warranty
TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of a defect during the warranty period, TARAMPS’ responsibility is limited to the repairing or replacement of the device of its own making.
This warranty excludes:
- Damaged products by improper installation, water infiltration, and violation by unauthorized individuals;
- Tamper or torn warranty seal;
- Cases in which the product is not used in adequate conditions;
- Defects caused by accessories, modifications or features attached to the product;
- The product with damage from falling, bumps or nature-related problems (flooding, lightning, etc);
- Warranty card is not properly filled or torn;
- Costs involving uninstallation, reinstallation of equipment as well shipment to the factory;
- Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.
Technical assistance
For international support, check on our website: www.taramps.com.br/en/rede-
de-assistencias-tecnicas or contact direct factory support:
E-mail: service@taramps.com.br
Phones : +55 18 3266-4050 / +55 18 99749-3391
Introduction
Read this manual before preparing the product. In case of doubt, contact our
technical support: (18) 3266-4050 or
www.taramps.com.br.
At the end of its useful life, this product must not be disposed of in
household waste. Look for an electronic equipment collection or recycling
center for proper disposal.
Declaration of Conformity
TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil Hereby, Taramps
Electronics Ltda declares that the product TS 800X4 complies with the
Directive 2014/30/EU, according with the following harmonized standard:
-EN 50498:2010 Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles The full text of the EU Declaration of Conformity is available at the following Product Page on Internet.
Safety requirements
To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the CAUTIONS contained here.
- The installation of this amplifier must be done by a qualified professional.
- Wear safety glasses, insulated gloves and correct tools for installing this product.
- This amplifier is for use with 12V batteries. Always check the voltage before installing.
- This amplifier must be installed in a firm place with at least 1” space around the heatsink for proper heat spreading.
- Never install the amplifier in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
- Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
- Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
- Before make any connection to amplifier, disconnect the battery negative terminal.
- When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep childrens far from the amplifier.
- This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
- Output connections for speakers may have voltage levels when the amplifier is operating. Make sure that the amplifier is turned OFF before proceed any connection or disconnection in this terminals.
- If you want to dispose this amplifier, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.
Safety
Pay attention to the safety symbols
CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of
important instructions. Failure to heed the instructions will result in risk
of injury to user or product damage
Taramps reserves the right to modify the contents of this document at any time
without prior notice and does not have the obligation to apply the changes in
units which were previously produced
Functions & inputs
-
INPUT: Inputs of signals to be amplified. Connect these signals to RCA outputs of Head Unit, using good quality shielded cables to avoid noise interference.
-
GAIN: It sets the amplifier input sensitivity, which allows an optimal adjustment to the output signals levels of nearly all models of Head Units found in the market. The MIN position of this control allows to receive up to 4V RMS signals into RCA inputs.
-
CROSSOVER: Set the operating mode of amplifier :
-
SELECTOR POSITION – FULL
Amplifies the whole audio range, responding from 10Hz to 20KHz. This function is normally used when there is an external crossover in the system. -
SELECTOR POSITION – HPF – (HIGH PASS)
Amplifies signals with more intensity above 90Hz. This type of function is used mid-bass, mid-range speakers or tweeters. -
SELECTOR POSITION – LPF – (LOW PASS)
Amplifies only bass signal, the response is limited to 90Hz (-12dB/8ª), an optimal frequency cutoff for sub-woofers. -
HIGH LEVEL INPUT: Input for high level / low impedance signals (from the speaker output of the head unit), it features function auto turn on by the input signal, compatible with head units with speaker diagnosis (A.S.S. Advanced Speaker Simulation OEM HU) so it eliminates the need of the REMOTE IN wire from the power connector when using this input.
Note : The system is designed for use in virtually all head units on the market. However, on some you may not get the auto turn on function due to the type of audio output circuit. In this case, use the REMOTE wire. -
ON: Indicates that amplifier is on.
Output & power supply connector
OUTPUT : To connect the speakers. Follow the polarity and the minimum impedance recommended. For STEREO connections, the minimum impedance is 2 ohms at each channel; for BRIGDE connections is 4 ohms. To combine speakers, the resulting impedance must be taken in consideration.
See the examples below:
POWER (Power Supply Connector): The connector terminal (+) must be connected to the battery’s positive pole with a 10mm² / 7 AWG (minimum) wire gauge. The connector terminal (-) must be properly connected to the battery’s negative pole with a same wire gauge. The remote terminal must be connected to the Head Unit REMOTE output with a 0.75mm² / 18 AWG wire. (Except when using the HIGH INPUT).
CAUTION Before making any connections to the power terminals, make sure that the negative (-) of the vehicle battery is disconnected
Protection system
Short-circuit Protection: Shutdown the amplifier when detect a short- circuit or impedance lower than the supported at output. The amplifier will back to normal operation as soon as the short-circuit or overload condition is removed
Installation
CAUTION : All connections to power supply, input and output connectors must be carried out only with the amplifier off.
*Recommended wire gauge & fuse**
- Positive / negative power supply cable __ 7
- AWG Output cables wire gauge___ 15
- AWG Remote cable _____ 18
- AWG Protection fuse or circuit breaker_____ 80A
Calculated considering a maximum length of 4m. Distance greater than this, you
will need to increase the cable gauges.
Using wire gauges below the recommendation will result in power loss and
overheating of wiring.
Check polarity and never reverse power supply cables due to the risk of damage
to the amplifier. It is compulsory to install protection fuses or circuit
breakers as close as possible from batteries.
Technical features
Rated power with 60Hz sinusoidal signal and THD <= 10%, with resistive loads
(2 ohms) in each channel, measured with Audio Precision APx525 audio analyzer
or equivalent, product at lower than 50°C case temperature and 14.4v supply
voltage.
Frequency response measured at 2 times the minimum impedance, in 4-channel
mode The values as above are typical and may vary, due to electronic
components tolerance or manufacturing process. For further information or
questions, visit our website or contact TARAMPS support.
Manufactured by :
TARAMPS ELECTRONICS LTDA CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121 • Res. Manoel Martins Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil MN_016804_R00
www.taramps.com.br
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>