EMOOR zd-b-006-s Wood Slatted Low Bed Frame Fuji Twin Instruction Manual
- June 2, 2024
- EMOOR
Table of Contents
EMOOR zd-b-006-s Wood Slatted Low Bed Frame Fuji Twin
Thank you very much for your purchase. Read all instructions carefully before assembly. Keep this instruction for future reference.
EMOOR Wood Slatted Low Bed Frame FUJI Twin for Japanese Futon Mattress zd-b-006-s
- Material Natural paulownia wood Plywood
- Dimensions W38.6 x L78.7 x H11.8/7.0/2.4in (98 x 200 x 30/18/6cm)
- Country of Origin China
- Load Capacity 200kg
SAFETY PRECAUTIONS
We do not assume any liability or responsibility for any injury or damage arising from misuse or inappropriate use of the products.
WARNING
Failure to follow these warnings and the assembly instructions could result in
serious injury or death.
- Keep away from the flame.
- Do not smoke in bed. It may cause a fire.
CAUTIONS
- Do not use it on the tiled floor.
- Direct sunlight or direct heating and cooling air from the air conditioner may cause deformation or discolouration.
- Keep away from heat and moisture to prevent rusted screws.
- Ventilate regularly.
- Periodically re-tighten all bolts.
- Be careful not to get injured by the packing materials.
- Domestic use only, not for business, commercial or industrial purposes.
- Do not modify or remodel. It may cause damage or injury.
- Natural disasters or accidents or damage caused by carelessness, improper repair or modification by customers are not guaranteed
- When using on a floor that is easily scratched or dented, protect the floor before assembly.
- In case of unusual shakes or sounds, stop using.
- If the cause is unknown, contact a vendor.
PRECAUTIONS
Please read these before assembly.
- Please wear gloves for safe assembly.
- There is a risk of injury from the small edges of the parts.
- Heavy product. Please be sure to assemble with two or more people.
- Secure the flat and enough space for assembly. To prevent scratches, cover the floor and furniture with a blanket, carpet, or unpacked cardboard.
- Make sure you have all the parts before assembling. Install all the parts accurately
- Tighten all screws loosely first, then tighten them over firmly checking the overall balance finally. Tightening screws from the beginning may cause misalignment of other screw holes or overall distortion
- Assemble in order, or may fail to complete assemble or cause product damage.
KEY POINTS
Secure enough space and assemble in the right order.
Do not tighten up each bolt from the first time.
Tighten each bolt temporarily with about 80%, correct distortion, and then
tighten up all bolts.
Tighten bolts in a diagonal sequence.
Start tightening any bolt (but not tighten up), and 2nd one should be in a
diagonal position. Tighten 3rd and 4th, then back to 1st one and tighten up
evenly.
Parts List
Hardware
Completion drawing
Assembly Points
Secure enough space and assemble in order.
How to bond and connect
Assembly Instructions
STEP 1
First, connect A Side Frames and B Side Frames. Inject 10 Glue into the
mounting holes of 6 Wooden Dowels, insert them as shown in the picture, and
connect the A B Side Frames.
Cautions
Assemble AB Side Frames and D Horizontal Bar with the side with seals on
top.
STEP 2
Align the screw holes on E Support Rails with the screw holes on D Horizontal
Bar, insert 2 Allen Bolt [M] into 12 holes, and temporarily tighten them with
7 Allen Key. Then tighten firmly.
Cautions
Assemble Support Rail E with the felt side facing up.
STEP 3
Attach C Head and Foot Frames. Align the metal parts on the four inner corners
of A B Side Frame with the screw holes of C Head and Foot frame, insert 1
Allen Bolt [S], and temporarily tighten with 7 Allen Key. Then, adjust the
main body straight, and tighten them firmly.
- Height adjustable in 3 levels.
- To adjust the height to your preference, proceed to [STEP 4 for with legs] or [STEP 6 for without legs]
Step 4
- If you want to attach the legs, please assemble them from here.
- If you want to use the bed without legs, please proceed to STEP 6 without attaching the connecting plates.
- Attach 5 Connecting Plates with 3 Wood Screws [S] to the bottom of A B Side Frame, and fix them firmly in 4 places.
- Use a Phillips screwdriver to install Wood Screws.
STEP 5
Attach 8 Floor Protective Felts to the bottom of G Legs. Attach G Legs to the
main body as shown.
In the case of 2 Legs (Uses 12 legs)
In the case of 1 Leg (Uses 6 legs)
SKIP STEP 6 & STEP 7 as they are instructions for using a bed without legs.
STEP 6
- If you want to use the bed without legs, please assemble them from here.
- If 5 Connecting Plates and 3 Wood Screws [S] are attached to the bottom of the A B Side Frame, be sure to remove them.
Cautions
When using it as a floor bed without legs, please do not attach connecting
plates as they may damage the floor.
STEP 7
Attach 9 Floor Protection Felts (Rectangular) to cover 12 bolt holes on the
back of the main body.
STEP 8
- Align the screw holes of F Slatted Board and A B Side Frames, and tighten them from C Head & Foot Frames side with 4 Wood Screws [L]. Next, spread out F Slatted Board firmly and tighten the center part with 4 Wood Screws [L] to complete.
- Use a Phillips screwdriver to install Wood Screws.
Please check after completing the assembly.
- Make sure all the screws, etc. are securely tightened.
- Check that there is no distortion in the entire product and there is no looseness in the connecting bolts.
- Check that all legs are in contact with the floor and there is no wobbling or rattling.
HOW TO CARE
- When cleaning, wipe with a soft cloth tightly dampened with mild detergent and/or water.
- Do not use harsh cleaners or abrasives.
Contact Information
EMOOR.Co., Ltd.
-
1-25-12 Akebonocho Tachikawa Tokyo 190-0012 JAPAN
-
Customer Support
cs@emoor.co.jp.