LITHONIA LIGHTING OLWP LED SWW2 120 PE Dusk to Dawn LED Wallpack With Color Switching User Manual

LITHONIA LIGHTING OLWP LED SWW2 120 PE Dusk to Dawn LED Wallpack With

Color Switching

Specifications

• Product Name: Dusk to Dawn LED Wallpack with color switching
• Model Number: OLWP LED SWW2 120 PE
• Mounting Hardware Included: Yes
• Silicone Sealant Required: Purchase Separately

Installation

1. Ensure the delivery matches the catalog description on the packing slip.
2. Disconnect or turn off power before installation.
3. Use a Philips Head Screwdriver and Caulking for installation.
4. Mount the fixture securely using the included mounting hardware.
5. Apply silicone sealant as required to ensure weatherproofing.

Safety Instructions

• Always wear gloves and safety glasses when handling the luminaire.
• Avoid direct eye exposure to the light source.
• Allow the lamp/fixture to cool before handling to prevent burns.
• Do not exceed the maximum wattage marked on the luminaire label.
• Keep combustible materials away from the lamp/lens to prevent fire hazards.

Maintenance

1. Regularly inspect and clean the fixture to ensure optimal performance.
2. Follow manufacturer’s recommendations for driver type, mounting locations, and lamp replacements.
3. Use only lamps that comply with ANSI standards.

FAQ
Q: What should I do if the fixture is damaged upon delivery?
A: If the fixture is damaged, report it to the delivery carrier and compare the catalog description with the fixture label to ensure you have received the correct merchandise.

INSTALLATION INSTRUCTIONS

Dusk to Dawn LED Wallpack with color switching

OLWP LED SWW2 120 PE

• Protect yourself. Before installing, read the entire instructions carefully and save them for future reference.
  Date installed:_

• Failure to follow any of these instructions could void product warranties. For a complete list of product Terms and Conditions, visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.

• Upon receipt of fixture, thoroughly inspect for any freight damage. All damage should be reported to the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the housing to be sure you have received the correct merchandise.

Mounting Hardware IncludedMounting Hardware Included Silicone Sealant Required Purchase Separately REQUIRED TOOLS:

Philips Head Screwdriver Caulking

READ AND FOLLOW THESE SAFETY INSTRUCTIONS!

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture

• box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.

• For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electical code.

• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.

• This fixture is intended to be connected to a properly installed and grounded UL listed junction box.

• It will occasionally be necessary to clean the outside of the refractor/lens. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
  Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov

• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING
RISK OF ELECTRIC SHOCK

• Disconnect or turn off power before installation or servicing.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.

CAUTION
RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.

WARNING
RISK OF BURN

•  Allow lamp/fixture to cool before handling. Do not touch enclosure, lens or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer’s warnings, recommendations and restrictions including but not limited to: driver type, burning position, mounting locations/methods, replacement and recycling.
• Use only lamps that comply with ANSI standards.

CAUTION RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances affected by heat.

CAUTION
RISK OF PRODUCT DAMAGE

• Never connect components under load.

• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.

• Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy sensor, timing device, or other related control devices. LED fixtures must be powered directly off a switched circuit.

• Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around the fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or cooling.

• Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature.

• Only use fixture in its intended location.

• LED products are Polarity Sensitive. Ensure proper Polarity before installation.

• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of unit.

• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
  Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance. Changes or modifications not expressly approved by Acuity Brands Lighting could void the authority to operate the equipment.

• Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when used in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

5- YEAR LIMITED WARRANTY

Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.

FIXTURE PACKING LIST

Description Quantity

• A Light Fixture……………………………………………………………….. 1
• B Buttons to choose color and dusk to dawn on/off…………….. 2
• C Mounting bracket (pre-installed)……………………………………. 1
• D 3” Center Mounting screw (pre-installed) ……………………….. 1
• E 3/4” #6, #8 & #10 Mounting Screws*……………………………… 6
• F Wire Nuts*………………………………………………………………….. 3
• G Rubber Plug*……………………………………………………………… 1

*Contained in parts packs

Remove fixture components and parts pack. Check to ensure all parts are included. Note: Account for small parts and destroy packing material, as these may be hazardous to children.

SELECT MOUNTING LOCATION

This fixture is intended for installation to properly installed and grounded UL listed round recessed or surface mounted weatherproof junction box. Suitable for wall mount above 4ft (1,2m) from ground.
Do NOT install Nearby large, light-colored objects, reflecting light may trigger the shut-off feature. Do not point other lights at the daylight sensor.
Turn OFF Power at fuse or circuit breaker box! CAUTION: Do not rely on wall switch alone to turn off power.

Connect fixture to a 120 Volt, 60Hz power source.

INSTALL MOUNTING BRACKET TO JUNCTION BOX

• Loosen the center mounting screw (D) and remove the mounting bracket. Note: Center mounting screw and bracket are pre-installed on the light fixture for shipping.
• • Install the mounting bracket (C) to the junction box using two 3/4” mounting screws (E). Note: Choose one of the 3 screw sizes provided depending on your junction box.

CAUTION: WIRING
Make sure power is turned off.

• Use wire nut to connect the bare copper or green house supply ground wire to the green fixture ground wire. Note: If house wiring does not include a ground wire, consult your local electrical code for approved grounding methods.

For proper connection, place wire nut over wires and twist clockwise until tight.

• Use wire nut to connect the white fixture wire to the white (neutral) house supply wire.
• Use wire nut to connect the back fixture wire to the black house supply wire.

 FIXTURE INSTALLATION See Fig. A.

• Tuck wires into junction box
• Align fixture over j-box and secure to mounting bracket by tightening center mounting screw (D). Note: Make sure no wires are pinched before tightening.
• Insert rubber plug (G) into center hole to cover the center mounting screw head for moisture seal.

Turn on electricity at fuse or circuit breaker box and verify success of installation.

Note: The Dusk to Dawn function is factory set in OFF position to allow the fixture light to turn on during daytime for testing. After testing push button to set in ON postion for Dusk to Dawn operation. Note: there is a 4 second delay!
This Fixture allows you to choose your light color. Push button to cycle through warm/3000K, cool/4000K and daylight/5000K. See Fig. B

MOISTURE SEAL

Apply silicone caulking (not included) around the perimeter of the fixture back where it contacts the mounting surface for moisture If this fixture fails to operate properly, use the guide below to diagnose and correct the problem.

Troubleshooting Guide

1. Verify that power is turned on at switch and breaker
2. Verify that line voltage is correct
3. Check wiring and connections.
4. Test if Photocontrol works properly

The photocontrol in this fixture is designed to turn on fixture light at low light levels.

If light does not come on or stays on

Test if Photocontrol works properly

• Cover Daylight sensor – Light should come on.
• Shine a flashlight into Daylight sensor -Light should go off.

If fixture cylcles on and off
Light reflecting back off any surrounding surfaces enters the daylight sensor. To correct problem, reposition the fixture or eliminate reflective surface.

If further technical assistance is required, contact:
Technical Support at: 800-705-7378

Cleaning and Maintenance

This LED light provides low maintenance service with no bulbs to change. Clean surfaces with mild soap and water. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

WARNING: There are no user serviceable parts inside fixture.

Acuity Brands Lighting, Inc.
One Lithonia Way, Conyers, GA 30012 www.AcuityBrands.com

References

• Acuity Brands | Lighting, Controls, and Building Management Solutions
• Acuity Brands | Lighting, Controls, and Building Management Solutions
• U.S. Environmental Protection Agency | US EPA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>