PHOENIX VS7630-00 Vivid Slimline Wall Basin Outlet Instruction Manual
- June 1, 2024
- Phoenix
Table of Contents
PHOENIX VS7630-00 Vivid Slimline Wall Basin Outlet
Product Information
Specifications:
- Model: IN0200 REV B
- Recommended Working Pressure: Not specified
- Maximum Hot Water Temperature: Not specified
Product Usage Instructions
Installation:
- Release the grub screw and remove the spout from the spout base.
- Apply Teflon tape to the elbow thread.
- Ensure that the O Ring is fitted to the spout base.
- Screw the spout base onto the elbow thread using a spanner.
- Push the spout onto the spout base and fasten the grub screw securely.
- Test and check for leaks.
Maintenance and Care:
- Chrome plated surfaces should be cleaned with mild liquid detergent or soap and water.
- Avoid using cream cleaners or citrus-based cleaning products as they are abrasive.
- Using unsuitable cleaning agents may damage the surface, andany resulting damage will not be covered by warranty.
Disclaimer:
While we aim to ensure the specifications shown are correct at the time of printing, Phoenix Tapware reserves the right to make modifications without prior notice. Always use the physical product measurements for mark-ups and roughing-in as the line drawing shown may differ from the actual product over time.
*All measurements are shown in millimetres.
Contact information: (03) 9780 4200, Website: www.phoenixtapware.com.au
FAQ
- Q: What should I do if the pressure exceeds 550kpa?
- A: If the pressure exceeds or is likely to exceed 550kpa, an approved pressure-limiting device must be installed to prevent any issues. Failure to comply with this requirement may void all warranties.
- Q: How should I clean chrome-plated surfaces?
- A: Chrome-plated surfaces should be cleaned with mild liquid detergent or soap and water. Avoid using cream cleaners or citrus-based cleaning products as they are abrasive and may damage the surface, which would not be covered by warranty.
- Q: Where can I find the full warranty statement for the product?
- A: Please refer to the full warranty statement enclosed with the product before installing. Alternatively, you can visit www.phoenixtapware.com.au to download a copy of the warranty statement.
Installation Instruction
- Release the grub screw and remove the spout from the spout base
- Apply teflon tape to the elbow thread. Ensure that “O” Ring is fitted to the spout base. Screw the spout base onto the elbow thread with a spanner.
- Push the spout onto the spout base. Fasten Grub Screw. TEST & CHECK FOR LEAKS
NOTE:
- If the pressure exceeds or is likely to exceed 550kpa, an approved pressure-limiting device must be installed.
- Flush out all pipe work prior to installation.
- If the water temperature exceeds 75°C, an approved tempering valve must be fitted.
- Installation should comply with Australian standard AS3500.1 or relevant local authority requirements. Showers may not be suitable for use within:
- Gravity-fed water systems
- Some instantaneous hot water systems; or
- Pressure supply less than 150kPa;
NOTE: The 500kPa maximum water supply pressure does not apply to fire service outlets.
Failure to comply with the above may void all warranties.
WARRANTY:
Please refer to the full warranty statement enclosed with the product before installing. Or visit www.phoenixtapware.com.au to download a copy.
MAINTENANCE AND CARE
- Chrome-plated surfaces should be cleaned with mild liquid detergent or soap and water.
- Do not use cream cleaners or citrus-based cleaning products, as they are abrasive.
- Use of unsuitable cleaning agents may damage the surface. Any damage caused in this way will not be covered by warranty.
DISCLAIMER:
While we aim to ensure the specifications shown are correct at the time of
printing, Phoenix Tapware reserves the right to make modifications without
prior notice. Always use the physical product measurements for mark-ups and
roughing-in as the line drawing shown may differ from the actual product over
time.
*All measurements are shown in millimetres.
- (03) 9780 4200
- www.phoenixtapware.com.au