LITHONIA LIGHTING CNY LED Led Canopy Instruction Manual

LITHONIA LIGHTING CNY LED Led Canopy

Product Information

Specifications

• Product Name: LED Canopy CNY LED
• Manufacturer: Acuity Brands Lighting, Inc.
• Warranty: 5-Year Limited Warranty
• Website: www.acuitybrands.com

Product Usage Instructions

Installation Instructions

1. Before installation, read the entire instructions carefully and save them for future reference.
2. Verify the date of installation and thoroughly inspect the fixture for any freight damage upon receipt.
3. Compare the catalog description on the packing slip with the fixture label inside the housing to ensure you have the correct merchandise.

Safety Instructions

WARNING RISK OF ELECTRIC SHOCK:

• Disconnect or turn off power before installation or servicing.
• Verify correct supply voltage by comparing it with the luminaire label information.
• Make all electrical connections following NEC and local code requirements.
• Cap all wiring connections with UL approved wire connectors.

CAUTION RISK OF INJURY:

• Wear gloves and safety glasses when handling the luminaire.
• Avoid direct eye exposure to the light source when it is on.

CAUTION RISK OF FIRE:

• Keep combustible materials away from the lamp/lens.
• Avoid operating close to combustible substances affected by heat.

CAUTION RISK OF PRODUCT DAMAGE:

• Never connect components under load.
• Avoid mounting or supporting fixtures in a way that can damage wire insulation.
• Handle lamps/fixture only when cool and do not exceed maximum wattage marked on luminaire label.

5-Year Limited Warranty
Register your warranty on www.acuitybrands.com/resources/warranty .

FAQs

Q: What should I do if I notice freight damage upon receipt?
A: Report all damage to the delivery carrier immediately.

Q: How can I verify the correct supply voltage?
A: Compare it with the luminaire label information.

Protect yourself. Before installing, read the entire instructions carefully and save them for future reference.
Date installed:_____
Failure to follow any of these instructions could void product warranties. For a complete list of product Terms and Conditions, visit www.acuitybrands.com.
Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.

Upon receipt of fixture, thoroughly inspect for any freight damage. All damage should be reported to the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the inside of the housing to be sure you have received the correct merchandise.

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW THESE SAFETY INSTRUCTIONS!

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
• For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electical code.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
• This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
• It will occasionally be necessary to clean the outside of the refractor/lens. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING
RISK OF ELECTRIC SHOCK

• Disconnect or turn off power before installation or servicing.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.

CAUTION RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.

WARNING RISK OF BURN

• Allow lamp/fixture to cool before handling. Do not touch enclosure, lens or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer’s warnings, recommendations and restrictions including but not limited to: driver type, burning position, mounting locations/methods, replacement and recycling.
• Use only lamps that comply with ANSI standards.

CAUTION RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances affected by heat.

CAUTION
RISK OF PRODUCT DAMAGE

• Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
• Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy sensor, timing device, or other related control devices. LED fixtures must be powered directly off a switched circuit.
• Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around the fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or cooling.
• Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature.
• Only use fixture in its intended location.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
• Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.
• Changes or modifications not expressly approved by Acuity Brands Lighting could void the authority to operate the equipment.
• Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when used in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

5- YEAR LIMITED WARRANTY
Register your warranty on www.acuitybrands.com/resources/warranty. Your prompt product registration confirms your right to the protection available under the terms and conditions of your Lithonia Lighting warranty.
Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.

INSTALLATION INSTRUCTIONS

FIXTURE PACKING LIST

Contained in parts packs
Mounting Hardware and Silicone Sealant Required – Purchase Separately

REQUIRED TOOLS:

Remove fixture components and parts pack. Check to ensure all parts are included. Note: Account for small parts and destroy packing material, as these may be hazardous to children.
Turn OFF Power at fuse or circuit breaker box!

CAUTION: Do not rely on wall switch alone to turn off power.
Not suitable for use with motion sensors or other remote devices.
This fixture is intended for ceiling, wall or stem mount (conduit and stem not included)

For j-box mounting

1. Loosen the screws on the front of housing and slide the housing with lens to the left to detach from top housing. See Figure A
2. Pull power wires all the way through the center hole on the mounting backplate. Fix the back housing to the ceiling using provided mounting screws. See Figure B
3. Make wiring connections using provided wire nuts. See Figure C.
   Re-attach the lens housing to the mounting backplate by sliding the pins back in. Close the housing and screw down, max torque: 1.5ft-lbs (2Nm)

For Pendant Mounting

1. Loosen the screws on the front of housing and slide the housing with lens to the left to detach from top housing. See Figure A
2. Remove rubber wire plug from the top of fixture to expose the NPS threads.
3. Feed input leads through a 3/4” threaded conduit pipe and screw conduit pipe into fixture threading. Note: Seal thread using Teflon tape or silicone sealant.
4. Make wiring connections using provided wire nuts. See Figure C.
   Re-attach the lens housing to the mounting backplate by sliding the pins back in. Close the housing and screw down, max torque: 1.5ft-lbs (2Nm)

For Conduit Mounting see Figure E

1. Loosen the screws on the front of housing and slide the housing with lens to the left to detach from top housing. See Figure A
2. Fix the back housing to the ceiling using provided mounting screws. See Figure B
3. Remove conduit plug. Feed input leads through 3/4” conduit pipe and screw pipe into fixture threading. Note: Seal thread using Teflon tape or silicone sealant.
4. Make wiring connections using provided wire nuts. See Figure C.
   Re-attach the lens housing to the mounting backplate by sliding the pins back in. Close the housing and screw down, max torque: 1.5ft-lbs (2Nm)

CHOOSE SETTINGS (OPTIONAL) – CAUTION: SWITCH CAN ONLY OPERATE WHEN POWER TO FIXTURE IS OFF. WAIT 60 SECONDS BEFORE POWERING AFTER SWITCHING

• To change settings, using a philps head screwdriver, remove the switch cover on the side of the fixture See Figure C. Choose your settings and replace switch cover. Tighten to min. 1.5ft-lbs (2Nm) to max. 1.8ft-lbs (2.5Nm).
• For lumens, factory set to brightest sun (10,000lm). If different brightness is desired select middle sun (7500lm) and for lowest lumens dimmest sun (5000lm).
• For color, factory set to Light Blue (4000K) if different color is desired select Blue (5000K) for the whitest color and Yellow (3000K) for the least white.

CAUTION: WIRING AND FIXTURE OPERATION

Make sure power is turned off.
Connect fixture to supply wires rated for at least 75°C (167°F)
To Ground fixture use Wire Nut to connect the (copper) house supply ground wire & the (green) fixture ground wire. Note: If house wiring does not include a ground wire, consult your local electrical code for approved grounding methods.

For proper connection, place wire nut over wires and twist clockwise until tight.

To connect supply wires use Wire Nuts to connect the black fixture wire to the black power supply wire and the white fixture wire to the white (neutral) supply wire.
Turn on electricity at fuse or circuit breaker and verify success of installation.

Acuity Brands Lighting, Inc.
One Lithonia Way, Conyers, GA 30012
www.AcuityBrands.com

References

• Acuity Brands | Lighting, Controls, and Building Management Solutions
• Post Sales - Consumer Post Sales
• U.S. Environmental Protection Agency | US EPA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>