MYBAT PRO M97 Bluetooth Earphones User Manual

June 1, 2024
MYBAT PRO

MYBAT PRO M97 Bluetooth Earphones User Manual
MYBAT PRO M97 Bluetooth Earphones

Product Overview

Product Overview

  1. Volume Down
  2. LED Indicator
  3. Micro USB
  4. Charging Base Connector
  5. Multi-Function Button
  6. Volume Up
  7. Microphone

Package Includes:

A. MyBat Pro Eztalk Wireless Headset x 1
Package Includes
B. Charge Base x 1
Package Includes
C. Micro USB Charging Cable x 1
Package Includes
D. User Manual x 1
Package Includes

Basic Operation:

Button Function Operation Instruction
MFB Power On Press & Hold Button for 1 to 3 seconds
Power Off Press & Hold for 5 seconds
Pairing Mode When powered off, press & hold for 5 to 8 seconds. If on and

unconnected, double press the button to enter pairing mode.
Play / Pause| Quickly press button
Redial a call| Double press the button to dial previous call
Vvoice Command| Press & Hold for 1 second then release to activate
Audio Switch| Press & Hold for 1 second to switch between phone and audio functions
Answer call| Quickly press button when call is incoming
End Call| Quickly press button during the call
Reject call| Press & Hold for 1 second when call is incoming
Volume
+| Volume Up| Quickly press button
Next Song| Press & Hold for 1 second
Volume-| Volume Down| Quickly press button
Previous Song| Press & Hold for 1 second

Bluetooth Pairing and Setup:

A. When powered off, press & hold for 5 to 8 seconds. If on and unconnected, double press the button to enter pairing mode. LED Indicator light on headset will flash blue and red when in pairing mode.
B. Turn bluetooth settings on your device and search for “MyBat Pro Eztalk on list to connect. LED Indicator will flash blue once connected. ted.
C. Control volume, answer calls, and skip tracks all from the MyBat Pro Eztalk Wireless Headset

Connect Two Devices:

A. Follow instructions to pair the first device as noted above. Once connected, turn of the bluetooth function for the first device.
B. Double press the button on Headset to enter pairing mode, check LED Indicator is flashing blue & red alternatively.
C. On the second device, turn the bluetooth settings on and search for “MyBat Pro Eztalk on list to connect. LED Indicator will flash blue once connected.
D. Turn the Bluetooth settings back on the first device to reconnect to MyBat Pro Eztalk” and now both devices will be connected.
Connect Two Devices

Music can only be played from one device, no matter if there are two devices connected. If you would like to play music from the secondary device, the music app and function must be stopped from the first device. The same applies for calls.

LED Indicator

Mode LED Indicator
Power on LED Blue flashes 1 second
Power off LED Red flashes 1 second
Pairing mode LED Red & Blueflashes alternately
Connected LED Blue flashes once every 5 seconds
Charging Solid LED Red
Full charged Solid LED Blue
Low battery LED Red flashing

Charging

Please charge the EZTALK Wireless Headset as soon as the LED flashes Red. Charging time is approx. 2 hours. The LED will turn Blue once fully charged.

  1. Charge Connections

Charge with Micro USB Cable (“Adapter Sold Separately)

  1. Charging Base
    Charging Base
    Charging with Charge Base

Please place the EZTALK Wireless Headset onto the charging base, then connect the base to the Micro USB cable. “Adapter Sold Separately.

Note: Please charge this headset at least once every two months if not in use. Please charge this headset at least once every two months if not in use.

Product Specification:

Bluetooth Version: Bluetooth V5.0.
Bluetooth Chipset: CSR 8615
Operation Range: 10M
Bluetooth Protocols: HSP HFP A2DP AVRCP
CODEC Code: SBC
Battery Capacity: 180maH/3.7V
Charging Time:
Stand-by Time: 200H
Working Time: About 17H (50% Volume)
Headset Net Weight: About 51g Charge Base Net Weight: About 242g
Headset Dimension: 163.21 142.27 48.5mm
Charge Base Dimension: 797331mm

Actual working time wilf vary depending on type of usage.

Notice of compliance

The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

FCC rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

  • Increase the separation between equipment and receiver
    Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected.

  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FAQs

My device is no longer connecting to the EZTALK Wireless Headset. How do I

reconnect?

‘The Wireless Headset will automatically try to connect with a device it was successful paired with If unsuccessful, please disconnect the bluetooth paiting from your device and initiate the pairing process from the beginning.

How can | remove a paired device from the EZTALK Wireless Headset?

To remove paired devices, press and hold both Volume Up and Volume Down buttons at the same time for 5 seconds. The LED Indicator will flash Blue and Red which means the pairing has been removed successfully. If there is a pairing connection problem, you can try this step to reset pairing

What is the password for pairing?

If your device requires a password for pairing, try one of the following options below: 0000, 8888, 1111 or 1234. Note, not ail devices require a password to be entered

What power source do | need to use to charge the Wireless Hoadset?

Any standard USB-A compatible adapter or port will allow you to charge the Headset. Please note the adapter or power source is not included, only the Micro USB Cable and Charging Base.

How can enter Three-Way Calling mode?

If a secondary call is incoming, quickly press the Multi-Function Button to answer the new call and hang up the current call. To put your current call on hold, double press the button to answer the new call. To reject an incoming call while on the phone, press and hold the button for 1 second. To switch between calls, quickly double press the bution to alternate between callers.

WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov
Made in China

SCAN OR CODE TO ACCESS LIFETIME
WARRANTY
QR Code

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals