PHOENIX IN0246 REV C Vivid Slimline Wall Basin Mixer Set Instruction Manual
- June 1, 2024
- Phoenix
Table of Contents
PHOENIX IN0246 REV CVivid Slimline Wall Basin Mixer Set
Specifications
- Model: IN0246 REV C
- Centre Distance of Breach: 120mm or 140mm
- Adjustment Range: 45mm to 65mm
- Working Pressure: Recommended maximum hot water temperature
Installation Steps
- Screw the Mixer Breach onto the Noggin ensuring level alignment.
- Connect hot and cold water supply following the provided instructions.
- Check the centre distance of the breach assembly (120mm or 140mm) and mark the centre line accordingly.
- Create a 25mm hole and a 45mm hole on the cement sheet and tiles as directed.
- Adjust the range from the finished face of the tiles to the noggin to be between 45mm and 65mm.
- Apply Teflon tape to the Elbow Thread before pushing the dress plate into position.
- Screw the Spout Adaptor to the Elbow Thread using a spanner or= Allen Key.
- Secure the Wall Outlet by pushing it onto the spout adaptor and fastening Grub Screws.
- Fit the Mixer Handle into position and tighten the Grub Screw to secure it. Place the Screw Cap into position.
Maintenance and Care
- Clean the product with mild liquid detergent or soap and water.
- Avoid using cream cleaners or citrus-based products as they are abrasive.
- Using unsuitable cleaning agents may damage the surface, not covered under warranty.
FAQ
Q: What should I do if the pressure exceeds 550kpa?
A: An approved pressure-limiting device must be installed to prevent damage
and maintain warranty coverage.
INSTALLATION INSTRUCTIONS
WALL MIXER SET
IN0246 REV C
-
Screw the Mixer Breach onto Noggin.
Ensure that the Outlet and Mixer Body centres are level. -
Connect hot and cold water supply, as shown.
Test and check for leaks. -
Check centre distance of the breach assembly for 120mm or 140mm size.
- Mark centre line according to measured result.
- Create a 25mm hole and a 45mm hole on the cement sheet and tiles, as shown.
- Centre Distance : 120mm or 140mm
-
Remove the protective cover from the mixer. Apply Teflon tape to Elbow Thread.
Gently push the dress plate into position.
Screw Spout Adaptor to Elbow Thread with a spanner or Allen Key. -
Push Wall Outlet to the spout adaptor and fasten Grub Screws to secure Wall Outlet.
Fit Mixer Handle into position and tighten Grub Screw to secure handle.
Fit Screw Cap into position.
NOTE:=
- If the pressure exceeds or is likely to exceed 550kpa, an approved pressure limiting device must be installed.
- Flush out all pipe work prior to installation.
- If the water temperature exceeds 75°C, an approved tempering valve must be fitted.
- Installation should comply with Australian standard AS3500.1 or relevant local authority requirements.
Showers may not be suitable for use with in
- Gravity-fed water systems
- Some instantaneous hot water systems; or
- Pressure supply less than 150kPa;
NOTE: The 500kPa maximum water supply pressure does not apply to fire service outlets.
Failure to comply with the above may void all warranties.
WARRANTY
Please refer to the full warranty statement enclosed with the product before installing. Or visit www.phoenixtapware.com.au to download a copy.
MAINTENANCE AND CARE
- Products should be cleaned with mild liquid detergent or soap and water.
- Do not use cream cleaners or citrus based cleaning products, as they are abrasive.
- Use of unsuitable cleaning agents may damage the surface. Any damage caused in this way will not be covered by warranty.
DISCLAIMER
While we aim to ensure the specifications shown are correct at the time of
printing, Phoenix Tapware reserves the right to make modifications without
prior notice. Always use the physical product measurements for mark-ups and
roughing-in as the line drawing shown may differ from the actual product over
time.
*All measurements are shown in millimeters.
(03) 9780 4200
www.phoenixtapware.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>