be quiet SYSTEM POWER 9 Power Supply User Manual

be quiet SYSTEM POWER 9 Power Supply

WARNINGS AND SAFETY INSTRUCTIONS

• Never open the power supply case. The electronic components inside the case generate a high voltage that is dangerous to humans.
• A power supply must only be opened by an authorised technician!
• Caution! Only use the supplied cable set. Using cables that were not included (e.g. cables of older power supply unit series) may lead to defects!
• The warranty shall be void if the power supply is opened by an unauthorised technician and/or the warranty seal is broken. Never handle the power supply with wet or damp hands when in operation. Never insert objects into the openings/fans of the power supply. Operation is only permitted indoors! Outdoor use may lead to severe damage.
• Do not carry out work on the power supply if it is connected to the mains. Always turn the mains switch to off and pull out the mains plug.
• In the event of a short circuit in the device, remove the mains cable and do not use the device.
• If there are traces of smoke, damaged cables and exposure to liquids, the power supply must immediately be disconnected from the mains and must not be used.
• Do not operate the PC directly next to a heater or another source of heat, as this reduces the lifespan of all components and may lead to failures.
• Ensure that there is sufficient ventilation in the PC case, for example by adding additional fans.
• Should you want to clean your power supply, disconnect it completely from the mains and do not use damp cloths or cleaning detergent. Clean the power supply from the outside using a dry cloth.
• Allow one hour before using the power supply after it has been in an ambient air environment as otherwise condensation water could accumulate in the power supply.

COMPATIBILITY

be quiet! System Power 9 power supplies are compatible with current power supply and mother-board specification, such as: Intel ATX12V Power Supply Design Guide Version 2.4 (and downward compatible to V2.31 /V2.3 / V 2.01 / V 2.0), ATX System Design Guide Version 2.2 and Version 2.1, BTX Version 1.0a, EPS 12V V2.92 (550-700W), Intel C6/C7, Energy Star 6.1, ErP ready.

INSTALLING YOUR NEW POWER SUPPLY

You must read the item “Warnings/safety instructions” before beginning installation. You will need a screwdriver to fit the power supply in your PC. Only use the screws supplied with the power supply, as these have the suitable thread.

First remove your old power supply. To do this, proceed as follows:

1. Carefully disconnect your PC from any power sources and pull out all cables connected to the PC.

2. Open the PC case also following the manufacturer’s instructions.

3.  Disconnect all plugs from the motherboard and all other components, such as a HDD or optical drive. Ensure that there are no plugs from the old power supply connected to any of the components.

4. Now remove the screws on the rear of the power supply and take it out carefully. Make especially sure that no cables get caught in the components and damage them.
   Installing your be quiet! System Power 9 power supply:

5. Place the power supply in the space provided in the case and mount it to the rear with the four screws provided. Do not use excessive force.

6.  Plug the 20/24 pin connector into the socket provided on the motherboard. If you have a 24 pin connector, put the remaining 4 pins in the right position before plugging the connector into the socket. If using a 20 pin connector, simply leave the additional 4 pins on the side.

7. Now connect the 4 pin connector, also called the P4 connector, into the socket provided on the mother-board. This connector is going to supply your PC with additional power.

DIMENSIONS & INCLUDED ACCESSORIES

Dimensions of Power Supply: 140mm x 150mm x 86mm
This item is delivered with: mains lead, operating manual, screws for installing the power supply.

MANUFACTURER’S DATA & WARRANTY

Our warranty conditions apply, which can be viewed on the internet on www.bequiet.com.
Your original purchase receipt and serial number will be required before warranty performance is rendered. Please keep it in a safe place.

Listan GmbH . Wilhelm-Bergner Straße 11c . 21509 Glinde . Germany
For further information, you can contact us via e-mail: service@bequiet.com

LEGAL NOTICE, COPYRIGHT

Copyright © Listan GmbH 2020. All rights reserved.
Please note the following:

• The content of this documentation may not be copied, transmitted, distributed or stored in any form, whether in whole or in part, without the prior written approval of Listan.
• be quiet! is a registered trademark of Listan GmbH. Other product and company names mentioned in this documentation may be trademarks or trade names of their respective owners.
•  In accordance with its policy, Listan continually develops its products further. Listan therefore reserves the right to make changes and improvements to any of the products described in this documentation without prior notice.
• Listan is under no circumstances responsible for the loss of data and income or for any specific, incidental, indirect or direct damage, however this may be incurred.

The content of this documentation is presented in its most updated form. Listan neither expressly nor implicitly assumes any liability for the accuracy or completeness of the content of this documentation, including, but not limited to the implicit guarantee of market suitability and the appropriateness for a certain purpose, unless applicable laws or case law prescribe such liability.
Listan reserves the right to make changes to this documentation or to withdraw the documentation at any time without prior notice.

TECHNICAL DATA

MINIMAL LOAD

POWERLABE

OPERATING CONDITIONS

DISTRIBUTION AND PIN ASSIGNMENT

24 pin ATX power connector

1

| ****

+3.3VDC

| ****

13

| +3.3VDC

+3.3Vdef. sense

2| +3.3VDC| 14| -12VDC
3| COM| 15| COM
4| +5VDC| 16| PS_ON/OFF
5| COM| 17| COM
6| +5VDC| 18| COM
7| COM| 19| COM
8| PWR_OK| 20|
9| +5VSB| 21| +5VDC
10| +12VDC| 22| +5VDC
11| +12VDC| 23| +5VDC
12| +3.3VDC| 24| COM

PCI express VGA connector

+12V power connector

SATA power connector

Peripheral Devices

CONNECTIVITY AND CABLE LENGTH

References

• be quiet! - Silent PSUs, cases and PC cooling products. PSU calculator and cooler check for your PC
• be quiet! - Silent PSUs, cases and PC cooling products. PSU calculator and cooler check for your PC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>