MYBAT PRO TT-RSKUSU024 Wireless Bluetooth Speaker User Manual
- June 15, 2024
- MYBAT PRO
Table of Contents
VIBEBUDDY
BLUETOOTH SPEAKER
Wireless Bluetooth Speaker
( User Manual )
Model: TT-RSKUSU024
Safety Measures
To ensure proper use of this product, please take the time to read this instruction manual carefully before use. Please observe all the instructions about safe operation and please keep this instruction manual in a safe place for future reference.
- Protection of power supply wire: Do not place the cable in the path of foot traffic. Do not place heavy furniture on the cable. Never pull the cable to unplug the unit from the socket, always disconnect the unit from the main power supply by pulling the plug out of the socket.
- Ventilation: In order to prevent this unit from overheating, place it in a well-ventilated area on astable surface. Never place it on a bed, sofa o carpet where the ventilation will be restricted.
- Dismantling: In order to avoid the risk of electric shock, do not dismantle the unit. Should your unit be faulty or broken please refer servicing to an authorized service center.
- Strange Odor: Should the speaker emit any strange odor, immediately unplug it from the wall socket. Do not use the unit again until you have had it repaired or contacted the manufacturer.
- Do not expose this unit to liquid of any kind
What’s in The Box
- MyBat Pro Vibebuddy Bluetooth Speaker x 1
- Micro USB Charging Cable x 1
- 3.5mm Audio Cable x 1
- Straps x 1
- User Manual x 1
Product Overview
- Strap Attachments.
- Speaker
- LED Lights
- Charging Port
- Indicator Light
- U Disk Slot / Power Bank Output Port
- Aux Input Port
- TF Card Slot
- Composite Bass Diaphragm
Control Panel
- Mode: Bluetooth / MP3/FM
- Press and hold to decrease the volume or click for previous track
- Press and hold to turn the power on or off.
- Press and hold to increase volume or click to skip track.
- Play / Pause; FM mode: Press and hold to search FM channels.
Specifications
Model | 17-RSKUSUO24 |
---|---|
Loudspeaker Output | 5W x 2 |
Horn Size | 52mm |
Bluetooth Version | 5.0 |
Bluetooth Range | 10m / 33ft |
Frequency Response Range | 90Hz — 20KHz |
Signal Noise Rate | 80DB |
Battery Capacity/Voltage | 2000mAh / 3.7V |
Battery Charge Time | 2H |
Working Time | 4H |
USB Power Input | 5V/1A |
Product Size | 215 x 95 x 105mm |
Charge the Speaker
Please charge the speaker for at least 3 hours before using it for the first time. Insert the charging cable into the Micro USB charging port connect the USB plug into 5V/1A USB power Charger.
Power On / Power Off
- Power On: Press and hold [ ] for 3 seconds until you hear the voice prompt say “Power On”.
- Power Off: Press and hold [ ] for 2 seconds until you head the voice prompt say “Power Off”.
Bluetooth Mode
- Once the speaker is turned on, a voice prompt willsay ” Ready to Pair”.
- Turn the Bluetooth settings on your device
- Search for ” MyBat Pro Vibebuddy ” and select it to pair. Once the device and speaker pair, a voice prompt will confirm ” Paired Successfully “.
- Press[ ] button to play music.
- Hangs-free : Press the [ ] boutton to answer the call; during a call, press [ ] button to hang.
Power Bank Function
Charge your mobile device with the power bank feature. Plug in the charging cable to the USB port and connect to your device to start charging.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate
radiofrequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC waning statemens
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harrmful iterference ina
residental installation. This equipment generates, usesr and can radite radio
frequency energy and, if ot installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur ina particular
installation. If his equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
an, the user is encouraged totry to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving artenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Caution: Any changes or modfications to this device not explicity
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two condiiions:
- This device may not cause harmful nterference, and
- this device must acceptany interference received, including interference that may cause udesired operation.
The device has been evaluated to meet general RF expostre requirement
SCAN QR CODE TO ACCESS LIFETIME WARRANTYhttps://linktr.ee/MyBatPro?utm_source=qr_code
WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov
Made in China
DESIGNED IN CALIFORNIA
Documents / Resources
|
MYBAT PRO TT-RSKUSU024 Wireless Bluetooth
Speaker
[pdf] User Manual
TT-RSKUSU024 Wireless Bluetooth Speaker, TT-RSKUSU024, Wireless Bluetooth
Speaker, Bluetooth Speaker, Speaker
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>